H5: Memobus/Modbus Serial Communication - YASKAWA Z1000 User Manual

B.7 H Parameters: Multi-Function Terminals
No.
(Addr. Name
Hex)
Multi-Function Analog
H4-07
Output Terminal FM
(423)
Signal Level Selection
Multi-Function Analog
H4-08
Output Terminal AM
(424)
Signal Level Selection
u

H5: MEMOBUS/Modbus Serial Communication

No.
(Addr. Name
Hex)
H5-01
(425)
Drive Slave Address
<1>
H5-02 Communication Speed
(426) Selection
H5-03 Communication Parity
(427) Selection
Stopping Method after
H5-04
Communication Error
(428)
(CE)
H5-05 Communication Fault
(429) Detection Selection
H5-06 Drive Transmit Wait
(42A) Time
H5-07
RTS Control Selection
(42B)
H5-08 Communication
(62D) Protocol Selection
H5-09
CE Detection Time
(435)
Unit Selection for
H5-10
MEMOBUS/Modbus
(436)
Register 0025H
Communications
H5-11
ENTER Function
(43C)
Selection
H5-12 Run Command Method
(43D) Selection
310
LCD Display
Level Select1 0: 0 to 10 V
0: 0-10 VDC 2: 4 to 20 mA
2: 4-20 mA
AO Level Select2 0: 0 to 10 V
0: 0-10 VDC 2: 4 to 20 mA
2: 4-20 mA
LCD Display
Selects drive station slave number (address) for MEMOBUS/
Modbus terminals R+, R-, S+, S-. Cycle power for the setting
Serial Comm Adr
to take effect.
Serial Baud Rate 0: 1200 bps
0: 1200 bps 1: 2400 bps
1: 2400 bps 2: 4800 bps
2: 4800 bps 3: 9600 bps
3: 9600 bps 4: 19200 bps
4: 19.2 kbps 5: 38400 bps
5: 38.4 kbps 6: 57600 bps
6: 57.6 kbps 7: 76800 bps
7: 76.8 kbps 8: 115200 bps
8: 115.2 kbps Cycle power for the setting to take effect.
Serial Com Sel 0: No parity
0: No parity 1: Even parity
1: Even parity 2: Odd parity
2: Odd parity Cycle power for the setting to take effect.
Serial Fault Sel 0: Ramp to stop
0: Ramp to Stop 1: Coast to stop
1: Coast to Stop 2: Fast Stop
2: Fast-Stop 3: Alarm only
3: Alarm Only 4: Run at d1-04
4: Alarm(d1-04)
0: Disabled
Serial Flt Dtct
1: Enabled
0: Disabled
If communication is lost for more than two seconds, a CE fault
1: Enabled
will occur.
Set the wait time between receiving and sending data.
Transmit WaitTIM
RTS Control Sel 0: Disabled. RTS is always on.
0: Disabled 1: Enabled. RTS turns on only when sending.
1: Enabled
Protocol Select Selects the communication protocol.
0: MEMOBUS 0: MEMOBUS/Modbus
1: N2 1: N2 (Metasys)
2: P1 2: P1 (APOGEE FLN)
3: BACnet 3: BACnet
Sets the time required to detect a communications error.
CE Detect Time Adjustment may be needed when networking several drives.
CommReg 25h Unit 0: 0.1 V units
0: 0.1 V 1: 1 V units
1: 1 V
0: Drive requires an Enter command before accepting any
Enter CommandSel
changes to parameter settings.
0: Enter Required
1: Parameter changes are activated immediately without the
1: No EnterRequired
Enter command (same as V7).
Run CommandSel 0: FWD/Stop, REV/Stop
0: FWD Run &REV 1: Run/Stop, FWD/REV
Run
1: Run & FWD/REV
Description
Description
YASKAWA ELECTRIC TOEP C710616 45F YASKAWA AC Drive – Z1000 User Manual
Values Page
Default: 0
–
Range: 0, 2
Default: 0
–
Range: 0, 2
Values Page
Default: 1F (Hex)
Min.: 0 178
Max.: FF
Default: 3
178
Range: 0 to 8
Default: 0
179
Range: 0 to 2
Default: 3
179
Range: 0 to 4
Default: 1
179
Range: 0, 1
Default: 5 ms
Min.: 5 179
Max.: 65
Default: 1
180
Range: 0, 1
Default: 0
180
Range: 0 to 3
Default: 2.0 s
Min.: 0.0 180
Max.: 10.0
Default: 0
180
Range: 0, 1
Default: 0
180
Range: 0, 1
Default: 0
181
Range: 0, 1