Hoshizaki KM-340MAH Manual page 27

Need Service or Repair? Locate your closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-rep
6
Move the M power switch to ON. Replace the Top Panel
and Front Panel § . Move the
Make ice using the cleaning solution until it stops.
§
This unit will not run until the safety switch is engaged.
M Move the control switch
7
then move the th control switch
icemaker to drain for 5 minutes.
M Move the control switch
8
momentarily, then move the
switch to ICE. Open the water supply line
shut-off valve to supply water to the
icemaker.
A After the gear motor starts, move the
9
switch to OFF, pause momentarily, then move the
control switch to DRAIN. Allow the icemaker to
drain for 5 minutes.
The icemaker might make a noise/squealing when first started due to scale removal from
auger/evaporator. This is normal in bad water conditions and will subside after 20 minutes.
M Move the control switch
10
C Close the icemaker water
11
supply line shut-off valve.
Clean Dispenser Components:
D Dilute Hoshizaki Scale Away with warm water (see
21
Table). Move the T control switch
R Remove the Front Panel and Top Panel, move the
22
switch to OFF.
Remove the Storage Bin Cover**, Bin Control R
23
Assembly (snap pin, shaft, and actuator), Spout A
B, Spout A, Spout Gaskets, Spout Cover, Ice
Dispensing Spout**, and then the Water
Dispensing Nozzle. Place in bin with cleaning
solution.
R Remove Motor Bracket Thumbscrews** first
24
from the fr vertical plane and then from
should hold the agitator or dispensing auger, while the other hand
pulls the corresponding Agitating Motor or Dispensing Motor out
the front of the icemaker. Now remove the Agitator and Dispensing
Auger from the ice storage bin and place them in the bin with
cleaning solution.
**Use a 15mm socket to easily remove thumb screws.
S Soak the parts removed in Steps 23 – 24 (except the motors) in
25
cleaning solution for 15 minutes. Rinse thoroughly with clean water.
Wipe the exterior of optical-sensors or push buttons with the cleaning solution and then a W
26
clean damp cloth. Wipe the ice shutter (located above the ice dispensing spout) thoroughly
with a clean cloth.
Continue to Sanitation – Step
DOWNLOAD COMPLETE
INSTRUCTION MANUAL:
hoshizakiamerica.com/manuals
Type in the model number of your
icemaker (including dashes) to
download manuals
#51052 | 02.21.2018
control switch to ICE.
to OFF, pause momentarily,
to DRAIN. Allow the
to OFF, pause
control
control
Listen for
Gear Motor
to OFF. Move the power switch
to OFF.
power
horizontal plane. One hand
ep to right... to
27
Dish soap, rinse well
Air Filter
Check psi, change if req'd
Water Filters
Exterior Dish soap & damp cloth
Pan/Gear Drain Clear w/ warm water + brush
Icemaker/Dispenser
Follow these instructions
Clean inlet screen/valves
Water Supply Inlet
Inspect seal bolts/ bearing
Extruding Head
wear. Tighten or replace
Water Hoses
Inspect. Replace if req'd
Tech Support: 1.800.233.1940
Make ice
with
solution
until
machine
stops
Wait it
To Icemaker
Or Water Filter
Wait
OPEN
Wait it
to Start
to OFF.
Continue to
To Icemaker Sanitation –
Or Water Filter
Step p
12
front...
SHUT OFF
DCM-751
Scale Away 9.6 fl. oz (0.29 l)
Warm Water 1.6 gal. (6.0 l)
Agitating
Motor
Dispensing
Motor
Ice
Shutter
Motor Bracket Thumbscrews
ATTENTION!
DO NOT use ammonia
type cleaners. Can
cause damage to
icemaker
WEAR liquid-proof
gloves and goggles to
protect skin & eyes
from cleaning &
sanitizing chemicals
sanitizing continued...
Move the control switch
OFF, pause momentarily, then
p
move it to ICE
Open the icemaker water
supply line shut-off valve
After the gear motor starts,
move control switch
pause momentarily, then move
it to DRAIN
Allow the icemaker to drain for
5 minutes
Move control switch
Allow the icemaker to run for
30 minutes, then clean and
sanitize the dispensing
components – Step
AMMONIA
o on
Cleaners
Sanitize Dispenser Components:
Dilute 5.25% chlorine bleach
with warm water and place it in
another bin (see Table below)
DCM-751
Bleach 0.82 fl. oz (25 ml)
Warm Water 1.6 gal. (6.0 l)
Use bleach without additives.
‡
Soak the parts removed in
Steps 23–24 (except the
motors) in sanitizing solution for
15 minutes. Rinse all the parts
thoroughly with clean water
Reassemble and replace all
parts removed in Steps 23-24
(except storage bin cover)
Pour warm water into the
storage bin to melt any
remaining ice
Clean the storage bin liner and
cover with dish soap and a damp
cloth. Rinse thoroughly with clean
water
Replace the storage bin cover
Move the power switch
then replace top and front
panels.
Move control switch
start the automatic icemaking
process
Set dispense mode switch
preference (portion or
continuous)
to
18
h
19
to OFF, F
to ICE
20
p
21
‡
27
n
29
28
30
29
4
30
r
31
to ON,
to ICE, to o
32
to
33
Page 2
Page 27