Trane CVHH Installation, Operation And Maintenance Manual page 12

Pre-Installation
WARNING
Combustible M aterial!
Failure to follow this instruction could result in death or
serious injury or equipment damage. Shrink-w rap is a
combustible material. Avoid open flames and hot
sparks.
Type of Tr a n e Su pplie d
Re qu ir e m e n t Tr a ne I nst a lle d
Foundat ion
Rigging
Disassem bly/ Reassem bly •
( as required) direct on- sit e supervision of
t he disassem bly and
reassem bly work ( cont act
your local Trane office for
pricing)
I solat ion
Elect rical •
disconnect s ( opt ional)
•
( opt ional)
•
Wat er piping
Relief •
•
I nsulat ion •
Wat er Piping Connect ion Flanged ( opt ional)
Com ponent s
•
2068.4 kPag ( 300 psig)
wat erboxes
Ot her Mat erials
12
Tr a ne Su pplie d
Fie ld I nst a lle d
Trane will perform or have
•
isolat ors
Circuit breakers or fusible •
•
Unit m ount ed st art er ( opt ional out door air)
•
PFCCs ( opt ional) field supplied)
•
( opt ional)
•
( m ay be field supplied)
Rupt ure disk assem bly
Rupt ureGuard™ ( opt ional)
I nsulat ion ( opt ional)
Flanged ( opt ional)
Welded on flange for •
adapt er for 1034.2 kPag
( 150 psig) wat erboxes
N ot e: The chiller should rem ain w ithin its protective
shrink-w rap covering during storage.
Fie ld Supplie d
Fie ld I nst a lle d
• Meet foundat ion requirem ent s
• Safet y chains
• Clevis connect ors
• Lift ing beam
I solat ion pads or spring • I solat ion pads or spring isolat ors
Jum per bars • Circuit breakers or fusible disconnect s ( opt ional)
Tem perat ure sensor • Elect rical connect ions t o unit m ount ed st art er
( opt ional)
Flow sw it ches ( m ay be • Elect rical connect ions t o rem ot e m ount ed st art er
( opt ional)
Rem ot e- m ount ed st art er • Wiring sizes per subm it t al and NEC or local codes
• PFCCs ( rem ot e m ount ed st art er opt ional only)
• Term inal lugs
• Ground connect ion( s)
• Jum per bars
• BAS w iring ( opt ional)
• I PC wiring ( AFD and rem ot e- m ount ed st art ers only)
• Cont rol volt age wiring ( AFD and rem ot e- m ount ed
st art ers only)
• Oil pum p int erlock wiring ( AFD and rem ot e m ount ed
st art ers only)
• High condenser pressure int erlock wiring ( AFD and
rem ot e m ount ed st art ers only)
• Chilled wat er pum p cont act or and wiring including
int erlock
• Condenser wat er pum p cont act or and wiring includin g
int erlock
• Opt ion relays and wiring
Flow sensing devices • Taps for flow sensing devices
• Taps for t herm om et ers and gauges
• Therm om et ers
• St rainers ( as required)
• Wat er flow pressure gauges
• I solat ion and balancing valves in wat er piping
• Vent s and drain on wat erbox valves ( one each per p ass)
• Pressure relief valves ( for wat erboxes as required )
• Vent line and flexible connect or and vent line fro m
rupt ure disk t o at m osphere
• I nsulat ion
• Chiller feet insulat ion
Vict aulic
®
Vict aulic t o flange • Vict aulic coupling for 1034.2 kPag ( 150 psig) and
2068.4 kPag ( 300 psig) wat erboxes
• Fast eners for flanged- t ype connect ions ( opt ional)
• Mat erial and equipm ent t o perform leak t est ing
• Dry nit rogen ( 55.2 kPag [ 8 psig] m axim um per
m achine as needed)
CVHH-SVX001A-EN