Panasonic PT-RS30K Service Manual page 8

PREFACE
f When using the projector at an altitude between 2 700 m (8 858') and 4 200 m (13 780') above sea level: 25 °C (77 °F)
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [LONG LIFE1], [LONG LIFE2], or [LONG
LIFE3], and the operating environment temperature exceeds 35 °C (95 °F), the light output may be reduced to protect the projector.
Note
f The light output will decrease to approximately 1/3 when using the projector with AC 100 V to AC 120 V.
f The model numbers of accessories and optional accessories are subject to change without prior notice.
2.2. Terminals
r Terminal
<RGB 1 IN> terminal
<RGB 2 IN> terminal
<DVI-D IN> terminal
<HDMI IN> terminal
<SDI IN 1> terminal
<SDI IN 2> terminal
<MULTI PROJECTOR SYNC
IN> terminal/<3D SYNC 1 IN/
OUT> terminal (dual purpose)
<MULTI PROJECTOR SYNC
OUT> terminal/<3D SYNC 2
OUT> terminal (dual purpose)
<SERIAL IN>/ <SERIAL OUT>
terminal
<REMOTE 1 IN>/ <REMOTE 1
OUT> terminal
<REMOTE 2 IN> terminal
<DIGITAL LINK/LAN> terminal
<DC OUT 1> terminal/<DC
OUT 2> terminal
234 - ENGLISH
Chapter 7 Appendix — Specifications
1 set (BNC x 5 (RGB/YP P /YC
B R
RGB signal 0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
SYNC/HD
VD
YP P signal
Y: 1.0 V [p-p] including synchronization signal, P
B R
Y/C signal Y: 1.0 V [p-p], C: 0.286 V [p-p] 75 Ω
VIDEO signal 1.0 V [p-p] 75 Ω
1 set, high-density D-Sub 15 p (female)
RGB signal 0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
SYNC/HD
VD
YP P signal Y: 1.0 V [p-p] including synchronization signal, P
B R
1 set, DVI-D 24 p, single link, DVI 1.0 compliant, HDCP compatible
1 set, HDMI 19 p, HDCP compatible, Deep Color compatible
1 set (BNC)
SD-SDI signal
SMPTE ST 259 compliant
HD-SDI signal SMPTE ST 292 compliant
3G-SDI signal SMPTE ST 424 compliant
Dual link HD-SDI
SMPTE ST 372 compliant
(LINK-A) signal
Dual link 3G-SDI (Link
SMPTE ST 425 compliant
1) signal
1 set (BNC)
SD-SDI signal SMPTE ST 259 compliant
HD-SDI signal
SMPTE ST 292 compliant
3G-SDI signal SMPTE ST 424 compliant
Dual link HD-SDI
SMPTE ST 372 compliant
(LINK-B) signal
Dual link 3G-SDI (Link
SMPTE ST 425 compliant
2) signal
1 set (BNC)
TTL high impedance
When [3D SYNC MODE] is set to output, TTL output: Maximum 10 mA
1 set (BNC)
TTL output: Maximum 10 mA
D-Sub 9 p, 1 set each, RS-232C compliant, for computer control
M3 stereo mini jack, 1 set each, for remote control (wired)/for projector connection control
1 set, D-Sub 9 p, for contact control
1 set, RJ-45, for network and DIGITAL LINK connections (HDBaseT
100Base-TX, Art-Net compatible, HDCP compatible, Deep Color compatible
2 sets, USB connector (type A), for power supply only (DC 5 V, maximum 900 mA for each terminal)
C /YC/VIDEO x 1))
B R
TTL high impedance, automatic positive/negative
polarity compatible
TTL high impedance, automatic positive/negative
polarity compatible
TTL high impedance, automatic positive/negative
polarity compatible
TTL high impedance, automatic positive/negative
polarity compatible
8
<RZ31K/RS30K>
P : 0.7 V [p-p] 75 Ω
B R
P : 0.7 V [p-p] 75 Ω
B R
compliant), PJLink compatible,
TM