Panasonic PT-RS30K Service Manual page 58

SECTION 1 SERVICE INFORMATION
Bit Error code (hex)
199 00000000 00000080
200 00000000 00000100
201 00000000 00000200
202 00000000 00000400
203 00000000 00000800
204 00000000 00001000
205 00000000 00002000
206 00000000 00004000
207 00000000 00008000
208 00000000 00010000
209 00000000 00020000
210 00000000 00040000
211 00000000 00080000
212 00000000 00100000
213 00000000 00200000
214 00000000 00400000
215 00000000 00800000
216 00000000 01000000
217 00000000 02000000
218 00000000 04000000
219 00000000 08000000
220 00000000 10000000
221 00000000 20000000
222 00000000 40000000
223 00000000 80000000
224 00000001 00000000
225 00000002 00000000
226 00000004 00000000
227 00000008 00000000
228 00000010 00000000
229 00000020 00000000
230 00000040 00000000
231 00000080 00000000
232 00000100 00000000
233 00000200 00000000
234 00000400 00000000
235 00000800 00000000
236 00001000 00000000
237 00002000 00000000
238 00004000 00000000
239 00008000 00000000
240 00010000 00000000
241 00020000 00000000
242 00040000 00000000
243 00080000 00000000
244 00100000 00000000
245 00200000 00000000
246 00400000 00000000
247 00800000 00000000
248 01000000 00000000
249 02000000 00000000
250 04000000 00000000
251 08000000 00000000
252 10000000 00000000
253 20000000 00000000
254 40000000 00000000
255 80000000 00000000
l How to read the returned value and the self-diagnosis serial control command.
Use the command "QVX:ERRS1" to get the information of Self-diagnosis for this model.
The returned value provides the 255bit self-diagnosis information as follows.
(Table below shows no error occurs)
255 • • • •
ERRS1= N • • • •
The returned value "N" indicates normal and "E" indicates error status. The first bit 0 starts from right and it ends by 255th bit
at left.
Example: If the self-diagnosis information is inquired under the condition of the projection lens un-mounted, the "E" will ap-
pear on 70th bit as the below.
255 • • • •
ERRS1= N • • • •
Self-test indica-
Details
tion
Power CPU communication error
FC0
GEOMETRY communication error
F97
FRC error
FC2
FM-R TEST Fail
F81
FM-G TEST Fail
F82
FM-B TEST Fail
F83
LD1-B Sub CPU error
F65
LD1-S Sub CPU error
F66
LD2-B Sub CPU error
F67
LD2-S Sub CPU error
F68
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
－ Not used
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
IIC communication error 1 (RTC)
A41
IIC communication error 2 (EEPROM)
A42
IIC communication error 7 (EDID DIGITAL)
A47
IIC communication error 7 (EDID ANALOG)
A48
IIC communication error 9 (ADC1)
A49
IIC communication error 10 (ADC2)
A50
IIC communication error 11 (ACCELERATION SENSOR)
A51
IIC communication error 12 (OPTICAL SENSOR)
A52
IIC communication error 13 (HD BaseT)
A53
IIC communication error 14 (ATM SENSOR)
A54
Sub CPU communication error (R8)
A08
FM communication error
A97
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
Not used
－
bit
200 • • • • 150 • • • •
N • • • • N • • • •
bit
200 • • • • 150 • • • •
N • • • • N • • • •
Probable cause
Communication error on Power CPU
Communication error on Geometry IC
Program transferring error to FRC
Abnormal on FM startup mode
Error on FM memory test
Divice operation error on DR-PCB
Divice operation error on Signal PCB
Communication error on Sub CPU
Communication error on FM
100 • • • • 50 • • • •
N • • • • N • • • •
100 • 70 • • 50 • • • •
N • E • • N • • • •
"E" will appear on 70th bit.
INF-48
1 0
N N
1 0
N N
<RZ31K/RS30K>