Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Arrow Storage Products Manuals
  4. Outdoor Storage
  5. DKGA-A
  6. Owner's manual and assembly manual

Arrow Storage Products DKGA-A Owner's Manual And Assembly Manual

Commander series, mountaineer series
Hide thumbs

Advertisement

Quick Links

Download this manual
720041014
Owner's Manual
& Assembly Guide
Gloves must be worn
at all times to reduce
risk of injury!
* See Inside for Detailed Safety Information.
(Door Kit)
NOTE: These instructions are to be used to add a rear door to an existing Arrow Commander™
or Mountaineer™ Shed. If you are assembling a Commander™ or Mountaineer™ Shed as well
a Door Kit, use the manual included in the main carton (C1GA-A).
Two to three people are required for assembly.
Follow all safety precautions in the Commander™/Mountaineer™ Series Assembly Manual.
Note: It may be helpful to refer to the primary Commander™/Mountaineer™ Series Assembly Manual you used when you fi rst assembled your building.
If you have misplaced your original Commander™/Mountaineer™ Series Assembly Manual, it is available online at www.arrowsheds.com or you may
request an additional copy from customer service: 1-800-851-1085.
COMMANDER
MOUNTAINEER
www.arrowsheds.com
SERIES
™
SERIES
™
Model No.
01AR
DKGA-A

Advertisement

loading

Related Manuals for Arrow Storage Products DKGA-A

Summary of Contents for Arrow Storage Products DKGA-A

  • Page 1 * See Inside for Detailed Safety Information. Model No. DKGA-A (Door Kit) NOTE: These instructions are to be used to add a rear door to an existing Arrow Commander™ or Mountaineer™ Shed. If you are assembling a Commander™ or Mountaineer™ Shed as well a Door Kit, use the manual included in the main carton (C1GA-A).
  • Page 2 BEFORE YOU BEGIN... Safety precautions MUST be followed at all times throughout the construction of your building! •Care must be taken when handling various pieces of your building since many contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your building.
  • Page 3 HARDWARE LIST... 03AR Hardware Views by Key No. Key Part Part Qty. Description List 65103 Hex Nut (#8-32) #2 Phillips 65106 Square Nut (#10-32) 11/32 Hex. #10-32 65923 Small Bolt (#8-32 x 3/8) (10 mm) 65943 Large Bolt (#10-32 x 7/16) (11 mm) 65004 Small Screw (#8AB x 5/16) (8 mm) 66611...

  • Page 4: Table Of Contents

    PARTS LIST... 04AR Part Part Qty. Selected End Views by Key No. Description List 10618 Front Wall Panel 10622 Right Door Jamb 80037 Left Door Jamb Painted Painted Unpainted 10627 Front Wall Channel 10628 Front Wall Diagonal 10878 Long Fascia 10879 Short Fascia Unpainted...
  • Page 5 ASSEMBLY BY KEY NO. 05AR Door Kit Right Door Left Door...
  • Page 6 06AG Step Disassemble Rear Wall Remove Parts: IMPORTANT: Take care in • Roof Trim Cap (2) • Roof Panel (2) removing parts from building. • Roof Trim (2) • End Roof Panel (2) • Peak Cap (1) • Ridge Cap (1) They will be reused later.
  • Page 7 Step 1: Continued 07AG Remove Parts: You will need for this page: Install Edge Trim to cover • Roof Beam Brace (1) Gable Edge BEFORE doing 69835 • Roof Beam (4) ANY work with Gables. • Gable (2) Failure to do so could result •...
  • Page 8 Step 1: Continued 08AG Remove Parts: IMPORTANT: Take care in • Wall Panel (2) removing parts from building. • Side Wall Channel (2) They will be reused later. Remove last Wall Panel from both sides of the building. Remove top, middle, and bottom Screws on Adjacent Wall Panel as shown.
  • Page 9 Step 1: Continued 09AG Remove Parts: IMPORTANT: Take care in removing parts from building. • Corner Panel (2) They will be reused later. Remove Anchor Bolts from rear wall. Remove rear wall from building. Remove rear Corner Panels. IMPORTANT: TWO (2) PEOPLE SHOULD BE SUPPORTING THE REAR WALL AS IT IS UNFASTENED!
  • Page 10 Step 2: 10AR New Rear Wall Assembly You will need for this page: 10640 10652 10627 10628 10880 Wall Post Front Wall Front Wall Wall Post Front Frame (Hinge) (QTY: 38) Diagonal (QTY: 24) Channel 10878 10879 Left Front Wall Assembly Right Front Wall Assembly Long Fascia Short Fascia...

  • Page 11: Front Wall Panel

    Step 2: Continued 11AR You will need for this page: Assemblies from previous page: 10618 • Left Front Wall Assembly • Right Front Wall Assembly • Door Header Assembly Front Wall Reused Parts: (QTY: 12) (QTY: 8) Panel • Corner Panel (2) Slide the Door Header Assembly down onto the Front Wall Assemblies as shown and secure with Small Bolts and Nuts.

  • Page 12: Right Door Jamb

    Step 3: 12AG New Rear Wall Install You will need for this page: Assemblies from Step 2: 10622 80037 • New Rear Wall Assembly Reused Parts: Right Door Left Door • Side Wall Channel (2) (QTY: 2) (QTY: 6) Jamb Jamb (QTY: 6) Side Wall Channel will attach...
  • Page 13 Step 4: Wall Panels 13AG FASTEN TO TOP FRAMES Whenever a crimped rib and an uncrimped rib meet, the crimped rib should be placed UNDER the uncrimped rib if possible. Crimped Rib FASTEN TO WALL CHANNELS Uncrimped Rib Use the diagram to the right when attaching Wall Panels. •...
  • Page 14 Step 4: Continued 14AG You will need for this page: Reused Parts: Use washers on all fasteners • Wall Panel (2) used on painted parts. (QTY: 40) (QTY: 2) Working one side at a time, lift the Wall Panel into place and secure the Wall Panel with one (1) Bolt and Nut through the center hole at the overlap (see below).
  • Page 15 Step 5: Gables 15AR You will need for this page: Reused Parts: • Left Gable (1) • Right Gable (1) • Gable Brace (1) (QTY: 16) (QTY: 2) • Track Support (2) Gable must fi t UNDER Side Wall Angle at corner. Working with one Gable at a time, attach the Gables to the top Rear Frame with Large Screws.
  • Page 16 Step 5: Continued 16AG You will need for this page: 67293 Reused Parts: Roof Beams • Roof Beam (4) Weather (QTY: 12) Stripping Top View of Gables Tape should wrap around Seal the gap between the Gables using the gap between Gables. Weather Stripping Tape as shown.
  • Page 17 Step 5: Continued 17AG You will need for this page: Reused Parts: • Roof Beam Brace (1) (QTY: 2) Roof Beam Brace Attach the Roof Beam Brace to the Tab end attaches to Roof Beam. Track Support with one (1) Small Bolt and Nut as shown.
  • Page 18 Roof Install Prep Page 18AG Read through all of Roof Assembly before beginning Step 6. IMPORTANT: At this time, take a moment to ensure the building is level and square. Measure the building diagonally again to make sure the building is square.
  • Page 19 Step 6: End Panels 19AG You will need for this page: Reused Parts: • Right Roof End Panel (1) • Left Roof End Panel (1) (QTY: 6) (QTY: 12) Secure the End Panel to the Main Roof Beam by placing a Small Screw in hole An Awl may be used to help align holes that are only slightly #1 (from the diagram below).
  • Page 20 Step 7: Roof Assembly 20AG You will need for this page: Reused Parts: • Roof Panel (2) • Ridge Cap (1) (QTY: 24) (QTY: 8) Attach the end of the rear Ridge Cap with two (2) • Starting with rib #5 below, every rib that is over holes in existing Ridge Cap with two (2) Small a Truss should be secured with a Small Bolt and Bolts and Nuts.
  • Page 21 Step 8: Roof Trim 21AG You will need for this page: Reused Parts: • Roof Trim (2) • Peak Cap (1) • Roof Trim Cap (2) (QTY: 2) (QTY: 4) (QTY: 6) IMPORTANT: Once the building is assembled, anchor the added sections of the building in the same manner as the rest of the building.
  • Page 22 Step 9: Door Assembly 22AG You will need for this page: 10623 10624 80051 Door Panel Right Door Left Door (QTY: 10) (Hinge) Panel Panel Refer to page 5 for Door assembly overview. Position Door Panels as shown and secure using Small Bolts and Nuts. The best way to assemble the Doors NOTE: Door Panels in the image is on a fl...

  • Page 23: Door Panel (Hinge)

    Step 9: Continued 23AG You will need for this page: 10635 10637 10678 [ NO HARDWARE NEEDED 10635 FOR THIS STEP ] Vert. Door Vert. Door Horiz. Door Brace (Hinge) Brace (Latch) Brace Extra hole along Position Horizontal Door Braces, INSIDE of Door.

  • Page 24: Horizontal Door Brace

    Step 9: Continued 24AG You will need for this page: 10636 Vert. Door (QTY: 12) Open ends of Vertical Door Braces Brace must face edge of Doors. Slide Vertical Door Braces into position with ends inside Horizontal Door Braces. Double check that the open ends of the Vertical Door Braces face the edges of the Door (see image to right) and secure with Large Screws in each Door.
  • Page 25 Step 9: Continued 25AG You will need for this page: Plastic Washer 10651 66781 10626 Diagonal (QTY: 13) (QTY: 2) Latch Plate Spring Latch (QTY: 2) Brace (QTY: 3) Position parts as shown and secure to upper inside corner of left Door with Large Screws.

  • Page 26: Cane Bolt Bracket

    Step 9: Continued 26AG You will need for this page: The Cane Bolt, Door Handles 10675 66780 and Slide Bolt are pre-packaged with thier own hardware. This hardware is not used when assembling Cane Bolt the building. Instead, use the (QTY: 26) Cane Bolt Bracket...
  • Page 27 Step 9: Continued 27AG You will need for this page: 66778 10648 10647 Astragal Top Trim Lock Eyelet (QTY: 20) (QTY: 20) (QTY: 2) Secure the Horizontal Door Brace to the Door with Large Screws. Position Door If holes do not align, insert Screw Trim and Astragals as shown and secure at an angle.
  • Page 28 Step 9: Continued 28AG You will need for this page: 66782 66779 10651 Door Handle Slide Bolt Latch Plate (QTY: 8) (QTY: 4) Slide Latch Plate into position on the Left Do not use hardware supplied Door. Next, position the Slide Bolt on the with Door Handle and Slide Bolt.
  • Page 29 Step 9: Continued 29AG Slide Bolt may need adjustment If Slide Bolt does not align properly, you may need to insert plastic washers between the to align properly. door and the Slide Bolt to ensure proper fi t. Adjust number of plastic washers until desired fi...
  • Page 30 ASSEMBLY NOTES...
  • Page 31 ASSEMBLY NOTES...