Konica Minolta AeroDR System Operation Manual page 24

1.3 Safety precautions
Article 12
As for type-approval qualified low-power radio-
frequency generator, no company, firm, or user
may arbitrarily change the frequency, increase
the power or alter the function or characteristics
of the original design without prior permission.
Article 14
The use of low-power radio-frequency electric
machines shall not affect air flight safety or
disturb lawful communication. If disturbance is
found, the use of such electric machines shall be
suspended immediately and such use shall not
be resumed until the disturbance is eliminated.
Lawful communication mentioned in the pre-
ceding paragraph refers to wireless communi-
cation operation in accordance with the provi-
sions of the Telecommunication Law.
Low-power radio-frequency electric machines
shall tolerate disturbance from lawful commu-
nication or from radio-wave radiation electric
machine for industrial, scientific or medical use.
China
1. Clearly indicate the technical indicators and
the scope of usage in the accompanying doc-
ument, and explain the usage of all controls,
adjustments, and switches, etc.
Operating frequency range: 5725-5850 MHz

Transmit power: ≤500 mW and ≤27 dBm

Equivalent isotropic radiated power (EIRP):

≤2 W and ≤33 dBm
Maximum radiation power density:

≤13 dBm/MHz and ≤19 dBm/MHz (EIRP)
Frequency Tolerance limit: 20 ppm

Transmit power at the band edge (EIRP):

≤80 dBm/Hz (≤5725 MHz or ≥5850 MHz)
Spurious emissions:

≤-36 dBm/100 kHz (30-1000 MHz)
≤-40 dBm/1 MHz (2400-2483.5 MHz)
≤-40 dBm/1 MHz (3400-3530 MHz)
≤-33 dBm/100 kHz (5725-5850 MHz)
(Note: Other than ±2.5-times supported channel bandwidth)
≤-30 dBm/1 MHz (Other 1-40 GHz)
2. Do not arbitrarily change frequency or in-
crease transmit power (including the added
radio frequency amplifier). In addition, do
not mount an antenna without permission, or
change to another transmission antenna.
3. When in use, do not cause harmful interference in
other legal wireless communication services. If you
find interference to be occurring, discontinue use
immediately. After taking measures to eliminate in-
terference, you may continue using the device.
4. If you use low power radio equipment, you must
accept interference from various wireless ser-
vices or radiation interference from industrial,
scientific and medical application equipment.
5. Do not use near a plane or an airport.
South Korea
Because this wireless equipment may be af-
fected by radio interference, it cannot provide
services related with life safety.
Thailand
AeroDR Detector conforms to NTC technical
requirement.
Brazil
This equipment operates secondarily, that is, it
doesn't benefit from protection against harm-
ful interference, even from stations of the same
type, and cannot cause interference to systems
that operate primarily.
AeroDR Detector has been approved by ANA-
TEL in compliance with the procedures regu-
lated by Resolution 242/2000 and complies
with the applicable technical requirements.
AeroDR system and Stitching system fulfill the
requirements set forth in INMETRO Ordinance
No 350, dated 06/09/2010, and other regula-
tions pertaining to compulsory certification
of Electrical Equipment Subject to Sanitary
Surveillance by ANVISA (RDC No 27, dated
21/06/2011, and Normative Instruction No 11,
dated 16/12/2014).
Konica Minolta hereby declares that the Aero
DR System and Stitching System products ful-
fill the biocompatibility aspects of ISO 10993-
1:2009.
This equipment operates with a voltage of AC
127V.
For more information, please visit:
http://www.anatel.gov.br
Mexico
This equipment operates on a secondary ba-
sis; consequently, you must accept harmful in-
terferences from equipment of the same type,
and cannot cause interferences to systems
operating on a primary basis.
24