Hoshizaki KM-340MAH Manual page 29

Need Service or Repair? Locate your closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-rep
In In bad water conditions, a more thorough soaking may be
7
required. Remove the Left Side Panel and remove the Float re
Switch from the Reservoir cover. Clean the Float Switch with
the solution, rinse thoroughly with clean water, and replace it back
in the cover. Follow Step
Hose that will block the flow to the Evaporator Assembly. Pour
additional cleaning solution over the Extruding Head until the
Evaporator Assembly is full.
Allow to soak for 10 minutes, remove the clamp
before operation.
Otherwise, continue to Step
Wipe down the Infrared Sensor Lens, (located W
8
on the bottom of the icemaker). Rinse the lens
with a clean, damp cloth.
M Move the control switch
9
switch to ON. Replace the panels in their correct positions.
Make ice using the cleaning solution until it stops.
Remove the Front Panel. Move the R
10
D DRAIN, then replace the Front Panel. Allow the icemaker
to drain completely.
11 R Remove the Front Panel. Move the
OFF. Open the water supply line shut-off valve to
supply water to the icemaker.
M
Move the control switch to ICE and the
12
A Allow the icemaker to fill the reservoir with water.
A After the gear motor starts, move the
13
switch to DRAIN. Replace the Front Panel.
Allow the icemaker to drain completely.
The icemaker might make a noise/squealing when first started due to scale removal from
auger/evaporator. This is normal in bad water conditions and will subside after 20
minutes.
R Remove the Front Panel. Move the
14
switch to OFF. Replace the Front Panel. Close
the icemaker water supply line shut-off valve.
Continue to Sanitation – Step
hoshizakiamerica.com/manuals
Type in the model number of your
icemaker (including dashes) to
download manuals
#51055 | 2.21.2018
, then place a clamp on the Reservoir
.
to ICE, then move the power
control switch
power switch to
power switch to ON.
control
Listen for
Gear Motor to Start
power
on front...
Dish soap, rinse well
Air Filter/Scoop
Check psi, change if req'd
Water Filters
Exterior Stainless Steel Cleaner
Underside/Top Kit Dish soap & damp cloth
Icemaker/Dispenser
Follow these instructions
Water Supply Inlet Clean inlet screen/valves
Inspect seal bolts/ bearing
Extruding Head
wear. Tighten or replace
Water Hoses
Inspect. Replace if req'd
Tech Support: 1.800.233.1940
to
Drain
Completely
To Icemaker
Or Water Filter
OPEN
Drain
Completely
To Icemaker
Or Water Filter
SHUT OFF
ATTENTION!
DO NOT use
ammonia type
cleaners. Can cause
damage to icemaker
WEAR liquid-proof
gloves and goggles to
protect skin & eyes
from cleaning &
sanitizing chemicals
sanitizing continued...
Remove the front panel
Move control switch to DRAIN,
replace the front panel
Allow the icemaker to drain
completely
Remove the front panel
Move power switch to OFF
Open the icemaker water
supply line shut-off valve
Move control switch to ICE
Move power switch to ON
Allow the icemaker to fill the
reservoir with water
After the gear motor starts,
move the control switch to
DRAIN
Replace the front panel
Allow the icemaker to drain
completely
Remove the front panel
Move the control switch to ICE,
replace the front panel
Allow the icemaker to run for 30
minutes or produce a batch of
ice
Remove the front panel
Move the power switch to OFF
Pour warm water into the
dispenser/storage bin to melt
any remaining ice
Clean the dispenser/storage
bin liner and cover with dish
soap and a damp cloth. Rinse
thoroughly with clean water
Move the power switch to ON,
replace the front cover
ATTENTION!
IF ICEMAKER IS ON DISPENSER,
remember to turn on the dispenser
after cleaning
AMMONIA
Cleaners
Page 2
19
20
21
22
23
24
Page 29