Hoshizaki KM-340MAH Manual page 9

Need Service or Repair? Locate your closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-rep
KMD-460 & 530M_H:
Loosen the two thumbscrews on the pump insulation
panel (B) and remove the panel.
Disconnect the discharge hose, the drain valve hose,
and the overflow drain hose.
Disconnect the pump motor and then the float switch
connectors from the control board. co
Remove the two thumbscrews securing the pump Re
m motor and float switch assembly.
Pull out the water tank, cube guide, and pump motor Pu
an and float switch assembly all together.
Re Remove the screw securing the float switch to the
to top of the assembly, remove the float switch*.
Se See Step for cleaning steps. Reassemble in the
re reverse order they were removed.
* Remove retainer rod (take care not to bend excessively) from bottom of the float switch housing & clean all float parts.
R Replace all the Panels, except the Front Panel.
8
M Move the service switch
switch to SERVICE. Replace the Front Panel.
After 30 minutes, remove the Front Panel, move A
9
the service switch to DRAIN. Replace the Front
Panel.
ATTENTION! To prevent damage to the water pump,
do not leave the control switch on SERVICE for
extended periods when water tank is empty.
Cleaning Rinse:
A After 2 minutes, remove the Front Panel, move the
10
the Front Panel.
11
A After 3 minutes, move the
SERVICE. Replace the Front Panel.
12 A After 5 minutes, remove the Front Panel, move the
Replace the Front Panel
13
A After 2 minutes, remove the Front Panel, move the
Repeat 3x (Steps R thru
14
on front...
After
After
3 min.
2 min.
#51009 | 4.28.2017
KMD-410M_H:
Loosen the two thumbscrews securing the
pump motor bracket.
Disconnect the discharge hose.
Disconnect the pump motor and float switch
connectors from the side of the control box.
While pushing up on the snap tab, pull out the
water tank, cube guide, pump motor bracket,
and pump motor and float switch assembly all
together.
Remove the pump motor bracket securing the
float switch to the top of the assembly, remove
the float switch*.
See Step
the reverse order they were removed.
to WASH, and the control
control switch
service switch to WASH, and the
service switch
control switch
) to rinse thoroughly. Continue to Sanitation – Step
After
5 min.
Tech Support: 1.800.233.1940
for cleaning steps. Reassemble in
After
30 min.
to ICE. Replace
control switch to
to DRAIN.
to OFF.
After
Repeat
3 min.
3x
sanitizing continued...
RINSE 1:
(Steps 20-22)
Move control switch to ICE,
replace front panel
After 3 minutes, remove the
front panel
Move service switch to WASH
and control switch to SERVICE,
replace the front panel
After 5 minutes, remove the
front panel
Move service switch to DRAIN,
replace the front panel
After 2 minutes, remove
the front panel
Move control switch to OFF,
replace the front panel
RINSE 2:
Repeat RINSE 1 (Steps 20–22)
for complete ice/food safety
Clean the dispenser unit /
ice storage bin liner with a
neutral cleaner (dish soap)
Rinse thoroughly
Move control switch to ICE,
replace front panel
ATTENTION!
IF ICEMAKER IS ON DISPENSER,
remember to turn on the dispenser
after cleaning
DO NOT use ammonia type cleaners DO NOT use ammonia type cleaners
WEAR liquid-proof gloves and goggles
to protect skin & eyes from cleaning &
sanitizing chemicals
AMMONIA
Cleaners
Scoop
Dish soap, rinse well
Water Filters
Check psi, change if req'd
Exterior
Dish soap & damp cloth
Bin Door/Top Kit
Warm water & clean cloth
Icemaker/Bin
Follow these instructions
Water Supply Inlet
Clean inlet screen
Condenser
Inspect. Clean with brush
Water Hoses
Inspect. Replace if req'd
20
21
e
22
23
24
,
25
Page 2
Page 9