Bard MULTI-TEC W18ABP Series Literature Assembly page 65

CONTENTS
General Information ....................................................3
List of Necessary Materials/Tools .............................6
Site Preparation ............................................................7
Model Identification ................................................ 7
New Shelter Installation vs. Retrofit Installation ......... 7
Minimum Clearance ................................................ 7
Clearance to Combustibles ....................................... 7
Wall-Mount Unit Mounting .........................................9
Mounting the Units ................................................. 9
Wall-Mount Unit Wiring ............................................15
Main Power Wiring ................................................ 15
Low Voltage Wiring ................................................ 15
Preliminary Start Up ..................................................19
Running in Orphan Mode ....................................... 19
LC6000 Controller Installation .................................20
LC6000 Controller ................................................ 21
Mounting the LC Controller ............................. 21
Installing Remote Indoor
Temperature/Humidity Sensor(s) ...................... 22
Installing Outdoor Temperature/Humidity
Sensor .......................................................... 24
Emergency Off, Emergency Vent and
Generator Run Connections ............................. 25
Communication Wiring .................................... 26
Supply Wiring ................................................ 31
System Set Up .............................................................34
TEC-EYE Hand-Held Diagnostic Tool ....................... 34
TEC-EYE Status Screen .................................. 35
Setting Up Wall-Mount Units for Operation .............. 35
1. Address Each Wall-Mount Unit .................... 35
2. Execute a Run Test on Each Unit ................. 35
3. Clear Unit Alarm Logs on Each Unit ............. 36
Setting Up LC6000 for Operation ........................... 36
4. Set LC Controller Date and Time .................. 36
5. Configure Sensors ...................................... 37
6. Enter Total Number of Units ........................ 40
7. Verify Units are Online ................................ 40
8. Select Economizer Type for Each Zone ......... 40
9. Clear Controller Alarm Logs ......................... 41
10. Complete Installation................................ 41
Additional Information .............................................42
Menu Screens and Password Levels ........................ 42
Setpoints ............................................................. 42
Calibrating Sensors ............................................... 42
Remote Indoor Temperature/Humidity Sensor
Orientation ........................................................... 44
FIGURES AND TABLES
Figure 1 MULTI-TEC W18-36A/LB Model Nomenclature ...6
Figure 2 Dimensions .................................................. 8
Figure 3 Outdoor Sensor Installation .............................9
Figure 4A W18/24 Mounting Instructions ..................... 10
Figure 4B W30/36 Mounting Instructions ..................... 11
Figure 5 Electric Heat Clearance ............................... 12
Figure 6 Wall Mounting Instructions .......................... 12
Figure 7 Wall Mounting Instructions .......................... 13
Figure 8 Common Wall Mounting Installations ............ 14
Figure 9 Circuit Routing Label .................................. 15
Figure 10 WIRING: VAC Supply Wiring Landing Points .. 15
Figure 11 Cooling and Heating Setpoints ..................... 19
Manual 2100-713A
Page 2 of 44
Figure 12 Typical LC6000-200 Component Location .... 20
Figure 13 LC6000 Fused Power Supply Terminal .......... 21
Figure 14 Remote Indoor Temperature/Humidity
Sensor Installation ...................................... 22
Figure 15 Additional Remote Sensor Installation .......... 23
Figure 16 Remote Outdoor Sensor Installation .............. 24
Figure 17 Emergency Off, Emergency Vent
and Generator Run Connections ................... 25
Figure 18 Communication Wiring (Daisy Chain) ............ 26
Figure 19 Communication Wiring (Alt. Method) ............ 26
Figure 20 Placement of Communication Filters ............ 27
Figure 21 Communication Wiring: Termination
at the Controller .......................................... 28
Figure 22 Communication Wiring: Termination
at the First Wall-Mount Unit ......................... 29
Figure 23 Communication Wiring: Termination
at Additional Wall-Mount Units .................... 30
Figure 24 LC6000 Controller Circuit Install .................. 31
Figure 25 Controller Grounding Posts .......................... 31
Figure 26 WIRING: LC6000-200 Wiring Diagram ......... 33
Figure 27 TEC-EYE Connection to Unit Control ............. 34
Figure 28 TEC-EYE Display and Interface..................... 34
Figure 29 Unit Configuration....................................... 35
Figure 30 Executing Run Test ..................................... 36
Figure 31 Clearing Unit Alarm Logs ............................. 36
Figure 32 Setting Controller Date and Time .................. 37
Figure 33 Enable/Disable Zone 1 Indoor Humidity
Sensor ....................................................... 37
Figure 34 LC6000 Controller Display and Interface ......... 37
Figure 35 Enable/Disable Zone 2 Indoor Humidity
Sensor ....................................................... 38
Figure 36 Enable/Disable Zone 3 Indoor Humidity
Sensor ....................................................... 38
Figure 37 Enable/Disable Zone 1 Indoor Temperature
Sensor ....................................................... 38
Figure 38 Enable/Disable Zone1 Remote Temperature
Sensor ....................................................... 39
Figure 39 Enable/Disable Zone 2 Remote Temperature
Sensor ....................................................... 39
Figure 40 Enable/Disable Zone 3 Remote Temperature
Sensor ....................................................... 39
Figure 41 Enable/Disable Outdoor Air Humidity Sensor ...39
Figure 42 Enable/Disable Outdoor Air Temperature
Sensor ....................................................... 40
Figure 43 Total Units Displayed .................................. 40
Figure 44 Selecting Economizer Type .......................... 41
Figure 45 Clearing LC6000 Alarm Logs ....................... 41
Figure 46 Adjusting Sensor Offset Value ...................... 42
Figure 47 Current Sensor Orientation ........................... 44
Figure 48 Earlier Sensor Orientation ............................ 44
Table 1A W**ABP Series (60Hz) Electrical Specs ........ 16
Table 1B W**LBP Series (60Hz) Electrical Specs ........ 17
Table 2 W**ABE Series Electrical Specifications ....... 17
Table 3A W**ABP Series (50Hz) Electrical Specs ........ 18
Table 3B W**LBP Series (50Hz) Electrical Specs ........ 18
Table 4 LC6000-200 Terminal Block Index ............... 32
Table 5 LC6000/TEC-EYE Passwords (Default) .......... 34
Table 6 MULTI-TEC Unit Status Messages ................ 43
Table 7 LC6000 Status Messages ............................ 43