Disassembly Instructions; Control Panel Glass; Electronic Clock; Control Panel Mounting Bracket - Amana AO27DG Service Manual

Disassembly Instructions

!
WARNING

Control Panel Glass

1. Shut off power to oven.
2. Remove clock set, light switch, selector switch and
thermostat knobs. Remove four lower clock knobs
by grasping each knob and pulling knob and shaft
out of clock.
3. Remove four control panel top trim mounting
screws and remove trim.
4. Remove control panel glass by lifting it slightly up-
ward, tilting the top outward and sliding it over the
control shafts.

Electronic Clock

1. Shut off power to oven.
2. Remove control panel glass.
3. Remove four screws securing clock to control panel
mounting bracket.
4. Pull clock out of control panel mounting bracket.
Disconnect clock wiring at terminal block.

Control Panel Mounting Bracket

1. Shut off power to oven.
2. Remove control panel glass.
3. Remove four clock mounting screws. Pull clock
from control panel mounting bracket. Disconnect
clock wiring at the terminal block. Remove block.
4. Depress indicator light retaining tabs. Push indica-
tors out of control panel.
5. Remove light switch retaining nut(s). Push
switch(es) out of control panel mounting bracket.
6. Remove latch handle mounting screw. Pull latch
handle from latch lever.
7. Remove three screws securing control panel bot-
tom trim to control panel mounting bracket. Slide
trim over latch lever.
8. Remove four screws securing control panel mount-
ing bracket to oven frame.
9. Remove selector switch and thermostat mounting
screws. Slide control panel mounting bracket over
latch lever.
To avoid the risk of electric shock, personal injury or death, disconnect power To avoid the risk of electric shock, personal injury or death, disconnect power To avoid the risk of electric shock, personal injury or death, disconnect power
To avoid the risk of electric shock, personal injury or death, disconnect power To avoid the risk of electric shock, personal injury or death, disconnect power
before servicing, unless testing requires it. before servicing, unless testing requires it. before servicing, unless testing requires it. before servicing, unless testing requires it. before servicing, unless testing requires it.

Oven Light Switch

1. Shut off power to oven.
2. Remove control panel glass.
3. Remove four clock mounting screws. Pull clock out
of control panel mounting bracket.
4. Remove light switch retaining nut(s). Push
switch(es) from control panel mounting bracket.
5. Access light switch through clock opening in con-
trol panel mounting bracket. Disconnect light
switch wiring.
6. Remove switch.

Indicator Light

1. Shut off power to oven.
2. Remove control panel glass.
3. Depress indicator light retaining tabs. Push indica-
tor from control panel mounting bracket.
4. Indicator light can be reached through opening in
control panel mounting bracket and above the indi-
cator light and thermostat. Pull indicator light
through opening.
5. Disconnect indicator light wiring.
6. Remove indicator light.

Selector Switch

1. Shut off power to oven.
2. Remove control panel mounting bracket.
3. Disconnect selector switch wiring one at a time.
Reconnect to appropriate terminal on replacement
selector switch.

Oven Thermostat

1. Shut off power to oven.
2. Disconnect gas supply to oven.
3. Remove oven door and rack.
4. Slide oven slightly away from enclosure to access
capillary tube.
5. Remove capillary cover from insulation retainer.
6. Remove two screws securing thermostat bulb
shield to inner oven side wall. Slide shield off ther-
mostat bulb.
7. Unscrew thermostat capillary hole cover retaining
screw. Remove cover.
8. Remove control panel glass. Remove control panel
mounting bracket.
9. Disconnect thermostat wiring one lead at a time.
Reconnect to appropriate terminal on replacement
thermostat.
10. Pull capillary tube out of oven cavity. Remove ther-
mostat and capillary tube assembly.
31 RA233001 Rev. 3