Hoshizaki KM-340MAH Manual page 25

Need Service or Repair? Locate your closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-rep
6 Move the M power switch to ON. Replace the Top Panel
†
and Front Panel . Move the
Make ice using the cleaning solution until it stops.
†
This unit will not run if the safety switch is not engaged.
Move the M control switch
7
i icemaker to drain for 5 minutes. Open the water
supply line shut-off valve to supply water to the
icemaker.
Move the M control switch
8
motor starts, move the control switch
Allow the icemaker to drain for 5 minutes.
The icemaker might make a noise/squealing
when first started due to scale removal from
auger/evaporator. This is normal in bad water
conditions and will subside after 20 minutes.
M Move the control switch
9
C Close the icemaker water
10
supply line shut-off valve.
Clean Dispenser Components:
D Dilute Hoshizaki Scale Away with warm water (see
21
Table). Move the T control switch
R Remove the Front Panel and Top Panel, move the
22
switch to OFF.
R Remove the Storage Bin Cover**, Bin Control
23
Assembly (snap pin, shaft, and actuator), Spout B, A
Spout A, Spout Gaskets, Spout Cover, Ice
Dispensing Spout**, and then the Water
Dispensing Nozzle. Place in bin with cleaning
solution.
R Remove Motor Bracket Thumbscrews** first from
24
the th vertical plane and then from
hold the agitator or dispensing auger, while the other hand pulls the
corresponding Agitating Motor or Dispensing Motor out the front of
the icemaker. Now remove the Agitator and Dispensing Auger
from the ice storage bin and place them in the bin with cleaning
solution.
**Use a 15mm socket to easily remove thumb screws.
Soak the parts removed in Steps 23 – 24 (except the motors) in S
25
cleaning solution for 15 minutes.
W Wipe the exterior of optical-sensors or push buttons with the cleaning solution and then a
26
clean damp cloth. Wipe the ice shutter (located above the ice dispensing spout) thoroughly
with a clean cloth.
Continue to Sanitation – Step
DOWNLOAD COMPLETE
INSTRUCTION MANUAL:
hoshizakiamerica.com/manuals
Type in the model number of your
icemaker (including dashes) to
download manuals
#51051 | 09.20.2017
control switch to ICE.
to DRAIN. Allow the
to ICE. After the gear
to DRAIN.
to OFF.
To Icemaker
Or Water Filter
SHUT OFF
to OFF.
power
horizontal plane. One hand should
ep to right... to
27
Dish soap, rinse well
Air Filter
Water Filters Check psi, change if req'd
Dish soap & damp cloth
Exterior
Pan/Gear Drain Clear w/ warm water + brush
Icemaker/Dispenser
Follow these instructions
Clean inlet screen/valves
Water Supply Inlet
Inspect seal bolts/ bearing
Extruding Head
wear. Tighten or replace
Water Hoses
Inspect. Replace if req'd
Tech Support: 1.800.233.1940
Make ice
with
solution
until
machine
stops
To Icemaker
Wait
Or Water Filter
5 min. .
OPEN
Listen for
Gear Motor
to Start
Continue to Sanitation –
Step p o on front...
11
DCM-300, DCM-500
Scale Away 9.6 fl. oz (0.29 l)
Warm Water 1.6 gal. (6.0 l)
Agitating
Motor
Dispensing
Motor
Motor Bracket Thumbscrews
ATTENTION!
DO NOT use
ammonia type
cleaners. Can cause
damage to icemaker
WEAR liquid-proof
gloves and goggles to
protect skin & eyes
from cleaning &
sanitizing chemicals
sanitizing continued...
Move control switch to ICE
Open the icemaker water
supply line shut-off valve
After the gear motor starts,
move control switch to DRAIN
Allow the icemaker to drain for
5 minutes
Move control switch to ICE
Allow the icemaker to run for
30 minutes, then clean and
sanitize the dispensing
components – Step p
21
AMMONIA
Cleaners
Sanitize Dispenser Components:
Dilute 5.25% chlorine bleach
with warm water and place it in
another bin (see Table below)
DCM-300, DCM-500
Bleach 0.82 fl. oz (25 ml)
Warm Water 1.6 gal. (6.0 l)
Use bleach without additives.
‡
Soak the parts removed in
Steps 23–24 (except the
motors) in sanitizing solution for
15 minutes. Rinse all the parts
thoroughly with clean water
Reassemble and replace all
parts removed in Steps 23-24
(except storage bin cover)
Pour warm water into the
storage bin to melt any
remaining ice
Clean the storage bin liner and
cover with dish soap and a damp
cloth. Rinse thoroughly with clean
water
Replace the storage bin cover
Move the power switch to ON,
then replace top and front
panels.
Move control switch to ICE, to
start the automatic icemaking
process
Set dispense mode switch to
preference (portion or
continuous)
Page 2
18
19
20
‡
27
n
29
28
30
29
4
30
N,
31
o
32
g
33
Page 25