Other Settings; Fax Setting - Oki MC573 Advanced Manual

• Other Settings

Item
Default Mode
Redial Tries
Redial Interval
Block Junk Fax Setting
Registered List Register / Edit
Delete
Ring Response
Dialing Pause Duration
Rx Reduc. Rate
Reduc. Margin
ECM Mode
PreFix
Received Time Stamp
Print Check Message
Duplex
Distant Station Priority
Factory Description
default
setting
Normal Sets the default screen of fax.
2 time(s) Sets the number of redial attempts.
Available range: 0 to 9 times
1 minute(s) Sets the time between redial attempts.
Available range: 0 to 5 minutes
OFF Sets Block Junk mode Fax.
(NULL) Register / Edit addresses for Block Junk Fax
when [Mode2] or [Mode3] is set.
Delete addresses for Block Junk Fax when
[Mode2] or [Mode3] is set.
1 Ring Sets the number of rings required before
receiving an incoming fax.
2 second(s) Sets the dial pause time.
Available range: 0 to 10 seconds
Auto Sets the reception reduction rate.
24 mm (0.9 Sets the threshold level of reception
inch) or reduction.
100 mm (3.9 Available range: 0 to 100 mm (0 to
inch) 3.9 inches)
ON Sets whether to use the error correction
mode.
(NULL) Sets the dialing prefix. You can enter up to 40
digits.
OFF Sets whether to print the time stamp on
received faxes.
ON Sets whether to report the error content if a
transmission error occurs.
OFF Sets simplex or duplex for printing received
fax and the binding position for duplex
printing.
Type 1 Sets the priority order of information for
Distant Station (information of the
destination).
Priority (High > Low)
[Type 1]: Destination information > Name in
speed dial > Phone number
[Type 2]: Name in speed dial > Phone
number

• Fax Setting

Item
Service Bit
Country Code
A/R Full Print
Daily Tx/Rx Log Report Setting
Print Time
Tone For Echo (For Transmission)
Tone For Echo (For Reception)
H/Modem Rate (For Tx)
H/Modem Rate (For Rx)
Attenuator
MF Attenuator
Pulse Make Ratio
Pulse Dial Type
MF(Tone) Duration
Calling Timer
PBX Line
- 327 -
9. Operating Management/ Specifications
Factory Description
default
setting
OFF If set to OFF, some menu items are not
displayed on the screen.
International or Sets the country code.
U.S.A
ON Sets whether to print the list of the
communication results automatically after
every 50 communications.
OFF Enables / disables to print a daily report.
0 Hour Sets the date and time for printing the daily
0 Minute report.
0 Second
Disable Displays only if Service Bit is ON.
Disable Displays only if Service Bit is ON.
33.6 Kbps Sets the default modem reception
transmission speed while the machine is
sending a fax.
33.6 Kbps Sets the default value of the modem
transmission speed while the machine is
receiving a fax.
10 dB, Range: Enter Attenuator. Displays only if Service Bit
0 - 15 dB is ON.
8 dB, Range: 0 Enter MF(Tone) Attenuator. Displays only if
- 15 dB Service Bit is ON.
40%, Range: Sets to make rate of DP (10 pps) during call.
33, 39, 40% Displays only if Service Bit is ON and Tone /
Pulse setting is PULSE.
N, Range: N, Sets the pulse type for dialing. Displays only
10-N, N+1 if Service Bit is ON and Tone / Pulse setting
is PULSE.
100 mseconds, Enter MF(Tone) Duration. Displays only if
Range: 75, 85, Service Bit is ON and Tone / Pulse setting is
100 mseconds TONE.
60 mseconds, Displays only if Service Bit is ON.
Range: 1 -
255 seconds
OFF When connecting to PBX (internal
exchange), put it to [ON].