Skoda 105 s 1980 Workshop Manual page 109

Pock with greose the plostic dust cup ond
press it over the nut till it snops home in po-
sition on the lever.
Refitting Upper Wishbones
4. When refitting wishbones which hove
been olreody used in the cor ond which ore
rother doubtful (for exomple, o distortion is
suspected os o result of o crosh), inspect them
corefully ond stroighten them, if necessory.
5. Press rubber bushes into the eyes from the
outer side. To focilitote their sliding in, dip
them in petrol or soop woter (suds). Put the
bushes into the wishbone eyes with their lorger
diometer first ond push them so for thot they
protrude from the eye by the some length on
either side. Blow off the soop woter with com-
p r e s s e d o i r s o t h o t i t d o e s n o o s s i s t t h e s l i p p i n g
of the bush during the next operotion.
6. Slip the spocing tube on the MP 6-122 driIt,
dip the drift in petrol or soop woter, ond, forcing
it through the rubber bush, press the spocing
tube into the bush.
B e f o r e p r e s s i n g i t i n , t u r n t h e s p o c i n g t u b e s o
thot the ioint of the pockoged bush foces the
top side of the wishbone.
7 . T h r e o d t h e w i s h b o n e p i n t h r o u g h t h e e y e ,
s l i p o n i t t h e c u p w i t h i t s d i s h e d p o r t f o c i n g
the bush, two wishbone brockets with the lugs
pointing owoy from the wishbone, ond the other
F i g . 6 . 5 / 2 - P r e s s i n g S p o c i n g T u b e i n t o
Bush Using MP 6-122 Drift
cup with its dished port tbword the other rubber
bush, ond threod the pin through the other eye.
8. Push the brockets towords the eyes ond
slip two circlips on the norrowest port of the
p i n . T o s l i p t h e m o n , h o l d t h e m w i t h t h e i r u n -
connected ends on the pin ond press down. Use
o screwdriver to move one of the circlips into
the groove of the pin, ond push the pin with the
circlip in position into the brocket. Clomp the
other brocket with the wishbone eye in o vice
t o c o m p r e s s t h e r u b b e r b u s h , o n d s l i p o n t h e
other circlip.
9. lnsert the rubber deod stop into the wish'
bone.
F i g . 6 . 5 / 3 - I n s t o l l i n g C i r c l i p i n t o P i n G r o o v e
1 0 . R e i n s t o l l t h e t w o o s s e n r b l e d w i s h b o n e s
o n t h e o x l e b o d y . F i t o p l o i n w o s h e r u n d e r t h e
s p r i n g w o s h e r s o f t h e l u g b o l t s . I n s t o l l , f r o m
obove, one
'l
mm or one 3 mm open (horseshoe)
wosher or the previously removed woshers on
the horizontcrl bolts between the brocket ond
t h e o x l e b o d y l u g .
First tighten the horizontol ond then the ver-
ticol bolts.
F i t t h e c u p s o n t h e w i s h b o n e p i n o n d s c r e w
down both nuts.
Refitting Lower Wishbones
11. Inspect the wishbones os per porogroph 4.
lnsert rubber bushes in the eyes of the wish-
bone fnom its inner side. Threod the wishbone
p i n t h r o u g h t h e e y e , s l i p o n i t t h e c u p o s w i t h
the upper wishbone, then two pin holders with
the recesses ot the inner hole focing eoch
other, onother cup, ond complete the operotion
by threoding the wishbone pin through the
other eye.
1 2 . S l i p c i r c l i p s o n t h e w i s h b o n e p i n o n d
lock with them the wishbone brockets in po-
sition. Proceed in the some monner os with the
upper wishbone (porogroph 8).
1 1 0
Rubber