Hoshizaki KM-340MAH Manual page 23

Need Service or Repair? Locate your closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-rep
6 Using a nylon scouring pad, nylon brushes, and cleaning U
solution scrub the Storage Bin, Bin Top
Ring, Grille, Spouts A & B, Ice Chute, and Drain Pan.
†
Be sure to keep the microswitch mounted on the Bin Top dry.
Remove the clamp (if installed in Step R
7
Reservoir hose. Rinse all parts thoroughly with clean R
water before reassembling the Drip Ring, Agitator, Bin
Top, and Front & Top Panels.
Move the M control switch
8
t the electrical outlet. Move the
Make ice using the cleaning solution until it stops,
dispose of ice. Move the
ATTENTION! Icemaker might make noise/squealing when first
started due to scale being removed from auger/evaporator. This is
normal in bad water conditions and will subside after 20 min.
Cleaning Rinse:
M Move the control switch
9
switch sw to ON. Allow the icemaker to drain completely.
Move the M power switch to OFF. Unplug the icemaker
10
f from the electrical outlet. Remove the Front Panel,
Top Panel, and Bin Top.
P Pour clean, warm water into the ice Storage Bin and melt
11
any remaining ice. Remove Agitator and Drip Ring. Rinse
the inside of the Storage Bin, the Agitator, and Drip Ring
thoroughly with clean water.
P Pour clean, warm water over the Extruding Head until the
12
Evaporator Assembly and the Reservoir are full and the
water overflows into the Drain Pan.
Plug the icemaker into the electrical outlet, then move the
13
P
power switch to ON. Allow the icemaker to drain
completely.
Move the M power switch to OFF, then unplug the icemaker
14
f from the electrical outlet.
Continue to Sanitation – Step
AMMONIA
Cleaners
DOWNLOAD COMPLETE
INSTRUCTION MANUAL:
hoshizakiamerica.com/manuals
Type in the model number of your
icemaker (including dashes) to
download manuals
#51050 | 10.06.2016
†
, Agitator, Drip
) from the
to ICE. Plug the icemaker into
power switch to ON.
power switch to OFF.
to DRAIN, and the power
on front...
ENSURE ALL COMPONENTS, FASTENERS &
THUMBSCREWS ARE SECURELY IN PLACE:
Make sure that none fall into the ice storage bin
Dish soap, rinse well
Air Filter
Check psi, change if req'd
Water Filters
Dish soap & damp cloth
Exterior
Pan/Gear Drain Clear w/ warm water + brush
Icemaker/Dispenser
Follow these instructions
Clean inlet screen/valves
Water Supply Inlet
Inspect seal bolts/ bearing
Extruding Head
wear. Tighten or replace
Water Hoses
Inspect. Replace if req'd
Tech Support: 1.800.233.1940
SCRUB
Plug In
Make ice with solution until
machine stops
Wait
1 min.
Allow to Drain
Unplug
Remove Front, Top
Panels, and Bin Top
RINSE
Plug In
Allow to Drain
Unplug
ATTENTION!
ATTENTION!
DO NOT use
ammonia type
cleaners. Can cause
damage to icemaker
WEAR liquid-proof
gloves and goggles to
protect skin & eyes
from cleaning &
sanitizing chemicals
sanitizing continued...
Remove the front, top
panels, and bin top
Pour clean, warm water into
the ice storage bin to melt ice
Plug the icemaker into the
electrical outlet
Move control switch to DRAIN
Move power switch to ON
Allow to drain completely
Move power switch to
OFF
Unplug the icemaker
SANITIZE 2:
Repeat Steps 15–23 for
complete ice/food safety
Move the control switch to
ICE
Replace the front, top panels,
and bin top
Open the water supply line
shut-off valve, to supply
water back to the icemaker
Plug in the icemaker
Move the power switch to ON
Run icemaker for 30 minutes
Move the power switch to
OFF
Unplug the icemaker
Remove the front, top
panels, bin top, agitator,
and drip ring
Wipe down the ice storage bin,
bin top, agitator, drip ring, and
drain pan with a clean cloth
Move the control switch to
ICE
Reassemble all items, replace
all panels, and filter/louver
Plug in the icemaker
Move power switch to ON
21
22
23
24
25
26
27
28
29
30
Page 23