Biasi Inovia 25S ERP User Manual And Installation Instructions
  1. Manuals
  2. Brands
  3. Biasi Manuals
  4. Boiler
  5. Inovia 25S ERP
  6. User manual and installation instructions
Biasi Inovia 25S ERP User Manual And Installation Instructions

Biasi Inovia 25S ERP User Manual And Installation Instructions

Wall hung, fanflue, roomsealed, high efficiency gas boiler
Hide thumbs Also See for Inovia 25S ERP:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual
Wall hung, fanflue, roomsealed, high efficiency gas boiler
User manual and

Installation instructions

Inovia ERP
Models
Inovia 25S ERP
G.C. Appl. No.
41-583-30
SYSTEM BOILER

Advertisement

Table of Contents
loading

Related Manuals for Biasi Inovia 25S ERP

Summary of Contents for Biasi Inovia 25S ERP

  • Page 1: Installation Instructions

    Wall hung, fanflue, roomsealed, high efficiency gas boiler User manual and Installation instructions Inovia ERP Models G.C. Appl. No. Inovia 25S ERP 41-583-30 SYSTEM BOILER...
  • Page 2 This allows a gain of useful heat that otherwise would be lost. Biasi UK Ltd is a licensed member of the Benchmark Scheme which aims to improve the standards of installation and commissioning of domestic heating and hot water systems in the UK and to encourage regular servicing to optimise safety, efficiency and performance.
  • Page 3 Remember that... The manual must be read thoroughly, so that you will be able to use the boiler in a safe and sensible way and must be carefully kept. It may be necessary for reference in the future. The first firing must be carried out by a competent and responsible Gas Safe engineer. The manufacturer •...
  • Page 4 Safe handling of substances Biasi products are manufactured in accordance with ISO 9001 and do not, and will not, contain any hazardous materials or substances such as asbestos, mercury or C.F.C.’s. The appliance packaging does not contain any substances, which may be considered a hazard to health.
  • Page 5 Combustion chamber panels Material: mineral fibres Known hazards - Some people can suffer reddening and itching of the skin. Fibre entry into the eye will cause foreign body irritation, which can cause severe irritation to people wearing contact lenses. Irritation to respiratory tract. Precautions - Dust goggles will protect eyes.

  • Page 6: Installing The Boiler

    If you are in any doubts as to the installation or operation of the boiler please read the instruction manuals thoroughly and then if necessary contact Biasi UK for advice and as- sistance.

  • Page 7: Table Of Contents

    9 GAS CONVERSION ....67 Technical data Inovia 25S ERP ... . . 28 Warnings .

  • Page 8: Appliance Description

    APPLIANCE DESCRIPTION APPLIANCE DESCRIPTION Isolation valves Overview The model and serial number of the boiler is shown on the bottom of the boiler. Fig. 1.2 2 Gas supply label 3 C.H. flow valve Fig. 1.1 4 Gas inlet valve 1 Controls panel 5 C.H.

  • Page 9: Control Panel

    APPLIANCE DESCRIPTION Control panel RESET that takes all parameters back to the factory value occurs only setting "parameter 08=04". Reset is displayed by switch on of all symbols present on the display. Press keys 14 and 18 (Fig. 1.3) simultaneously for 5 seconds in order to reset all the scheduling (both preheating and heating).
  • Page 10 APPLIANCE DESCRIPTION Flashing: All symbols repre- solar circuit pump in sented with lines that operation. surround them, indi- Solar integration at cate that the symbol the time of D.H.W. is flashing. withdrawal is indicat- ed by the lighting of Constantly illuminat- the bars.
  • Page 11 APPLIANCE DESCRIPTION SIGNAL DISPLAYED BY THE LCD Constantly illumi- nated: lockout error. FUNCTION The boiler can be Lack of burner ignition restarted by the user on safety lockout. by pressing the reset Safety thermostat inter- button. vention lockout. Non resettable error. General lockout.
  • Page 12 APPLIANCE DESCRIPTION FUNCTION FUNCTION Wiring error lockout. Boiler requesting heat- ing power and remote Failure of the solar con- control connected. troller. Set C.H. Boiler not configured. (all other symbols are disabled). Primary circuit temp. L 01 limit during D.H.W. op- eration.

  • Page 13: Instructions For Use

    Warnings If you are in any doubt regarding this procedure you are advised to contact Biasi UK Ltd support the Benchmark your Installer or an Approved Engineer. initiative. The Benchmark Checklist is located at the back of this manual and...

  • Page 14: Ignition

    INSTRUCTIONS FOR USE If you experience any difficulty with the operation of the boiler, switch off the Stand-by boiler immediately at the fused spur iso- Hyphens are turned lation switch and contact your Installer on in sequence to or an approved Service Engineer. simulate running Air introduced into the boiler during this fill- ing process will vent through the automatic...

  • Page 15: Circuit Temperature

    INSTRUCTIONS FOR USE To exit programming, hold down key 18 for • The heating flow "set" temperature and 5 seconds (all changes will be saved) or the symbol flash. The background wait 60 seconds. of the display is illuminated (Fig. 2.9). NOTE: If a remote is connected, the card acquires the time, date and year data from the remote itself, and synchronises with it...
  • Page 16 INSTRUCTIONS FOR USE To set the time brackets: the temperature of the C.H. system water N.B.: You must have first set the current flow in relation to the external temperature. In this case the boiler must be set by a qual- time and date.
  • Page 17 INSTRUCTIONS FOR USE which take you back to the Time Bracket To exit programme, hold down Key 13 for 5 which will be flashing to set use key’s 17 seconds or wait 60 seconds. or 16. To confirm once time has been set press N.B.: If you re-enter the programming mode key 18 then 13 to exit back to the day/group and modify the time settings your new val-...

  • Page 18: Switching Off

    INSTRUCTIONS FOR USE Activation: N.B.: The following settings are also reset Press keys 16 and 17 (Fig. 2.16) at the along with the time bracket. same time for 2 seconds to enter pro- gramme menu (Fig. 2.17). Deactivation / End of function: The function programme will end when the time set passes in our example 1 day or when the function status is manually set to...
  • Page 19 INSTRUCTIONS FOR USE Fig. 2.23 If a long period of inactivity is envisioned: • Switch off the electricity supply to the boil- er, by means of the fused spur isolation switch. • Shut off the gas supply cock and the valves for the water circuits fitted under the boiler Fig.

  • Page 20: Useful Advice

    USEFUL ADVICE USEFUL ADVICE Therefore, when the boiler is not lit and used in cold weather, with consequent risk Central Heating of freezing do not switch off the boiler at the fused spur isolation switch or close the gas For your comfort and added system control, inlet cock.

  • Page 21: External Cleaning

    USEFUL ADVICE tion. plugged drain pipe). It is advisable to check the condensate drainage pipe and traps for Please refer to the servicing information on cleanness. section "MAINTENANCE" on page 69. Press the reset key 14 on the boiler control panel (Fig.

  • Page 22: Displaying In Info Mode

    USEFUL ADVICE be done very frequently, have the system checked for leaks. Water comes out of the pressure relief valve Check on the pressure gauge that the pres- sure in the central heating circuit is not close to 3 bars. In this case, temperature rise in the circuit can cause the pressure relief valve to open.

  • Page 23: Remote Anomaly Code

    USEFUL ADVICE Flue probe D.H.W. capacity ---- The flue probe 21 and safety thermal fuse Flue temperature (if fore- J11 + value 26 indicated in Fig. 3.7 are a safety device. seen) The flue probe 21 intervenes when the flue Fan speed (if foreseen) J12 + value temperature exceeds 110°C placing the...

  • Page 24: Technical Information

    TECHNICAL INFORMATION TECHNICAL INFORMATION Overview 32 31 Fig. 4.1 - 24 -...

  • Page 25: Main Diagram

    TECHNICAL INFORMATION Main diagram Fig. 4.2 3 C.H. flow valve 23 Condensing heat exchanger 4 Gas inlet valve 24 Safety thermostat 5 C.H. return valve 25 Flame-detecting electrode 7 Condensate drain pipe 26 Safety thermal fuse 8 Main circuit drain valve 27 Air manifold 28 C.H.
  • Page 26 TECHNICAL INFORMATION 33 Control box containing: External temperature probe terminal block, remote terminal block, power supply terminal block, external controls terminal block 34 Primary circuit pressure switch 35 Condensate trap 36 Fan 37 Air box (air/gas mixer) 38 Ignition electrode 39 Burner 40 C.H.

  • Page 27: Hydraulic Specifications

    TECHNICAL INFORMATION Hydraulic specifications Expansion vessel The hydraulic specifications represents the Note: this boiler is designed for opera- pressure (available head for the central tion only in a sealed central heating sys- heating system) as a function of the flow tem.

  • Page 28: Technical Data Inovia 25S Erp

    TECHNICAL INFORMATION Technical data Inovia 25S ERP Heat input Central heating 25,0 Min/Max flow temperature settings* °C 25 - 85 Nominal net central heating BTU/h 85304 Maximum pressure 27,8 Nominal gross central heating BTU/h 94687 Minimum pressure Minimum net BTU/h 20473...
  • Page 29 TECHNICAL INFORMATION Ø mm Flue gas figures Gas restrictors references /100 Nominal heat input 25,0 (A) (E) Natural G20 content with gas G20 9,0 -9,8 Propane G31 content with gas G20 Air/gas mixer restrictors CO content with gas G20 238,0 Natural G20 Fuchsia Exhaust temperature...
  • Page 30 TECHNICAL INFORMATION Model(s): Inovia 25S ERP Condensing boiler: Low-temperature boiler (**): B1 boiler: Cogeneration space heater: If yes, equipped with a supplementary heater: Combination heater: Item Symbol Value Unit Item Symbol Value Unit Seasonal space heating Rated heat output η...

  • Page 31: General Requirements

    GENERAL REQUIREMENTS GENERAL REQUIREMENTS Related documents The installation of this appliance must be in accordance with the relevant requirements of the current Gas Safe (Installation & Use) Regulations, the Local Building Regulations, the current I.E.E. Wiring Regulations, the Regulations and by-laws of the local water un- Benchmark places responsibilities on both dertaking, and in Scotland, in accordance with manufacturers and installers.

  • Page 32: Flue System

    GENERAL REQUIREMENTS guidance on this aspect. A compartment used to enclose the appliance must be designed specifically for this purpose. This appliance is not suitable for external installation. Flue system The provision for satisfactory flue termination must be made as described in BS 5440 part 1. For Ireland (IE), refer to I.S.813.2002.

  • Page 33: Gas Supply

    GENERAL REQUIREMENTS Minimum dimensions Symbol Location position (mm) Directly below an opening, air brick, opening window, etc. Above an opening, air brick, opening window, etc. Horizontally to an opening, air brick, opening window, etc. Below temperature-sensitive building components, e.g. D ** plastic gutter soil pipes or drain pipes E ** Below eaves...

  • Page 34: Air Supply

    GENERAL REQUIREMENTS Air supply If a part of the drainpipe runs externally this part should be kept as short as possible and The room in which the boiler is installed does protected to reduce the risk of freezing. not require a purpose provided air vent. Connection of condensate drainage pipe to internal soil and vent stack.

  • Page 35: Water Circulation (C.h.)

    GENERAL REQUIREMENTS Water circulation (C.H.) • A WRAS approved dry trap such as the Te- sla DTUN 1522 is utilised. Detailed recommendations are given in BS • That the condensate is connected down- 6798, BSEN 12828: 2003, BSEN 12831: 2003 stream of the trap as shown in the drawing &...

  • Page 36: Water Treatment

    GENERAL REQUIREMENTS cilitate complete filling of the system. with either plastic or copper pipes, it is impor- tant the system is fully flushed, on completion, Expansion vessel to ensure flux residues, swarf, oils and other The appliance has an integral sealed expan- installation debris is removed.

  • Page 37: Installation

    INSTALLATION INSTALLATION drain must be connected to a suitable drain, or discharged in a safe manner. Warnings The electrical wiring must conform with cur- The use of gas appliances is sub- rent Regulations, in particular: ject to statutory control; it is es- sential to observe the current •...

  • Page 38: Installing The Bracket

    We recommend the use of a suitable Build- cert approved universal inhibitor to protect the C.H. system from corrosion. Biasi UK strongly recommend that matched - 38 -...

  • Page 39: Overall Dimensions

    INSTALLATION Overall dimensions Joints The boiler respects the following dimensions: The boiler uses the following fittings: Pipe sizes Functions Ø80 Ø80 Ø80 (o.d) Gas, C.H. return, C.H. flow Ø 22 mm Ø100 Pressure relief valve Ø 15 mm Ø 25 mm Condensate drain (rubber) sizes in mm o.d.

  • Page 40: Fitting The Flue System

    INSTALLATION The terminal must be higher than the boiler. The following kits to be connected to the boiler are available: Wall flue exhaust kit (Fig. 6.6 A) This kit allows the flues to be exhausted in the rear wall or at the side of the boiler. Fig.
  • Page 41 INSTALLATION Additional bends at 45° or 90° (Fig. 6.6 C) Type C Coaxial bends Ø 60/100 mm. 90° These bends when used with the pipe reduce the maximum length of the flue pipe by: For the bend of 45° loss 0.5 m 45°...
  • Page 42 INSTALLATION Coaxial Ø 60/100 mm (b) + vertical part Ø 60 mm (a) Telescopic coaxial flue 0.45-0.95 m Maximum length (a + b) 15 m 90° =--- 0,85 m This kit allows the products of combustion to ø 60 mm be discharged at a different location to the air intake to avoid nuisance issues.

  • Page 43: Electric Connection

    INSTALLATION A Plume deflector is available to assist in over- • Identify the terminal block cover lid "O" (Fig. coming boundary nuisance issues. 6.15) and open it. Fig. 6.13 Electric connection • Unscrew screws "M" and remove the front panel "N" by pulling it and pushing it towards the top so that it is freed from the top hous- ing Fig.

  • Page 44: Connecting The Room Thermostat Or Zone Valves

    INSTALLATION Remote External Probe Electric Fig. 6.18 power supply 6.10 Connecting the room thermo- stat or zone valves Ambient Use the clamps indicated in Fig. 6.16 to con- thermostat nect the ambient thermostat. Remove the electric jumper present be- Fig. 6.16 tween “1 and 3”...
  • Page 45 INSTALLATION Connecting the zone valves controlled by Room thermostat the ambient thermostat (230V rating) Ambient Thermostat Fig. 6.20 Room thermostat with delay resistor Zone valve (230V rating) with micro contact Fig. 6.22 Ambient Thermostat Fig. 6.21 The thermostat must be insulation class II ( ) or must be correctly connected to earth.

  • Page 46: External Frost Protection

    INSTALLATION Use the ambient thermostat's clamps indicat- Press keys 16 or 17 to exit without changing ed in Fig. 6.16 and Fig. 6.17 to connect the the value. zone valve Insert the electric cables of the zone valve's micro switch contacts in clamps “1 and 3”...

  • Page 47: Connecting A System Boiler To A Cylinder

    INSTALLATION Do not connect live wires to terminals to Frost Thermostat which the frost thermostat must be con- (230V rating) nected. Room thermostat (230V rating) Frost Thermostat (230V rating) Room thermostat (230V rating) Fig. 6.29 If the external control is connect- ed with live wires (Fig.
  • Page 48 INSTALLATION is controlled by the external control terminal block. In Fig. 6.31 the boiler is not permanently con- nected to the supply line. The boiler operation is controlled by switching the mains supply. In this case, when the boiler is switched off some important features like the antifreeze system, the monitoring of the boiler by the op- eration lights, the post circulation of the pump,...
  • Page 49 INSTALLATION Cylinder Room thermostat thermostat GRYE Electric supply Room thermostat Frostat terminal block HW ON HW OFF MAINS Programmer 230V a.c. Switched 3 Amp fused, spur Mid- position diverter valve GRYE Room thermostat Cylinder thermostat 10 way junction box MAINS 230V a.c.
  • Page 50 INSTALLATION Cylinder Room thermostat thermostat GRYE Electric supply Room thermostat Frostat terminal block HW ON HW OFF MAINS Programmer 230V a.c. Switched 3 Amp fused, spur Mid--- position diverter valve GRYE Room thermostat Cylinder thermostat 10 way junction box MAINS 230V a.c.

  • Page 51: Installation Of The External Temperature Probe

    INSTALLATION 6.13 Installation of the external tem- perature probe (optional) The external probe must be installed on the external wall of the building avoiding: • Direct sunlight. • Humid walls or walls subject to the formation Remote of mildew. • Installation near to fans, drain outlets or chimneys.

  • Page 52: Example Of Hydraulic Systems With Hydraulic

    INSTALLATION Hydraulic system examples relevant cable clamps "P" (Fig. 6.18). Top zone + low temperature zone. 6.16 Example of hydraulic systems with hydraulic separator External probe (optional) The hydraulic separator creates a reduced load loss zone that renders the primary circuit and secondary circuit hydraulically independ- ent.

  • Page 53: Commissioning

    COMMISSIONING COMMISSIONING Warnings The commissioning of this boiler and sys- tem must only be undertaken by a Gas Safe Registered Engineer in accordance with the requirements of the Gas Safe In- stallation and Use Regulations and be ap- proved by Gas Safe. Ensure that the Benchmark Checklist is satisfactorily completed during the com- missioning process.
  • Page 54 COMMISSIONING matter which may be in the system. • Before slackening the main condensing breather pipe exchanger 20 in Fig. 7.3 con- nect a small draining pipe to the hose nozzle INHIBITION (Primary Heating Circuit) to drain water out. On the final refilling of the heating system it is important to ensure the system water is treated with a suitable scale and corrosion in- hibitor in accordance with the manufacturers...

  • Page 55: Condensate Pipe And Traps

    32 point in Fig. 7.9 and compare the value with that reported on the Gas supply pressure table (minimum inlet pressure) in the "Technical Data" section (pag. 28 Inovia 25S ERP. • Ensure the test nipple 32 in Fig. 7.9 is firmly Fig. 7.7 closed.

  • Page 56: Lighting The Boiler

    CO/CO (The Fig. 7.11 limits for the boiler is given in "Technical Data" section pag. 28 Inovia 25S ERP: The LCD display displays the boiler tempera- contents / other flue gas figures) and ture (primary circuit) and the...

  • Page 57: Checking The Ignition Device

    74 of this manual. nance procedures for the gas supply, it may Reference figures are given in the "Technical Data" section (pag. 28 Inovia 25S ERP) of be necessary to repeat the resetting operation several times so as to remove the air present this manual (Flue gas figures).

  • Page 58: Instructing The User

    COMMISSIONING Verify the cleanness and correct filling of the condensate traps. 7.12 Instructing the user Hand over this combined User & Installation manual and the Service manual to the end user and explain how to use the unit. Take the User step by step through the lighting instructions.

  • Page 59: Advanced Commissioning

    ADVANCED COMMISSIONING ADVANCED COMMISSIONING Enabling functioning of the external temperature probe by the remote control Functioning with the external probe in the boiler must be enabled if the remote control (optional) is used. Act on the programming of the REMOTE con- trol to enable its functioning if the remote con- trol (optional) is used.
  • Page 60 ADVANCED COMMISSIONING Sequence for setting the K coefficient C.H. flow temperature °C • Enter in "programming mode" by sequen- K=4 K=3 K=1,5 tially pressing and holding keys 13 - 16 - 17 (Fig. 8.7) for 10 seconds at the same time until the letters P01 are displayed on the LCD display, indicating that "parameter 01, has been activated (Fig.

  • Page 61: Setting The Pump Post-Circulation

    ADVANCED COMMISSIONING setting made with keys 16 and 17 for a K 1,5 play (Fig. 8.10). is shown in Fig. 8.11. Sequence for setting the K coefficient with the remote control connected Act on the programming of the REMOTE con- trol to select the setting of the K coefficient.
  • Page 62 ADVANCED COMMISSIONING of each heat request. 17=42 seconds. • The writing P11 - SEt alternates on the dis- This time can be changed by a minimum of zero to a maximum of four minutes. play (Fig. 8.17). • Enter in "programming mode" by sequential- ly pressing keys 13 - 16 - 17 (Fig.

  • Page 63: Selecting The Reignition Frequency

    ADVANCED COMMISSIONING Selecting the reignition fre- quency When the boiler functions in normal on/off heating mode, the minimum time between two ignitions is set at three minutes (re-ignition fre- quency). This time can be changed by a minimum of zero to a maximum of eight and a half min- utes.
  • Page 64 ADVANCED COMMISSIONING • It is possible to modify parameter 10 by • Press buttons at the same 00=0s to 100=510s using keys 10 or 11 time to enter transparent programming (Fig. (each increase or reduction by a unit on 8.27). the display corresponds to 5 seconds).

  • Page 65: Boiler Adjustment Record

    P01 are displayed on the LCD P 08 reset display and the value of the parameter (41=Inovia 25S ERP), indicating that ”pa- Flue sweep function P 09 rameter 01” (Fig. 8.32) has been activated. C.H. reignition...
  • Page 66 ADVANCED COMMISSIONING 13 14 Fig. 8.31 Fig. 8.32 • Scroll the various parameters using keys 16 or 17 until the letters P02 are displayed on the LCD display, indicating that ”parameter 02” has been activated. • Press keys 10 or 11 to change the value and confirm the value of the parameter with key •...

  • Page 67: Gas Conversion

    • Carry out gas conversion by correctly re- placing the gas restrictor (Fig. 9.2), refer- Warnings ring to the "Technical Data" section pag. 28 (Inovia 25S ERP). The commissioning of this boiler and system must only be undertaken by a Gas restrictor...
  • Page 68 GAS CONVERSION • Exiting the “programming mode” is au- tomatic, after 15 minutes, or by cutting power. • Calibrate the gas valve according to the instructions given in the Service manual, section Gas valve - Adjustment. • Reposition the controls panel and re- mount the front panel of the body.

  • Page 69: Maintenance

    MAINTENANCE MAINTENANCE 10.1 Warnings The procedures detailed in this chapter must be carried out only by a Gas Safe Regis- tered Engineer. Thus you are advised to con- tact an Authorised Service Agent. For Ireland (IE), the servicing work must be carried out by a competent RGII registered.

  • Page 70: Dismantling The External Panels

    MAINTENANCE ings (Fig. 10.6). Side panels Loosen screws "B - F" and "C - H" in Fig. 10.6 and remove the two side panels "E" and "G" by pulling towards the outside. Fig. 10.4 • By pressing key 13 (Fig. 10.1) confirmation of the inserted value is obtained.

  • Page 71: Reassembly The External Panels

    MAINTENANCE Fig. 10.7 10.4 Reassembly the external panels Fig. 10.8 Side panels Fit the external panels "E" and "G" in the re- 10.5 Emptying the C.H. system verse order to that described on section "Dis- • Close the C.H. isolating valves (3 and 5 in mantling the external panels"...

  • Page 72: Cleaning The Condensing Primary Exchanger

    MAINTENANCE CLOSED Main circuit drain valve OPEN Fig. 10.12 10.6 Cleaning the condensing prima- ry exchanger and the burner Removing the fan burner unit 39 in Fig. 10.13. Fig. 10.10 • To make draining easier, unscrew the plug 29 of the automatic relief valve in Fig. 10.11. Fig.
  • Page 73 MAINTENANCE • Unhook the silencer pipe. Fig. 10.14 and the Air-gas duct gasket (Fig. • Insert a flat screwdriver in the connector re- 10.15) must be fully inspected and replaced at cess M and lever towards the bottom, dis- the discretion of the service engineer. connect the connector at the same time O by pulling towards the front O (Fig.

  • Page 74: Check The Pressure Of The Heating Expansion Vessel

    1 bar. following. If the pressure is less, see to correct pressuri- sation. Model Inovia 25S ERP Nominal heat input 25,0 (A) (E) 10.8 Checking the flue system Nominal efficiency...

  • Page 75: Checking The Condensate Drain Pipe

    MAINTENANCE 10.10 Checking the condensate drain 10.12 Checking the gas supply pres- pipe sure The condensate drain pipe 35 (Fig. 10.19) Check appliance for gas tightness. does not require any particular maintenance Re-check operational pressures as described but just check: in section "Checking the gas supply pressure"...
  • Page 76 MAINTENANCE Fig. 10.21 Flue sweep function at minimum output in domestic hot water mode • Press keys 16 and 17 (Fig. 10.20) at the same time until the LCD display displays the letters LP that alternate with the heating Fig. 10.23 water temperature value (e.g.45), indicating the activation of the "flue sweep function"...
  • Page 77 MAINTENANCE Fig. 10.25 • Press keys 13 - 16 - 17 (Fig. 10.20) at the same time again to exit the "flue sweep mode" and return to the previously set boiler status (Fig. 10.26). Winter Summer Fig. 10.26 Note to service engineers It is required that the burner seal lip seal and mixing chamber seal along with the flame detection electrode are inspected...

  • Page 78: Benchmark Commissioning And Servicing Section

    BENCHMARK COMMISSIONING AND SERVICING SECTION It is a requirement that the boiler is installed and commissioned to the manufacturers instruc- tions and the data fields on the commissioning checklist completed in full. To instigate the boiler guarantee the boiler needs to be registered with the manufacturer within one month of the installation.

  • Page 79: Gas Boiler System Commissioning Checklist

    GAS BOILER SYSTEM COMMISSIONING CHECKLIST This Commissioning Checklist is to be completed in full by the competent person who commissioned the boiler as a means of demonstrating compliance with the appropriate Building Regulations and then handed to the customer to keep for future reference. Failuretoinstallandcommissionaccordingtothemanufacturer’sinstructionsandcompletethisBenchmarkCommissioningChecklistwillinvalidatethe warranty.Thisdoesnotaffectthecustomer’sstatutoryrights.

  • Page 80: Service Record

    SERVICE RECORD It is recommended that your heating system is serviced regularly and that the appropriate Service Interval Record is completed. Service Provider BeforecompletingtheappropriateServiceRecordbelow,pleaseensureyouhavecarriedouttheserviceasdescribedinthemanufacturer’sinstructions. Alwaysusethemanufacturer’sspecifiedsparepartwhenreplacingcontrols. SERVICE 01 SERVICE 02 Date: Date: Engineername: Engineername: Companyname: Companyname: TelephoneNo: TelephoneNo: GassaferegisterNo: GassaferegisterNo: Atmax.rate: COppm AND CO ²...
  • Page 81 NOTES - 81 -...
  • Page 82 NOTES - 82 -...
  • Page 84 *1796221983* 17962.2198.3 0318 84A5 Biasi UK Ltd Commercial Road Leamore Enterprise Park WALSALL WS2 7NQ Sales Tel. 01922 714600 Tech. Service Tel. 01922 714636 www.biasi.co.uk...

This manual is also suitable for:

41-583-30

Table of Contents