Installing The 4285/4286 Vip Module; Figure 3-26: 4100Sm Using A Serial Printer - Honeywell ADEMCO VISTA-40 Installation And Setup Manual

VISTA-40 Installation and Setup Guide
Connecting the 4100SM to a Serial Printer
To connect a serial printer using the 4100SM, refer to
Figure 3-26 and perform the following steps:
Action
Step
Connect terminal 1 on the 4100SM to the
1
Violet wire on the 4142TR cable.
Connect terminal 6 on the 4100SM to the
2
Brown wire on the 4142TR cable.
Connect the 4142TR cable to J8 on the
3
control.
Connect terminals 8 and 7 of the 4100SM to
4
terminals 6 and 7 (aux. power (+) and (-)),
respectively of the control.
Connect the UL EDP Listed serial printer to
5
the 4100SM Interface Module.
The 4100SM Module is supplied with a 10-
foot RS232 cable. A longer cable can be used
if the VISTA-40 is separated from the serial
printer by more than 10 feet, but the total
cable length should be less than 50 feet.

Installing the 4285/4286 VIP Module

The 4285/4286 VIP Module is an add-on accessory that
permits the user to access the security system (and
relays) via a TouchTone telephone. This may be done
either from the premises or by calling the premises from
a remote location. Only one VIP Module can be used in
a security system. This module must be enabled as
Device Address 4 in the Device Programming in #93
Menu Mode, and must be assigned to a partition.
The 4285/4286 VIP Module is not permitted in
U L
UL installations.
Detailed operating instructions for phone access
to the security system are provided with the VIP
Module.
The 4285/4286 is wired between the control panel and
the premises' handset(s) (see Figure 3-27). It listens for
TouchTones on the phone line and reports them to the
control panel. During on-premises phone access, it
powers the premises phones. During off-premises phone
access, it seizes the line from the premises phones and
any answering machines.
3-20
1 2 3 4 5 6 7 8
NU
To TB6 Aux. Power (+)
To TB7 Aux. Power (-)
4100SM JUMPERS
(CUT TO SET RESPECTIVE SIGNAL FLOATING)
COLOR FUNCTION PIN #
RED CD 8
BLUE CTS 5
WHITE DSR 6

Figure 3-26: 4100SM Using a Serial Printer

NOTE: See the 4100SM Installation Instructions for
details concerning the serial printer operation.
The 4285/4286 VIP Module features:
•
Allows the user to receive synthesized voice
messages over the phone regarding the status of
the security system.
•
Allows the user to arm and disarm the security
system and perform most other commands using
the telephone keypad.
•
Allows the user to control relays using the
telephone keypad.
•
Provides voice annunciation over the phone to
confirm any command that is entered.
•
Announces many of the same words that would
normally be displayed on an alpha keypad under
the same system conditions. Refer to the words in
bold on the Alpha Vocabulary list found in the #93
Menu Mode in the Programming Guide.
•
Can be supervised for connection to control panel
(annunciated and reported as Zone 804).
• The VIP module will not operate until the
device address (04) is enabled in the control's
Device Programming in #93 Menu Mode.
• Do not mount the VIP Module on the cabinet
door or attempt to attach it to the PC board.
9
J8 CONNECTOR
4142TR CABLE (SUPPLIED WITH 4100SM)
4100SM SERIAL MODULE
8 + PWR
(25mA current draw)
7 - (GND)
6 RXD
5
not used
4
not used
3
TXD
2
not used
1
DTR
RED BLUE
USE GENDER CHANGER 3M
Cable
SUPPLIED WITH 4100SM
Supplied with
IF PRINTER HAS DB25
4100SM
MALE CONNECTOR
SERIAL PRINTER
SET FOR: 8 DATA BITS
EVEN PARITY
STOP BIT
300/1200 BAUD
WHITE