Panasonic PT-RS30K Service Manual page 24

SECTION 1 SERVICE INFORMATION
2. 3DCMS
• Setting of the 3D Color Management System operation.
- ON : Enable the 3D Color Management system function. (Default setting)
- OFF : Disable the 3D Color Management system function.
3. SELF CHECK
• Self-diagnosing information Displays.
SELF CHECK
MODEL
①
SERIAL NO.
②
---------- VERSION --------------
MAIN
③
SUB
④
DIGITAL LINK : 1.30.20.5
⑤
FPGA
⑥
CPLD
⑦
FM(R)
⑧
FM(G)
FM(B)
LD DRIVER
⑨
SELF CHECK
LD SUB
⑩
FRC
⑪
⑫ POWER
---------- DEVICE CHECK ----------
OK : AIR TEMP 123/456
⑬
⑭ OK : DMD TEMP 123/456
⑮ OK : OUT TEMP 123/456
⑯ OK : AIR FLOW 123/456/789
⑰ OK : LD1B TEMP 123
⑱ NG : LD1S TEMP 123
⑲
OK : LD2B TEMP 123
⑳
OK : LD2S TEMP 123
SELF CHECK
㉑
OK : FPGA TEMP 123
㉒
OK : LD1B 1 *
㉓
OK : LD1S 1 0
㉔
OK : LD2B 1 1 1 1 1 1
㉕
OK : LD2S 1 1 1 1 1 1
㉖
NG : FAN[1] 1111
㉗
OK : FAN[2] 1111 1111 1111 1111 1
㉘
OK : PHOTO Y 123456.7
㉙
OK : ATM 1234/567
㉚
OK : ANGLE H -123.4/ V +123.4
㉛
OK : SHUTTER 65535 [
㉜
[Note]
• Items to indicates the status of "NG" or "OK". If the "NG" indicates in red, the projector has an abnormality now. If the
⑬ ㉜
"OK" indicates in red, the projector had an abnormality in the past and operates normally now.
• To clear the error status, press the [MENU] key in the SELF CHECK mode, the confirmation window will appear and select
[OK] to clear.
• This must be done after finishing the repair or maintenance.
: RZ31K
: SW1234567890
: 1.00.00
: 1.00.00
: 01.01/02.02/03.03
: 01.01
: 00.0400.00
: 00.0400.00
: 00.0400.00
: 01.00/01.00/01.00/01.00
DEVICE CHECK : OK
: 01.00/01.00/01.00/01.00
: 1.00.00
: 1.00.00
DEVICE CHECK :
0 1 1 1
1 1 1 *
1110 1111 1111 1111
0]
DEVICE CHECK :
CLEAR ERROR INFOMATION?
OK
① – Model name
1/3
② – Serial no.
------------------- VERSION-----------------------------
③ – Main CPU firmware version
④ – Sub CPU firmware version
⑤ – Digital Link firmware version
⑥ – Digital Link firmware version
⑦ – FPAG firmware version
⑧ – (R/G/B) Formatter firmware version
⑨ – LD driver (LD1B/LD1S/LD2B/LD2S) firmware version
⑩ – LD Sub driver firmware version
2/3
⑪ – FRC firmware version
⑫ – Power firmware version
------------------- DEVICE CHECK-----------------------------
⑬ – Intake air temperature (Celsius/Fahrenheit)
⑭ – DMD temperature (Celsius/Fahrenheit)
⑮ – Exhaust air temperature (Celsius/Fahrenheit)
⑯ – Airflow sensor
tion value)
⑰ – LD1B temperature (Celsius)
⑱ – LD1S temperature (Celsius)
⑲ – LD2B temperature (Celsius)
⑳ – LD2S temperature (Celsius)
NG
3/3
– FPGA temperature (Celsius)
㉑
– LD1B check (1: normal / 0: abnormal / *: intentional Off)
㉒
– LD1S check (1: normal / 0: abnormal / *: intentional Off)
㉓
– LD2B check (1: normal / 0: abnormal / *: intentional Off)
㉔
– LD2S check (1: normal / 0: abnormal / *: intentional Off)
㉕
– Fan[1] check (1: normal / 0: abnormal)
㉖
㉗ – Fan[2] check (1: normal / 0: abnormal)
㉘ – Luminance sensor check (detected value)
㉙ – Atmospheric pressure sensor check
value/Temperature detected value)
– Angle sensor check (Horizontal angle / Vertical angle)
㉚
– Shutter control check (Opening and shutting times
㉛
[Failure times])
NG
㉜ – Device check (OK: Normal, NG: abnormal)
CANCEL
INF-14
<RZ31K/RS30K>
(Sensor value/AD conversion value/Correc-
(Sensor detected