Siemens Sinumerik 840D sl Programming Manual page 15

15 User stock removal programs .................................................................................................................725
15.1 Supporting functions for stock removal ................................................................................... 725
15.2 Generate contour table (CONTPRON).................................................................................... 726
15.3 Generate coded contour table (CONTDCON)......................................................................... 732
15.4 Determine point of intersection between two contour elements (INTERSEC) ........................ 736
15.5 Execute the contour elements of a table block-by-block (EXECTAB) ..................................... 738
15.6 Calculate circle data (CALCDAT) ............................................................................................ 739
15.7 Deactivate contour preparation (EXECUTE) ........................................................................... 741
16 Programming cycles externally ...............................................................................................................743
16.1 Technology cycles ................................................................................................................... 743
16.1.1 Introduction .............................................................................................................................. 743
16.1.2 Drilling, centering - CYCLE81 .................................................................................................. 745
16.1.3 Drilling, counterboring - CYCLE82 .......................................................................................... 746
16.1.4 Reaming - CYCLE85 ............................................................................................................... 747
16.1.5 Deep-hole drilling - CYCLE83 ................................................................................................. 748
16.1.6 Boring - CYCLE86 ................................................................................................................... 750
16.1.7 Tapping without compensating chuck - CYCLE84 .................................................................. 751
16.1.8 Tapping with compensating chuck - CYCLE840 ..................................................................... 754
16.1.9 Thread milling - CYCLE78 ....................................................................................................... 756
16.1.10 Freely programmable positions - CYCLE802 .......................................................................... 758
16.1.11 Row of holes - HOLES1 .......................................................................................................... 760
16.1.12 Grid or frame - CYCLE801 ...................................................................................................... 761
16.1.13 Circle of holes - HOLES2 ........................................................................................................ 762
16.1.14 Face milling - CYCLE61 .......................................................................................................... 763
16.1.15 Milling a rectangular pocket - POCKET3 ................................................................................. 765
16.1.16 Milling a circular pocket - POCKET4 ....................................................................................... 768
16.1.17 Rectangular spigot milling - CYCLE76 .................................................................................... 770
16.1.18 Circular spigot milling - CYCLE77 ........................................................................................... 772
16.1.19 Multiple-edge - CYCLE79 ........................................................................................................ 774
16.1.20 Longitudinal slot - SLOT1 ........................................................................................................ 776
16.1.21 Circumferential slot - SLOT2 ................................................................................................... 779
16.1.22 Mill open slot - CYCLE899 ...................................................................................................... 781
16.1.23 Elongated hole - LONGHOLE ................................................................................................. 783
16.1.24 Thread milling - CYCLE70 ....................................................................................................... 785
16.1.25 Engraving cycle - CYCLE60 .................................................................................................... 787
16.1.26 Contour call - CYCLE62 .......................................................................................................... 790
16.1.27 Path milling - CYCLE72 ........................................................................................................... 791
16.1.28 Predrilling a contour pocket - CYCLE64 .................................................................................. 794
16.1.29 Milling a contour pocket - CYCLE63 ........................................................................................ 796
16.1.30 Stock removal - CYCLE951 ..................................................................................................... 798
16.1.31 Groove - CYCLE930 ................................................................................................................ 801
16.1.32 Undercut forms - CYCLE940 ................................................................................................... 804
16.1.33 Thread turning - CYCLE99 ...................................................................................................... 807
16.1.34 Thread chain - CYCLE98 ........................................................................................................ 810
16.1.35 Cut-off - CYCLE92 ................................................................................................................... 813
16.1.36 Contour grooving - CYCLE952 ................................................................................................ 815
16.1.37 Swiveling - CYCLE800 ............................................................................................................ 819
16.1.38 High Speed Settings - CYCLE832 ........................................................................................... 822
Job planning
Programming Manual, 02/2011, 6FC5398-2BP40-1BA0
Table of contents
15