Skoda 105 s 1980 Workshop Manual page 22

il
tli
GEARBOX. FINAL DRIVE
Connection
D i m e n s i o n s
Tightening
torque Nmt)
Nuts of cosing clomping bolts .
Nut of primory shoft
Plnlon nut .
Nut of pinion beoring coP
Nut of releose sleeve bol
Nut of front cover bolt
Nut of speedometer shoft clip bolt
Nut of speedometer drive beoring bolt
Nut of reverse-geor pin bolt
Bolt of reverse-geor pin
Bolt of shifter forks
Bolt of cop of lock-boll springs
Silentblock bolt
Bolt of differentiol cose
Bolt of crown geor
Droin ond inspection hole plugs
Switch or bolt of reversing lomps .
REAR AXLE
Connection
M 8
M 2 2 x 1 . 5
M 24x1.5
M 8
M 6
M 8
M 2 2 x 1 . 5
M 1 4 x 1
D i m e n s i o n s
4 0 - 5 0
1 4 - 1 7
6 - 8
1 9 - 2 5
7 - 9
7 - 9
1 7 - 2 0
7 - 9
1 4 - 1 7
7 - 9
3 0 - 4 0
2 2 - 2 5
3 5 - 4 5
2 0 - 3 0
7 0 - 8 0
M 6
M 6
M 8
M 8
M 6
M 6
M 1 0
M 8
M 1 0 x 1
3 0 - 3 5
7 - 9
Tightening
torque Nmr)
Rood wheels nuts .
Nut of oxle-shoft boll
Nut of oxle shoft .
ioin; boit
M 1 2 x 1 . 5
M 8
M 18x1.5
M 8
M 1 0
Dimension
6 0 - 7 0
2 0 - 2 5
17O *)
a
4 0 - 5 0
Bolt of broke bocking plote
Bolt of wheel cylinder
FRONT AXIE
Connection
Tightening
torque Nml)
Nut fostening lower wishbone fulcrum brocket to bodywork
Nut of lower wishbone fulcrum brocket
(next to rubber bush - inner)
Ditto - outer lock nut .
Nut of upper wishbone fulcrum brocket
(next to rubber bush - inner)
Ditto - outer lock nut .
Nut of upper wishbone pin (connection with steering
knuckle pivot)
Nut of lower wishbone pin (connection with steering
knuckle socket)
Nut of wheel hub beoring .
Nut of steering knuckle pivot .
Nut of lower wishbone brocket bolt .
Nut of bolt fostening shock obsorber to its onchor brocket
Nut fostening shock obsorber to bodywork
Wheel nuts
Bolt fostening front oxle to bodywork .
Bolt of onti-roll bor brocket
see Chopter 6.5, points 24 ond 25
see Chopter 6.5, point 21
M
, M
M
M
M
M
1 2 x 1 . 5
12x1.5
12x1.5
12x1.5
1 2 x 1 . 5
12x1.5
6 s - 7 0
4 5 - 6 0
7 0 - 9 0
4 5 - 6 0
7 0 - 9 0
7 0 * )
7 0 * l
4 0 - 5 0
5 0 - 5 5
1 2 - 1 4
6 0 - 7 0
4 0 - 4 5
1 2 - 1 6
M 1 2 x 1 . 5
M 1 0
M 1 2 x 1 . 5
M 1 0
M 1 2 x 1 . 5
M 1 0
M 7
*) Further tightening os required for olignlng holes for the cotter pin.
2 2