Hoshizaki KM-340MAH Manual page 31

Need Service or Repair? Locate your closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-rep
In In bad water conditions, a more thorough soaking may be
re required. Remove the Left Side Panel and remove the Float
Switch from the Reservoir cover. Clean the Float Switch with
the solution, rinse thoroughly with clean water, and replace it back
in the cover. Follow Step
Hose that will block the flow to the Evaporator Assembly. Pour
additional cleaning solution over the Extruding Head until the
Evaporator Assembly is full.
Allow to soak for 10 minutes, remove the clamp
before operation.
Otherwise, continue to Step
W Wipe down the Infrared Sensor Lens, (located
on the bottom of the icemaker). Rinse the lens
with cleaning solution, then a clean, damp cloth.
If the bottom of the icemaker is not accessible: Remove
the thumbscrew securing the infrared sensor housing, then remove the housing from the base. After
cleaning lens – replace the housing and secure thumbscrew.
R Replace the Top Panel. Move the
IC ICE, then plug in the icemaker. Move the
switch to ON. Replace the Front Panel. Make ice
using the solution until it stops.
R Remove the Front Panel, then move the
switch to OFF. Move the control switch
Move the power switch to ON, replace the Front
Panel. Allow the icemaker to drain completely.
R Remove the Front Panel. Move the
OFF. Open the water supply line shut-off valve to O
supply water to the icemaker.
M Move the control switch to ICE and the
Allow the icemaker to fill the reservoir with water. A
After the gear motor starts, move the A
the control switch to DRAIN, then the
Replace the Front Panel. Allow the icemaker to drain
completely.
The icemaker might make a noise/squealing when first
started due to scale removal from auger/evaporator. This is
normal in bad water conditions and will subside after 20
minutes.
R Remove the Front Panel. Move the
switch s to OFF. Unplug the icemaker. Close
the icemaker water supply line shut-off
valve.
Continue to Sanitation – Step
hoshizakiamerica.com/manuals
Type in the model number of your
icemaker (including dashes) to
download manuals
#51056 | 02.21.2018
, then place a clamp on the Reservoir
.
control switch to
power
power
to DRAIN.
power switch to
power switch to ON.
power switch to OFF,
power switch to ON.
power
on front...
Dish soap, rinse well
Scoop
Water Filters Check psi, change if req'd
Exterior Stainless Steel Cleaner
Dish soap & damp cloth
Underside/Top Kit
Icemaker/Dispenser
Follow these instructions
Clean inlet screen/valves
Water Supply Inlet
Inspect seal bolts/ bearing
Extruding Head
wear. Tighten or replace
Water Hoses
Inspect. Replace if req'd
Tech Support: 1.800.233.1940
Plug In
Drain
Completely
To Icemaker
Or Water Filter
OPEN
Listen for
Gear Motor
to Start
Drain
Completely
To Icemaker
Or Water Filter
SHUT OFF
Unplug
ATTENTION!
DO NOT use
ammonia type
cleaners. Can cause
damage to icemaker
WEAR liquid-proof
gloves and goggles to
protect skin & eyes
from cleaning &
sanitizing chemicals
sanitizing continued...
Rinse the parts thoroughly with
clean water
(if solution is left on
these parts, they will rust)
Replace all parts in their correct
positions
(When installing the baffles,
make sure the bent surface (the one without
faces the actuator so that the
the studs)
bent surface can guide the ice to the
center of the actuator)
Replace all panels except the front
panel in their correct positions
Follow Steps 9-14 using the
sanitizing solution.
SANITIZE 2:
Repeat Steps 15–17 then Step 22
for complete ice/food safety
Remove the front panel
Move the control switch to ICE,
plug in the icemaker
Move the power switch to ON,
replace the front panel
Allow the icemaker to run for
30 minutes
Remove the front panel
Move the power switch to OFF,
unplug the icemaker
Pour warm water into the
dispenser/storage bin to melt any
remaining ice
Clean the dispenser/storage
bin liner and cover with dish
soap and a damp cloth. Rinse
thoroughly with clean water
Plug in icemaker, make sure
control switch is set to ICE.
Move the power switch to ON,
replace the front cover to start the
automatic icemaking process
AMMONIA
Cleaners
ATTENTION!
IF ICEMAKER IS ON DISPENSER,
remember to turn on the dispenser
after cleaning
Page 2
h
Page 31