Panasonic PT-RS30K Service Manual page 46

Light source/temperature/filter indicators
SECTION 1 SERVICE INFORMATION
When an indicator lights up
5. Troubleshooting
If a problem occurs inside the projector, the light source indicators <LIGHT1>/<LIGHT2>, temperature indicator
<TEMP>, or filter indicator <FILTER> will inform you by lighting or blinking in red. Check the status of the
5. 1. Power/Light/temperature/filter indicators
indicators and take following measures.
Attention
• If a problem occurs inside the projector, each indicators will inform you by lighting or blinking.
f When switching off the projector to deal with problems, make sure to follow the procedure in "Switching off the projector" .
Power indicator <ON(G)/STANDBY(R)>
Light source indicators <LIGHT1>/<LIGHT2>
Power indicator <ON(G)/STANDBY(R)>
Indicator status
f Some of the elements of the light
Lighting in red source are defective and the light
output has decreased.
Indicator status
f The light source is turned off since
Blinking in red
Off
the projection lens cannot be
(1 time)
detected.
Blinking in red Red
f The light source does not light up,
(2 times)
or the light source turns off while the
Blinking in red
projector is in use.
Green
(3 times)
Orange
Note
Note
f If the light source indicators <LIGHT1>/<LIGHT2> are still lit or blinking after taking the measures, set the <MAIN POWER> switch to
<OFF>, and ask your dealer for repairs.
f While the power indicator <ON (G)/STANDBY (R)> lights in orange, the fan is running to cool the projector.
f The light source indicator corresponding to the light source being lit will light up in green if the projector is in projection mode and there is no
f For approximately 15 seconds after the projector is switched off, the indicator does not light up even if the power is switched on. Turn on the
indication of problem by lighting or blinking in red.
power again after the power indicator <ON (G)/STANDBY (R)> lights in red.
f The projector consumes power even in standby mode (power indicator <ON (G)/STANDBY (R)> lit in red). Refer to "Power consumption"
for the power consumption.
f When the projector receives the signal from the remote control, the power indicator <ON (G)/STANDBY (R)> will blink in the following color
according to the status of the projector.
g When the projector is in projection mode: Green
g When the projector is in standby mode: Orange
However, if the [PROJECTOR SETUP] menu → [STANDBY MODE] is set to [ECO], the indicator will stay lit in red and will not blink if the
projector is in standby mode.
f The power indicator <ON (G)/STANDBY (R)> will blink slowly in green while the shutter function is in use (shutter: closed), or while the
function of the [PROJECTOR SETUP] menu → [NO SIGNAL LIGHTS-OUT] is operating and the light source is turned off. f If the power
indicator <ON (G)/STANDBY (R)> is blinking in red, consult your dealer.
Light source indicator <LIGHT1>
Status
f Turn the <MAIN POWER> switch to <OFF> , and turn on the
power again.
f Turn off the power and mount the projection lens again.
The main power is switched off.
f Turn the <MAIN POWER> switch to <OFF> , and turn on the
The power is switched off. (standby mode)
power again.
Projection will start when the power on <b> button is pressed.
Lit
f The projector may not operate when the light source indicators <LIGHT1>/<LIGHT2>
f Turn the <MAIN POWER> switch to <OFF> , and turn on the
or the temperature indicator <TEMP> are blinking.
power again.
Lit Projecting.
The projector is preparing to switch off the projector.
Lit
The power is switched off after a while. (Changes to the standby mode.)
Light source indicator <LIGHT2>
Temperature indicator <TEMP>
Filter indicator <FILTER>
Solution
Projector status
INF-36
<RZ31K/RS30K>
ENGLISH - 193