Toro Pro Sneak 360 Operator's Manual page 5

•
Ensure that the area is clear of other people before
operating the machine. Stop the machine if anyone enters
the area.
•
Never leave a running machine unattended. Always stop
the engine, set the parking brake, and remove the key
before leaving.
•
Never jerk the controls; use a steady motion.
•
Watch for traffic when operating near or crossing
roadways.
•
Do not touch parts which may be hot from operation.
Allow them to cool before attempting to maintain, adjust,
or service.
•
Check for overhead clearances (i.e. branches, doorways,
electrical wires) before driving under any objects and do
not contact them.
•
Ensure that you operate the machine in areas where
there are no obstacles in close proximity to the operator.
Failure to maintain adequate distance from trees, walls,
and other barriers may result in injury as the machine
backs up during operation if the operator is not attentive
to the surroundings. Only operate the unit in areas where
there is sufficient clearance for the operator to safely
maneuver the product.
•
Never allow anyone in the trench while operating the
machine.
•
Locate the pinch point areas marked on the machine and
attachments and keep hands and feet away from these
areas.
•
Before operating the machine with an attachment, ensure
that the attachment is properly installed.
•
Lightning can cause severe injury or death. If lightning
is seen or thunder is heard in the area, do not operate
the machine; seek shelter.
Slope Operation
Slopes are a major factor related to loss-of-control and
tip-over accidents, which can result in severe injury or death.
All slopes require extra caution.
•
Avoid operating this machine on slopes.
•
Remove obstacles such as rocks, tree limbs, etc. from the
work area. Watch for holes, ruts, or bumps, as uneven
terrain could overturn the machine. Tall grass can hide
obstacles.
•
Use only Toro-approved attachments. Attachments can
change the stability and the operating characteristics
of the machine. Warranty may be voided if used with
unapproved attachments.
•
Keep all movements on slopes slow and gradual. Do not
make sudden changes in speed or direction.
•
Avoid starting or stopping on a slope. If the machine
loses traction, proceed gradually, straight down the slope.
•
Avoid turning on slopes. If you must turn, turn slowly
and keep the heavy end of the machine uphill.
•
Do not operate near drop-offs, ditches, or embankments.
The machine could suddenly turn over if a wheel goes
over the edge of a cliff or ditch, or if an edge caves in.
•
Do not operate on wet grass. Reduced traction could
cause sliding.
•
Do not park the machine on a hillside or slope without
lowering the attachment to the ground, setting the parking
brake, and chocking the wheels.
•
Only operate the machine on level ground when the
machine is in the narrow wheel configuration.
Rollover Protection Structure (ROPS)
System
•
Before operating a machine with a ROPS (rollover
protection structure), ensure that the seat belt is in good
condition and is securely attached to the machine.
•
Always wear a seat belt when operating a machine with
a ROPS.
•
Inspect the ROPS at the interval recommended in this
manual or when the ROPS has been in an accident.
•
Repair a damaged ROPS using only genuine Toro
replacement parts; do not repair or modify the ROPS.
•
Check carefully for overhead clearances (i.e. branches,
doorways, electrical wires) before driving under any
objects and do not contact them.
•
Do not remove the ROPS except when servicing or
replacing it.
•
Do not add weight to the machine that exceeds the gross
weight displayed on the ROPS label.
Maintenance and Storage
•
Disengage the auxiliary hydraulics, lower the attachment,
set the parking brake, stop the engine, and remove the
key. Wait for all movement to stop before adjusting,
cleaning, or repairing.
•
Clean debris from attachments, drives, mufflers, and
engine to help prevent fires. Clean up oil or fuel spillage.
•
Let the engine cool before storing and do not store near
flame.
•
Do not store fuel near flames or drain indoors.
•
Park the machine on level ground. Never allow untrained
personnel to service the machine.
•
Use jack stands to support components when required.
•
Carefully release pressure from components with stored
energy.
•
Disconnect the battery before making any repairs.
Disconnect the negative terminal first and the positive
last. Reconnect positive first and negative last.
•
Keep hands and feet away from moving parts. If possible,
do not make adjustments with the engine running.
5