Omron 3G3MX2 Quick Start Manual page 29

MX2 Quick Start Guide
Option Terminal
Code Symbol
40 TL Torque Limit Selection
41 TRQ1 Torque limit switch 1
42 TRQ2 Torque limit switch 2
44 BOK Brake confirmation
46 LAC LAD cancellation
47 PCLR Pulse counter clear
50 ADD ADD frequency enable
51 F-TM Force Terminal Mode
52 ATR Enable torque command input
53 KHC Clear watt-hour data
56 MI1 General purpose input (1)
57 MI2 General purpose input (2)
58 MI3 General purpose input (3)
59 MI4 General purpose input (4)
60 MI5 General purpose input (5)
61 MI6 General purpose input (6)
62 MI7 General purpose input (7)
65 AHD Analog command hold
66 CP1 Multistage-position switch (1)
67 CP2 Multistage-position switch (2)
68 CP3 Multistage-position switch (3)
69 ORL Limit signal of homing
70 ORG Trigger signal of homing
73 SPD Speed/position changeover
77 GS1 * GS1 input
78 GS2 * GS2 input
81 485 Start EzCOM
82 PRG Executing Drive programming
83 HLD Retain output frequency
84 ROK Permission of Run command
85 EB Rotation direction detection
(C007 only)
86 DISP Display limitation
255 no No function
All this functions could be assigned to any of the multi-function inputs on parameters C001 to C007, select if the input will be
normally open or normally close and the response time of the input.
26
Input Function Summary Table
Function Name
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
Parameter Parameter name
C001 Input [1] function
C002 Input [2] function
C003 Input [3] function
[GS1 assignable]
C004 Input [4] function
[GS2 assignable]
C005 Input [5] function
[PTC assignable]
C006 Input [6] function
C007 Input [7] function
Description
Setting of b040 is enabled
Max. torque is limited with 200%
Torque limit related parameters of Powering/regen, and FW/RV modes are selected by the
combinations of these inputs.
Brake confirmation signal received
Brake confirmation signal not received
Set ramp times are ignored. Inverter output immediately follows the freq. command.
Accel. and/or decel. is according to the set ramp time
Clear the position deviation data
Maintain the position deviation data
Adds the A145 (add frequency) value to the output frequency
Does not add the A145 value to the output frequency
Force inverter to use input terminals for output frequency and Run command sources
Source of output frequency set by A001 and source of Run command set by A002 is used
Torque control command input is enabled
Torque control command input is disabled
Clear watt-hour data
General purpose input (1) to (7) under Drive programming
Analog command is held
Analog command is not held
Multistage position commands are set according to the combination of these switches.
Limit signal of homing is ON
Starts homing operation
Speed control mode
Position control mode
EN60204-1 related signals: Signal input of "Safe torque off" function.
Starts EzCOM
No execution
Executing Drive program
No execution
Retain the current output frequency
Run command permitted
Forward rotation
Reverse rotation
Only a parameter configured in b038 is shown
All the monitors can be shown
(input ignored)
Description
Select input terminal [1] function
Select input terminal [2] function
Select input terminal [3] function
Select input terminal [4] function
Select input terminal [5] function
Select input terminal [6] function
Select input terminal [7] function
MX2 Quick Start Guide