Figure 3-20: 5881 Rf Receiver (Cover Removed) - Honeywell VISTA-128BP Installation And Setup Manual

MOUNTING
HOLES
Installing the 5800TM Module
Installation of this module is necessary only if you are
using a 5827BD or 5804BD Bi-directional device.
The address for the 5800TM must be enabled
in the control's Device Programming in the #93
Menu Mode as a keypad and then assigned to
a partition.
To install the 5800TM, perform the following steps:
Step Action
1 Mount the unit using its accompanying
mounting bracket near the RF receiver.
The 5800TM must not be installed
within the control cabinet. It must be
between one and two feet from the
receiver's antennas.
2 Set the module for the appropriate address.
For Address Setting 28 cut the red jumper;
for Address 29 cut the white jumper; for
Address 30 cut both jumpers.
Make sure the address setting is not
being used by another device (keypad,
relay module, etc.).
3 Connect the module's wire harness to the
keypad terminals (6, 7, 8, and 9). Plug the
connector at the other end of the harness
into the module.
WWW.DIYALARMFORUM.COM
ANTENNAS
INSERT IN
CIRCUIT
RIGHT-HAND
BOARD
TERMINALS
DIP SWITCH INTERFERENCE
INDICATOR LED
DIP SWITCH #5 (PRESET ONLY ON 5881EH)
ON: SETS 5881EH FOR USE IN COMMERCIAL
FIRE APPLICATIONS (SEE THE RECEIVER'S
INSTRUCTIONS)*.
OFF: USE IN NON-COMMERCIAL FIRE
INSTALLATIONS.
* FOR COMMERCIAL FIRE APPLICATIONS
THE 5881EH PC BOARD MUST BE MOUNTED
IN A SEPARATE CABINET (SEE RECEIVER'S
INSTRUCTIONS FOR DETAILS).

Figure 3-20: 5881 RF Receiver (cover removed)

WWW.DIYALARMFORUM.COM
TO CONTROL'S REMOTE KEYPAD
CONNECTION POINTS.
USE MAX. of 220 ft. [67m of #22 (0.64mm)
WIRE or 550 ft. (168m) of #18 (1mm) WIRE
FOR EACH RUN. OBSERVE 20 ft. MAX.
FOR COMMERCIAL FIRE INSTALLATIONS.
(SEE RECEIVER'S INSTRUCTIONS.)
YELLOW
DIP SWITCH WHITE AREAS = SWITCH
RED
HANDLES. POSITION 2-4 DETERMINE
BLACK RECEIVER'S ADDRESS. CONSULT
CONTROL'S INSTRUCTIONS FOR
GREEN
ADDRESS TO USE. DIP SWITCH BELOW
SHOWN SET FOR ADDRESS "0."
WIRING
SWITCH
OPENING
POSITION
PLUG & SOCKET
House ID Sniffer Mode
This mode applies only if you are using a wireless
keypad (e.g., 5827) or bi-directional devices (e.g.,
5804BD). Use the House ID Sniffer mode to make sure
you do not choose a House ID that is in use in a nearby
system. The House ID must be programmed for the
receiver in Device Programming in the #93 Menu
Mode.
To enter House ID Sniffer mode, enter your Installer
Code + [#] + [2].
The receiver now "sniffs" for any House IDs in the area
and displays them. Keep the receiver in this mode for
2 hours. Use a House ID that is not displayed. Exit the
Sniffer mode by entering your Installer Code + OFF.
As Sniffer mode effectively disables RF point
reception, Sniffer mode cannot be entered
while any partition is armed.
5800 Series Transmitter Setup
5800 Series transmitters have the following
characteristics:
•
Transmitters have built-in serial numbers that
must be enrolled in the system using the #93
Menu Mode Programming, or input to the control
via the downloader.
•
Transmitters do not have DIP switches (except
5827, described separately).
•
Some transmitters, such as the 5816 and 5817,
can support more than one "zone" (referred to as
loops or inputs). Each loop must be assigned a
different zone number.
Section 3 - Installing the Control
RECEIVER ADDRESS SETTINGS
(" - " MEANS OFF)
0 1 2 3 4 5 6 7
5 PRESENT ONLY ON 5881EH (SEE TEXT AT LEFT)
ON ON ON ON
4
ON ON ON ON
3
ON ON ON ON
2
1
FOR FUTURE USE
3-15