Windscreen, Rear Window - Skoda 105 s 1980 Workshop Manual

!
Door Cotch Retoiner
The position of the door cotch retoiner on
the door pillor ond/or the reor wing foce con
be odiusted within certoin limits ofter loosen-
ing its fostening screws. Adiust the retoiner
in the required position, check the door for cor-
rect closing ond fitting with the other ports of
the bodywork, ond then retighten the screws.
The door cotch must slide on to the leodlng
surfoce of the retoiner so thot it rests ogoinst
it.
Sometimes, it moy be necessory to ploce
o pocking piece under the retoiner (to prevent
t h e f o u l i n g o f t h e d o o r c o t c h p i n ) . l n s u c h
o cose, mork the position of the cotch on the
bodywork, slocken the screws, ond instoll o
p o c k i n g p i e c e u n d e r t h e r e t o i n e r s l i p p i n g i t
over the lower screws ond tipping it into po-
sition on the upper screws.
It is importont to observe the correct ongle
of the inclinotion of the retoiner leoding sur-
foce, which hos to correspond with the incli.
notion of the beoring surfoce of the door cotch
(outer door lock). Therefore, fosten the bose
plote of the retoiner so thot its upright stiffener
is porollel with the edge of the moulded recess
for the retoiner on the door pillor ond the reor
w i n g .
The leoding surfoce of the retoiner is provided
with o friction plote. In the cose of domoge
(excessive weor, impoct of on incorrectly od-
iusted door, etc.), prise off the originol friction
p l o t e o n d f i t o n e w o n e . l f t h e f r i c t i o n p l o t e i s
l o c k i n g o r i f i t i s e x c e s s i v e l y w o r n , t h e d o o r i s
opt to rottle.
Fi1.14.514 - Door Cotch Retoiner
14.6 WINDSCREEN, REAR WINDOW,
S I D E W I N D O W S
To Remove Windscreen ond Reor Window
Rernove the connection of the spocing Insert
o n d l i f t o w o y t h e s p o c i n g i n s e r t o f t h e g l o z i n g
r u b b e r m o u l d i n g u s i n g o s u i t o b l e t o o l . N o w
press corefully ogoinst the gloss from inside
t h e c o r o n d s l i p t h e l i P o f t h e g l o z i n g r u b b e r
moulding step by step over the edge of the
windscreen or window frome olong its entire
circumference, ond finolly lift owoy the gloss
together with the glozing rubber moulding.
To Refit Windscreen ond Reor Window
F i r s t c l e o n t h o r o u g h l y t h e e d g e s o f t h e g l o s s
o n d o f t h e w i n d o w o p e n i n g ( f r o m e ) . S l i p t h e
g l o z i n g r u b b e r m o u l d i n g o v e r t h e e d g e s o f t h e
g l o s s .
lnsert o twine with o smooth surfoce or, pre'
ferobly, o rubber insuloted coble of 2.5 to 3 mm
in diometer into the inner groove of the glozing
r u b b e r m o u l d i n g .
F i g . M . 6 l 1 - F i t t i n g G l o z i n g R u b b e r M o u l d i n g
o n o G l o s s P o n e
Fig.14.612 - Inserting o Twine into the Groove
o f t h e G l o z i n g R u b b e r M o u l d i n g
2 0 6