Installing The 4285/4286 Vip Module; Figure 3-34: 4100Sm Using Home Automation - Honeywell VISTA-128BP Installation And Setup Manual

VISTA-128BP/VISTA-250BP Installation and Setup Guide
1 2 3 4 5 6 7 8
NU
To TB6 Aux. Power (+)
To TB7 Aux. Power (-)

Figure 3-34: 4100SM Using Home Automation

Installing the 4285/4286 VIP Module

The 4285/4286 VIP Module is an add-on accessory that
permits the user to access the security system (and
relays) via a TouchTone telephone. This may be done
either from the premises or by calling the premises
from a remote location. Only one VIP Module can be
used in a security system. This module must be
enabled as Device Address 4 in the Device
Programming in #93 Menu Mode, and must be
assigned to a partition.
The 4285/4286 VIP Module is not permitted in
U L
UL installations.
Detailed operating instructions for phone access
to the security system are provided with the VIP
Module.
The 4285/4286 VIP Module features:
•
Allows the user to receive synthesized voice
messages over the phone regarding the status of
the security system.
•
Allows the user to arm and disarm the security
system and perform most other commands using
the telephone keypad.
•
Allows the user to control relays using the
telephone keypad.
•
Provides voice annunciation over the phone to
confirm any command that is entered.
•
Announces many of the same words that would
normally be displayed on an alpha keypad under
the same system conditions. Refer to the words in
bold on the Alpha Vocabulary list found in the #93
Menu Mode in the Programming Guide.
•
Can be supervised for connection to control panel
(annunciated and reported as Zone 804).
3-28
WWW.DIYALARMFORUM.COM
9
J8 CONNECTOR
4142TR CABLE (SUPPLIED WITH 4100SM)
4100SM SERIAL MODULE
8
+ PWR
(25mA current draw)
7
- (GND)
6 RXD
5
not used
4
not used
To Terminal TB23
3 TXD
(Zone 9 [+])
2
not used
1
DTR
RED BLUE
To Serial Port
of Computer
WWW.DIYALARMFORUM.COM
NOTE: See the Home Automation software
instructions for details concerning its operation.
WHITE
4100SM-013-V0
The 4285/4286 is wired between the control panel and
the premises' handset(s) (see Figure 3-35). It listens
for TouchTones on the phone line and reports them to
the control panel. During on-premises phone access, it
powers the premises phones. During off-premises
phone access, it seizes the line from the premises
phones and any answering machines.
To install the VIP module, perform the following steps:
Step
1
2
3
• The VIP module will not operate until the
device address (04) is enabled in the control's
Device Programming in #93 Menu Mode .
• Do not mount the VIP Module on the cabinet
door or attempt to attach it to the PC board.
Action
Mount the module in the control cabinet if
space is available or, if this is not possible,
on the side of the cabinet or adjacent to it.
If you mount the VIP Module inside the
control cabinet, attach it to the cabinet's
interior surface with 2-faced adhesive tape.
You may leave the module's cover off if it is
mounted within the cabinet.
If you mount the module outside the
cabinet, use the screw holes at the rear to
mount horizontally or vertically (2-faced
adhesive tape may be used, if preferred).
Affix the 4285/4286 connections label
(supplied separately) to the inside of the VIP
Module's cover, if the cover is used.
Otherwise, affix the label to the inside of the
control cabinet's door.
Make 12V (+) and (–) and data-in and data-
out connections from the VIP Module to the
control, using the connector cable supplied
with the VIP Module. These are the same
connections as for remote keypads.