Page 1: User Guide
Xenon™/Granit™ Xenon 1900, 1900h, 1910, 1902, 1902h, 1912, 1902g-BF Granit 1910i, 1911i, 1980i, 1981i Area-Imaging Scanners User Guide...
Page 2 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.
Page 3: Table Of Contents
Connect with RS485....................... 8 Mount a CCB01-010BT Charge Base ..................9 Mount a CCB02-100BT/CCB05-100BT Base ..............9 Reading Techniques........................11 Xenon 1900/1902/1910/1912 and Granit 1910i/1911i ........11 Granit 1980i/1981i......................11 Menu Bar Code Security Settings..................12 Set Custom Defaults ........................12 Reset the Custom Defaults......................
Page 4 Remote MasterMind™ for USB ....................20 ® Verifone Ruby Terminal......................20 ® Gilbarco Terminal ........................21 Honeywell Bioptic Aux Port .....................21 ® Datalogic™ Magellan Aux Port ....................21 NCR Bioptic Aux Port........................22 Wincor Nixdorf Terminal ......................22 Wincor Nixdorf Beetle™ Terminal ..................22 Wincor Nixdorf RS232 Mode A....................23 Keyboard Country Layout......................23...
Page 5 RS232 Timeout........................37 XON/XOFF ..........................38 ACK/NAK...........................38 Scanner to Bioptic Communication ..................38 Scanner-Bioptic Packet Mode..................39 Scanner-Bioptic ACK/NAK Mode..................39 Scanner-Bioptic ACK/NAK Timeout ................39 Chapter 3 - Cordless System Operation: Xenon 1902g/1912 and Granit 1911i/1981i..................41 How the Cordless Charge Base/Access Point Works.............41 Link the Scanner to a Charge Base..................41 Link the Scanner to an Access Point ..................42 Replace a Linked Scanner ......................43 Communication Between the Cordless System...
Page 6 Base Charge Modes........................51 Page ..............................51 Page Mode ..........................51 Page Pitch ..........................52 Error Indicators..........................52 Beeper Pitch - Base Error....................52 Number of Beeps - Base Error ..................53 Scanner Report..........................53 Scanner Address ..........................53 Base or Access Point Address ....................54 Scanner Modes..........................54 Charge Only Mode ........................54 Charge and Link Mode......................54 Linked Modes .........................55 Unlink the Scanner........................55...
Page 7 Application Work Groups ......................67 Application Work Group Selection..................67 Reset the Factory Defaults: All Application Work Groups ..........68 Reset the Custom Defaults: All Application Work Groups ...........69 Use the Scanner with Bluetooth Devices................69 Bluetooth Secure Simple Pairing (SSP)................69 Bluetooth HID Keyboard Connect...................70 Virtual Keyboard........................71 Bluetooth HID Keyboard Disconnect................71 Bluetooth Serial Port - PCs/Laptops................72...
Page 8 Beeper and LED Sequences and Meaning................83 Scanner .............................84 Low Power Alerts..........................84 Low Power Alert Range .......................85 Low Power Alert Flash Number ..................85 Low Power Alert Repeat ......................85 Low Power Alert Beep ......................86 Base..............................86 Base Communication and Scanning ................86 Base Charge Status ......................87 Base Power Communication Indicator.................87 Reset Scanner ..........................87 Base Charge Modes........................88...
Page 9 Out-of-Range Alarm ........................95 Alarm Sound Type .........................95 Scanner Power Time-Out Timer .....................96 Flexible Power Management ....................97 Batch Mode ............................98 Batch Mode Beep ........................99 Batch Mode Storage......................99 Batch Mode Quantity ......................100 Enter Quantities ........................100 Batch Mode Output Order ....................102 Total Records........................102 Delete Last Code.........................102 Clear All Codes........................103 Transmit Records to Host....................103...
Page 10 Beeper Volume – Good Read ..................113 Beeper Pitch – Good Read ....................113 Vibrate – Good Read......................113 Beeper Pitch – Error ......................114 Beeper Duration – Good Read..................115 LED – Good Read ....................... 115 Number of Beeps – Good Read..................115 Number of Beeps –...
Page 11 Activation Character......................128 End Character Activation After Good Read ..............128 Character Activation Timeout..................129 Character Deactivation......................129 Deactivation Character ....................129 Illumination Lights ........................130 Aimer Delay..........................130 User-Specified Aimer Delay....................131 Aimer Mode ..........................131 Centering............................131 Single Code Centering......................132 Custom Centering ......................132 Preferred Symbology .......................134 High Priority Symbology....................135 Low Priority Symbology ....................135 Preferred Symbology Time-out..................135 Preferred Symbology Default ..................136...
Page 12 Silent Mode with Long LED ................... 144 Very Low Beeper (Nighttime Mode)................144 Low Beeper (Daytime Mode) ..................145 Quiet Operations - LED and Volume Settings .............. 145 Linking LED Colors and Sound ..................145 Number of LED Flashes ....................146 LED Flash Rate........................
Page 13 Data Format Editor Commands ..................160 Send Commands ........................160 Move Commands........................165 Search Commands......................167 Miscellaneous Commands .....................169 Data Formatter...........................173 Data Format Non-Match Error Tone................174 Primary/Alternate Data Formats ..................175 Single Scan Data Format Change................175 Chapter 9 - Symbologies................177 All Symbologies..........................178 Message Length Description ....................178 Codabar............................179 Code 39 ............................181 Interleaved 2 of 5........................185...
Page 14 UPC-E0 ............................201 UPC-E0 Addenda Required.................... 201 UPC-E1 ............................203 EAN/JAN-13 ..........................204 EAN/JAN-13 Addenda Separator ................206 ISBN Translate........................206 EAN/JAN-8 ..........................207 MSI..............................209 GS1 DataBar Omnidirectional..................... 211 GS1 DataBar Limited ......................211 GS1 DataBar Expanded ......................212 Trioptic Code..........................
Page 15 Korea Post..........................231 ................................232 Chapter 10 - Imaging Commands.............233 Single-Use Basis ........................233 Command Syntax........................233 Image Snap - IMGSNP......................234 IMGSNP Modifiers ......................234 Image Ship - IMGSHP ......................237 IMGSHP Modifiers ......................238 Image Size Compatibility....................246 Intelligent Signature Capture - IMGBOX.................247 Signature Capture Optimize ..................247 IMGBOX Modifiers ......................248 RF Default Imaging Device ....................252 Chapter 11 - Utilities ...................253...
Page 16 Reset the Custom Defaults ....................263 Menu Commands ........................264 Chapter 13 - Product Specifications............295 Xenon 1900/1900h/1910 Corded Scanner Product Specifications ....295 Xenon 1902/1902h/1912 Cordless Scanner Product Specifications ....296 Xenon 1902g-BF Scanner Product Specifications ............. 298 Granit 1910i Industrial Corded Scanner Product Specifications......299 Granit 1911i Industrial Cordless Scanner Product Specifications.......
Page 17 CCB01-010BT/CCB01-010BT-BF Base ..............315 Granit 1910i/1911i/1980i/1981i Scanner.............316 CCB02-100BT/CCB05-100BT Base................317 Chapter 14 - Maintenance and Troubleshooting ........319 Repairs............................319 Maintenance ..........................319 Cleaning the Scanner .......................319 Cleaning the Window ......................319 Health Care Housing......................320 Inspecting Cords and Connectors ................320 Replacing Cables in Corded Scanners ................320 Replacing a Xenon Interface Cable................321 Replacing a Granit Interface Cable ................321 Replacing Cables and Batteries in Cordless Systems..........321...
Page 18 Programming Chart......................... 341 Xenon/Granit User Guide...
Page 19: Customer Support
To obtain warranty or non-warranty service, you must first obtain a Return Material Authorization number (RMA #) and then return your product to Honeywell (postage paid) with a copy of the dated purchase record. To learn more, go to www.honeywellaidc.com...
Page 20 xviii Xenon/Granit User Guide...
Page 21: Chapter 1 - Get Started
Honeywell bar code scanners are factory programmed for the most common ter- minal and communications settings. If you need to change these settings, pro- gramming is accomplished by scanning the bar codes in this guide.
Page 22 1. Connect the appropriate interface cable to the device first, then to the com- puter. Corded Xenon Scanner USB Connection: Corded Granit Scanner USB Connection: Xenon/Granit User Guide...
Page 23 2. If you are connecting a Granit scanner, make sure the cable is pushed tightly into the scanner. Loosen the locking plate and slide it over the base of the cable connector to lock the cable in place. Tighten the screw. CCB01-010BT/ CCB01-010BT-BF Base USB Connection:...
Page 24: Connect With Keyboard Wedge
For additional USB programming and technical information, refer to “USB Applica- tion Note,” available at www.honeywellaidc.com. Connect with Keyboard Wedge A scanner or cordless base can be connected between the keyboard and PC as a “keyboard wedge,” where the scanner provides data output that is similar to key- board entries.
Page 25 3. If you are connecting a Granit scanner, make sure the cable is pushed tightly into the scanner. Loosen the locking plate and slide it over the base of the cable connector to lock the cable in place. Tighten the screw. CCB01-010BT/CCB01-010BT-BF Base Keyboard Wedge Connection: CCB02-100BT/CCB05-100BT Base...
Page 26: Connect With Rs232 Serial Port
The unit defaults to an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard. A carriage return (CR) suffix is added to bar code data. Connect with RS232 Serial Port 1. Turn off power to the terminal/computer. 2.
Page 27 3. If you are connecting a Granit scanner, make sure the cable is pushed tightly into the scanner. Loosen the locking plate and slide it over the base of the cable connector to lock the cable in place. Tighten the screw. CCB01-010BT/CCB01-010BT-BF Base RS232 Serial Port Connection: CCB02-100BT/CCB05/100BT Base...
Page 28: Connect With Rs485
Connect with RS485 A Xenon scanner or cordless base can be connected for an IBM POS terminal inter- face. (This interface is not available in the Granit devices.) 1. Connect the appropriate interface cable to the device, then to the computer. Corded Xenon Scanner RS485 Connection: CCB01-010BT...
Page 29: Mount A Ccb01-010Bt Charge Base
Mount a CCB01-010BT Charge Base 2.36 in. 2.8 in. 59.84mm 72.1mm 3.35 in. 8x32 thread 85.09mm x .39 in. (10mm) deep Mount a CCB02-100BT/CCB05-100BT Base The CCB02-100BT or CCB05-100BT Base can be mounted on either a horizontal or vertical surface. The cables can be routed through either the top or the bottom of the base.
Page 30 When mounted on a vertical surface, a locking system is used to secure the scan- ner when it is in the stand. When mounted on a horizontal surface, the locking mechanism should be set to unlocked (pushed up). When mounted on a vertical surface, the locking mechanism should be set to locked (pushed down).
Page 31: Reading Techniques
Reading Techniques Xenon 1900/1902/1910/1912 and Granit 1910i/1911i The Xenon 1900/1902 scanners have a view finder that projects a bright red aim- ing beam that corresponds to the scanner’s horizontal field of view. The Xenon 1910/1912 and Granit 1910i/1911i scanners have an aiming pattern. The aiming beam or pattern should be centered over the bar code, but it can be positioned in any direction for a good read.
Page 32: Menu Bar Code Security Settings
15° to 18° to prevent unwanted reflection. Menu Bar Code Security Settings Honeywell scanners are programmed by scanning menu bar codes or by sending serial commands to the scanner. If you want to restrict the ability to scan menu codes, you can use the Menu Bar Code Security settings.
Page 33: Reset The Custom Defaults
Save code, that entire sequence will be saved to your custom defaults. When you have entered all the commands you want to save for your custom defaults, scan the Save Custom Defaults bar code. Set Custom Defaults Save Custom Defaults Note: When using a cordless system, the Custom Defaults settings apply to all workgroups.
Page 34 Xenon/Granit User Guide...
Page 35: Chapter 2 - Program The Interface
CHAPTER PROGRAM THE INTERFACE Introduction This chapter describes how to program your system for the desired interface. Program the Interface - Plug and Play Plug and Play bar codes provide instant scanner set up for commonly used inter- faces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect.
Page 36: Laptop Direct Connect
Laptop Direct Connect For most laptops, scanning the Laptop Direct Connect bar code allows operation of the scanner in parallel with the integral keyboard. The following Laptop Direct Connect bar code also programs a carriage return (CR) suffix and turns on Emu- late External Keyboard (page 31).
Page 37: Rs485 Packet Mode
IBM Port 17 Interface IBM Port 9B HHBCR-2 Interface Each bar code above also programs the following suffixes for each symbology: Symbolog Suffix Symbology Suffix EAN 8 Code 39 00 0A 0B EAN 13 Interleaved 2 of 5 00 0D 0B UPC A Code 128 * 00 0A 0B...
Page 38: Usb Ibm Surepos
RS485 Packet Length If you are using Packet mode, you can specify the size of the data “packet” that is sent to the host. Scan the Packet Length bar code, then the packet size (from 20 - 256) from the Programming Chart, beginning on page 341, then Save.
Page 39: Usb Hid
No extra configuration (e.g., baud rate) is necessary. Note: If you scan the USB Serial bar code either with an older Honeywell serial driver, or no driver installed, you may no longer be able to scan bar codes. If this happens, either uninstall the older driver versions and install the latest driver, or delete the specific device entry in Device Manager.
Page 40: Ack/Nak Mode
* CTS/RTS Emulation Off ACK/NAK Mode ACK/NAK Mode On * ACK/NAK Mode Off Remote MasterMind™ for USB When using a USB interface, you may wish to configure your scanner to communi- cate with Remote MasterMind Scanner Management Software (ReM). Scan the ReM On bar code to communicate with ReM.
Page 41: Gilbarco ® Terminal
Gilbarco Settings Honeywell Bioptic Aux Port Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit.
Page 42: Ncr Bioptic Aux Port
NCR Bioptic Aux Port Scan the following Plug and Play code to program the scanner for an NCR bioptic scanner auxiliary port configuration. The following prefixes are programmed for each symbology: Symbology Prefix Symbology Prefix UPC-A Interleaved 2 of 5 UPC-E Code 128 Code 32...
Page 43: Wincor Nixdorf Rs232 Mode A
Wincor Nixdorf Beetle Settings Wincor Nixdorf RS232 Mode A Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf RS232 Mode A terminal. This bar code sets the baud rate to 9600 bps and the data format to 8 data bits, odd parity, 1 stop bit.
Page 44 Keyboard Countries (Continued) Azeri (Cyrillic) Azeri (Latin) Belarus Belgium Bosnia Brazil Brazil (MS) Bulgaria (Cyrillic) Bulgaria (Latin) Canada (French legacy) Canada (French) Canada (Multilingual) Xenon/Granit User Guide...
Page 45 Keyboard Countries (Continued) Croatia Czech Czech (Programmers) Czech (QWERTY) Czech (QWERTZ) Denmark Dutch (Netherlands) Estonia Faroese Finland France Gaelic Xenon/Granit User Guide...
Page 46 Keyboard Countries (Continued) Germany Greek Greek (220 Latin) Greek (220) Greek (319 Latin) Greek (319) Greek (Latin) Greek (MS) Greek (Polytonic) Hebrew Hungarian (101 key) Hungary Xenon/Granit User Guide...
Page 47 Keyboard Countries (Continued) Iceland Irish Italian (142) Italy Japan ASCII Kazakh Kyrgyz (Cyrillic) Latin America Latvia Latvia (QWERTY) Lithuania Lithuania (IBM) Xenon/Granit User Guide...
Page 48 Keyboard Countries (Continued) Macedonia Malta Mongolian (Cyrillic) Norway Poland Polish (214) Polish (Programmers) Portugal Romania Russia Russian (MS) Russian (Typewriter) Xenon/Granit User Guide...
Page 49 Keyboard Countries (Continued) Serbia (Cyrillic) Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation Sweden Switzerland (French) Switzerland (German) Xenon/Granit User Guide...
Page 50: Keyboard Style
Keyboard Countries (Continued) Tatar Turkey F Turkey Q Ukrainian United Kingdom United States (Dvorak) United States (Dvorak left) United Stated (Dvorak United States (International) Uzbek (Cyrillic) Keyboard Style This programs keyboard styles, such as Caps Lock and Shift Lock. If you have used Keyboard Conversion settings, they will override any of the following Keyboard Style settings.
Page 51 Regular is used when you normally have the Caps Lock key off. * Regular Caps Lock is used when you normally have the Caps Lock key on. Caps Lock Shift Lock is used when you normally have the Shift Lock key on (not common to U.S.
Page 52: Keyboard Conversion
Keyboard Conversion Alphabetic keyboard characters can be forced to be all upper case or all lowercase. So if you have the following bar code: “abc569GK,” you can make the output “ABC569GK” by scanning Convert All Characters to Upper Case, or to “abc569gk” by scanning Convert All Characters to Lower Case.
Page 53: Keyboard Modifiers
Keyboard Modifiers This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo Mode. Control + X (Control + ASCII) Mode On: The scanner sends key combinations for ASCII control characters for values 00-1F. Windows is the preferred mode. All key- board country codes are supported.
Page 54: Rs232 Modifiers
Numeric Keypad Mode On * Numeric Keypad Mode Off Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters. Default = Off. Automatic Direct Connect Mode On * Automatic Direct Connect Mode Off RS232 Modifiers...
Page 55: Rs232 Word Length: Data Bits, Stop Bits, And Parity
4800 9600 19200 38400 57,600 * 115,200 RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctua- tion), select 7 data bits.
Page 56: Rs232 Receiver Time-Out
7 Data, 2 Stop, Parity Even 7 Data, 2 Stop Parity None 7 Data, 2 Stop, Parity Odd 8 Data, 1 Stop, Parity Even * 8 Data, 1 Stop, Parity None 8 Data, 1 Stop, Parity Odd 8 Data, 1 Stop, Parity Mark RS232 Receiver Time-Out The unit stays awake to receive data until the RS232 Receiver Time-Out expires.
Page 57: Rs232 Handshake
RS232 Handshake RS232 Handshaking allows control of data transmission from the scanner using software commands from the host device. When RTS/CTS is turned Off, no data flow control is used. Flow Control, No Timeout: The scanner asserts RTS when it has data to send, and will wait indefinitely for CTS to be asserted by the host.
Page 58: Xon/Xoff
* ACK/NAK Off Scanner to Bioptic Communication The following settings are used to set up communication between Honeywell scan- ners and bioptic scanners. Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with a bioptic scanner.
Page 59: Scanner-Bioptic Packet Mode
Scanner-Bioptic Packet Mode Packet Mode On must be scanned to set the scanner’s format so it is compatible with a bioptic scanner. Default = Packet Mode Off. * Packet Mode Off Packet Mode On Scanner-Bioptic ACK/NAK Mode Bioptic ACK/NAK On must be scanned so the scanner will wait for an ACK or NAK from a bioptic scanner after each packet is sent.
Page 60 Xenon/Granit User Guide...
Page 61: Chapter 3 - Cordless System Operation: Xenon 1902G/1912 And Granit 1911I/1981I
CHAPTER CORDLESS SYSTEM OPERATION: XENON 1902G/1912 AND GRANIT 1911I/1981I Note: This chapter does not apply to corded or Xenon 1902g-BF scanners. See Cordless System Operation: Xenon 1902g-BF beginning on page 79 for Xenon 1902g-BF scanning systems. How the Cordless Charge Base/Access Point Works A cordless charge base or an Access Point provide the link between the cordless scanner and the host system.
Page 62: Link The Scanner To An Access Point
If the scanner and base have previously been linked, you do not receive any feed- back. If this is the first time that the scanner and base are linked, both devices emit a short chirp when their radios link. At this point, that one scanner is linked to one base.
Page 63: Replace A Linked Scanner
Replace a Linked Scanner If you need to replace a broken or lost scanner that is linked to a base or an Access Point, scan the Override Locked Scanner bar code below with a new scanner and place that scanner in the base, or scan the Access Point linking bar code. The locked link will be overridden;...
Page 64: Program The Scanner And Base Or Access Point
Program the Scanner and Base or Access Point When using the scanner and charge base or Access Point together as a system, menu parameters and configuration settings are stored in the charge base or Access Point. Therefore, when programming any menu configuration settings, the scanner must be linked to the intended charge base or Access Point.
Page 65: Page Button
range and you scan a bar code, the scanner issues an error tone indicating no com- munication with the base or Access Point. A cordless charge base can also sound an alarm. Refer to Out-of-Range Alarm, page 56. Scanner Is Moved Back Into Range The scanner relinks if the scanner or the base or Access Point have been reset, or the scanner comes back into range.
Page 66: Page Button And Presentation Modes
Page Button and Presentation Modes When in Streaming Presentation Mode, the scanner’s aimer goes out after a short time, but the scan illumination remains on all the time to continuously search for bar codes (see Streaming Presentation™ Mode on page 124). When in Temporary Streaming Presentation Mode, pressing the page button on the base puts the scanner into Streaming Presentation Mode until the timeout occurs.
Page 67: About The Battery
60 Second Timeout About the Battery Warning: There is a danger of explosion if the batteries are incorrectly replaced. Replace the batteries with only the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the recycle program for batteries as directed by the governing agency for the country where the batteries are to be discarded.
Page 68: Safety Precautions For Lithium Batteries
• If you are not sure if the battery or charger is working properly, send it to Honeywell International Inc. or an authorized service center for inspection. Refer to Customer Support on page xvii for additional information. Caution: Use only Honeywell Li-ion battery packs, model number BAT- SCN01, rated 3.7 Vdc, 7.4Whr in this device.
Page 69: Scanner Led Sequences And Meaning
LED = error; green LED = success of any type. Scanners and the CCB01-010BT base have audible indicators as well: 1 razz or error tone = error; 2 beeps = menu change; 1 beep = all other successes. The table below lists the indication and cause of the LED indication, beeps, and vibrations for the scanner.
Page 70: Base Power Communication Indicator
Base Power Communication Indicator To display the power indicator on a base or an Access Point, scan the Base Power Communication Indicator On bar code. To turn off the power indicator, scan the Off bar code. Default = On. * Base Power Communication Indicator On Base Power Communication Indicator Off...
Page 71: Base Charge Modes
Base Charge Modes When the base has both an external power supply (plugged into the auxiliary power port) and a host interface cable, it will draw its power from the external power sup- ply. When the base does not have an external power supply, it draws its power from the interface cable.
Page 72: Page Pitch
the button is pressed. The red LED on the base or blue LED on the Access Point will remain lit to indicate that Page Mode is off. (This light will go out when the button is pressed, then back on when it’s released.) Default = Page Mode On. Note: If you are using a Xenon 1902h model, refer to Quiet Operations - LED and Volume Settings...
Page 73: Number Of Beeps - Base Error
* Razz (250 Hz) Medium (3250 Hz) High (4200 Hz) Number of Beeps - Base Error Note: This feature only applies to the CCB01-010BT base. The number of beeps and LED flashes emitted by the CCB01-010BT base for an error condition can be programmed from 1 - 9. For example, if you program this option to have five error beeps, there will be five error beeps and five LED flashes in response to an error.
Page 74: Base Or Access Point Address
Base or Access Point Address Scan the bar code below to determine the address of the base or Access Point you are using. Base Address Scanner Modes Your scanner is capable of working in single scanner mode, multiple scanner mode, or with Bluetooth devices other than the charge base or Access Point. Charge Only Mode There may be times when you want to charge your scanner, but not link to the base.
Page 75: Linked Modes
Linked Modes Locked Link Mode and Open Link Mode are the link modes that accommodate dif- ferent applications. Scan the appropriate bar codes included in the Open Link and Locked Link Mode explanations that follow to switch from one mode to another. Default = Open Link Mode.
Page 76: Override Locked Scanner
Override Locked Scanner If you need to replace a broken or lost scanner that is linked to a base or an Access Point, scan the Override Locked Scanner bar code below with a new scanner and place that scanner in the base, or scan the Access Point linking bar code. The locked link will be overridden;...
Page 77: Scanner Power Time-Out Timer
Setting Sound 3 long beeps, medium pitch 3 long beeps, high pitch 4 short beeps, medium pitch 4 short beeps, high pitch single chirps, medium pitch 2 chirps, then 1 chirp, medium pitch single chirps, high pitch 2 chirps, then 1 chirp, high pitch Base Alarm Type Note: Only the CCB01-010BT base has an alarm.
Page 78: Flexible Power Management
0 seconds 200 seconds 400 seconds 900 seconds * 3600 seconds 7200 seconds Note: When the scanner is in power down mode, pull the trigger to power the unit back up. There will be a set of power up beeps and a delay of up to a few seconds for the radio to join.
Page 79: Batch Mode
Access Point once the scanner is back in range or when the records are manually transmitted. Note: Batch Mode is only supported by the Honeywell Charge and Communication Base (CCB) and Honeywell Access Point (AP). Batch mode has limitations when using multiple scanners to one base or Access Point.
Page 80: Batch Mode Beep
the scanner’s buffer space is full, any bar codes scanned generate an error tone. In order to scan bar codes again, the data must be transmitted to the base or Access Point. Once the data is transmitted, it is cleared in the scanner. Persistent Batch Mode is the same as Inventory Batch Mode, except that once the data is transmitted to the base or Access Point, it is retained in the scanner.
Page 81: Batch Mode Quantity
Flash Storage: The scanner writes any untransmitted data to flash memory prior to powering down. The data will still be there when the scanner powers back up. How- ever, the scanner will power down, even with untransmitted data, if it reaches a power down timeout or if the battery power is very low.
Page 82 For example, if the Quantity 5 bar code is scanned after the quantity has been set to 1234, then the 1 is dropped, the quantity will be 2345. Example: Add a quantity of 5 for the last item scanned. 1. Scan the item's bar code. 2.
Page 83: Batch Mode Output Order
Quantity Codes (Continued) Batch Mode Output Order When batch data is transmitted, select whether you want that data sent as FIFO (first-in first-out), or LIFO (last-in first-out). Default = Batch Mode FIFO. * Batch Mode FIFO Batch Mode LIFO Total Records If you wish to output the total number of bar codes scanned when in Batch Mode, scan Total Records.
Page 84: Delete Last Code
Total Records Delete Last Code If you want to delete the last bar code scanned when in Batch Mode, scan Delete Last Code. Delete Last Code Clear All Codes If you want to clear the scanner’s buffer of all data accumulated in Batch Mode, scan Clear All Codes.
Page 85: Multiple Scanner Operation
* Batch Mode Transmit Delay Off (No Delay) Batch Mode Transmit Delay Short (250 ms) Batch Mode Transmit Delay Medium (500 ms) Batch Mode Transmit Delay Long (1000 ms) Multiple Scanner Operation Note: Multiple Scanner Operation Mode allows you to link up to 7 scanners to one base or Access Point.
Page 86 Perform the rename operation using either the bar codes on page 67, or by send- ing the serial command :ScannerName:BT_NAMNewName. where ScannerName is the current name of the scanner, and NewName is the new name for the scanner. If you wish to change the names of additional scanners, link them one at a time and repeat the :ScannerName:BT_NAMNewName.
Page 87: Application Work Groups
You could assign all the scanners in the retail area to one work group and those in the warehouse to another. Consequently, any desired changes to either the retail or warehouse area would apply to all scanners in that particular work group. Honeywell’s online configuration tool, EZConfig-Scanning (page 254), makes it easy for you to program your system for use with multiple scanners and multiple work groups.
Page 88: Reset The Factory Defaults: All Application Work Groups
Group 1 Group 2 Group 3 Group 4 Group 5 Group 6 Reset the Factory Defaults: All Application Work Groups The following bar code defaults all of the work groups to the factory default set- tings. PAPDFT& Factory Default Settings: All Work Groups To see what the factory default settings are, refer to the table of Menu Commands,...
Page 89: Reset The Custom Defaults: All Application Work Groups
The scanner can be used either with the charge base, an Access Point, or with other Bluetooth devices. Those devices include personal computers, laptops, PDAs, and Honeywell mobility systems devices. Bluetooth Secure Simple Pairing (SSP) Secure Simple Pairing (SSP) allows you to connect simply and securely to other...
Page 90: Bluetooth Hid Keyboard Connect
Bluetooth HID Keyboard Connect Your scanner can be paired with Bluetooth-capable devices, such as personal com- puters, laptops, and tablets, so that scanned data appears on your device screen as though it was entered on the keyboard. In order to pair with the Bluetooth device: 1.
Page 91: Virtual Keyboard
Save Virtual Keyboard Once your scanner has been connected directly to an iPad, smart phone, or laptop, you can toggle the virtual keyboard on your device with a quick double pull of the scanner trigger. Bluetooth HID Keyboard Disconnect If your scanner has been connected directly to an iPad, smart phone, or laptop using Bluetooth HID Keyboard Connect (page 70), you must disconnect it in order...
Page 92: Bluetooth Serial Port - Pcs/Laptops
Non-Base BT Connection PDAs/Mobility Systems Devices You may also use the scanner with a PDA or a Honeywell Mobility Systems device. Scan the bar code below and follow the instructions supplied with your Bluetooth device to locate the scanner, and connect with it.
Page 93: Auto Reconnect Mode
Auto Reconnect Mode Auto Reconnect controls whether or not the scanner automatically begins the relink process when a loss of connection is detected. When the Auto Reconnect On bar code is scanned, the scanner begins the relink process immediately, without user intervention.
Page 94: Relink Time-Out
or an Access Point. In order to prevent continuous transmissions that could inter- fere with other users of the ISM band, the number of attempts to connect is limited by this setting. After the maximum number of attempts is reached, the scanner will not attempt to reconnect to a base or an Access Point.
Page 95: Bluetooth/Ism Network Activity Examples
Bluetooth/ISM Network Activity Examples Default values When the scanner goes out of range, the scanner repeatedly attempts to connect to the base unit or Access Point. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time. After one hour, the scanner pow- ers off and batch mode data is lost.
Page 96 feedback to the scan operator. The Host ACK functionality is controlled via a num- ber of pre-defined escape commands that are sent to the scanner to make it behave in different ways. Note: System performance degrades when using Host ACK at rates lower than 9600 baud. The following criteria must be met for the Host ACK to work correctly: •...
Page 97: Host Ack On/Off
• Scanner operation is suspended until 1) a valid escape string is received from the host system or 2) the scanner times out. • Once condition 1 or 2 above has been met, the scanner is ready to scan again, and the process repeats.
Page 98 Command Action [ESC] 7, Beeps to indicate a successful decode and communication to host. [ESC] 8,[ESC] 8, Razz or error tone to indicate a decode/communication to host was unsuccessful. Xenon/Granit User Guide...
Page 99: Chapter 4 - Cordless System Operation: Xenon 1902G-Bf
CHAPTER CORDLESS SYSTEM OPERATION: XENON 1902G-BF Note: This chapter applies only to Xenon 1902g-BF cordless scanning systems. It does not apply to corded scanners, Xenon 1902g/1912, or Granit 1911i/1981i scanners. See Cordless System Operation: Xenon 1902g/1912 and Granit 1911i/1981i beginning on page 41 for other Xenon and Granit cordless scanning systems.
Page 100: Link The Scanner To A Charge Base
Link the Scanner to a Charge Base Xenon Scanner CCB01-010BT-BF Charge Base Page Button and Base LEDs When the base is connected and powered up, put the scanner in the base to estab- lish a link. The green LED on the base flashes to indicate the scanner’s instant charge pack is charging.
Page 101: Communication Between The Cordless System And The Host
Communication Between the Cordless System and the Host The cordless scanner provides immediate feedback in the form of a “good read” indication with a green LED on the scanner and an audible beep. This indicates that the bar code has been scanned correctly and the base has acknowledged receiving the data.
Page 102: System Conditions
The CCB01-010BT-BF (Bluetooth Class 2) provides a communication range of 33 feet (10m) between the scanner and base, depending on the environment. See Flexible Power Management, page 97, for information about controlling this range. System Conditions The components of the cordless system interact in specific ways as you associate a scanner to a base, as you move a scanner out of range and bring a scanner back in range.
Page 103: About The Instant Charge Pack
The instant charge pack must be charged before initial use. When the scanner is not in use, return it to the base. The model CCB01-010BT-BF base is designed for use with the Honeywell model Xenon 1902g-BF scanner.
Page 104: Scanner
Scanner Scanner Communication and Scanning The following feedback is provided by the scanner and indicates communication and scanning status. LED Indication Beeper Indication Cause Normal Operation Red Flash None Charge pack low Green Flash 1 beep Successful communication or linking Red, blinking Razz or error tone Failed communication...
Page 105: Low Power Alert Range
Low Power Alert Range Set the power range that will trigger a low power alert. Default = 10-30%. *Low Power Alert 10-30% Low Power Alert 10-50% Low Power Alert Flash Number You can program the scanner’s LEDs to flash up to 9 times for the low power alert. If the Low Power Alert Beep (page 86) is on, a double beep will sound with each...
Page 106: Low Power Alert Beep
Interval Between Alerts If you have set the Low Power Alert Repeat (page 85) to more than 1, you can set the length of time, in seconds, between the low power alerts. To set this interval, scan the bar code below and then scan a digit (10-120) bar code from the Programming Chart, beginning on page 341, then Save.
Page 107: Base Charge Status
Red LED - Host Communication Communication Red LED Condition Short blinks in multiple pulses. Occurs while transferring Receiving/sending data data to/from the RF module or the host port. Base Charge Status When charging, the base indicates the progress while the scanner resides in the base.
Page 108: Base Charge Modes
Base Charge Modes When the base has both an external power supply (plugged into the auxiliary power port) and a host interface cable, it will draw its power from the external power sup- ply. When the base does not have an external power supply, it draws its power from the interface cable.
Page 109: Page Button With Scanner In The Base
When the scanner is out of the base, press the page button on the base to make the associated scanner start beeping (3 short and 1 long beep). If you pull the trigger on a scanner that is beeping in response, or press the Page button on the base a second time, the scanner stops beeping.
Page 110: Scan While In Base Cradle
Scan While in Base Cradle If you want to be able to scan bar codes while the scanner is in the base cradle, scan the Scan in Cradle On bar code below. If you want to only allow scanning when the scanner is out of the base cradle, scan Scan in Cradle Off. If you want the scanner to shut down when in the base cradle, scan Shut Down Scanner in Cradle.
Page 111: Page Pitch
Page Pitch When the scanner is out of the base and you press the Page button, the scanner associated with that base begins beeping. You can set the pitch of the paging beep for the scanner by scanning one of the following bar codes. Default = Low. * Low (1000 Hz) Medium (3250 Hz) High (4200 Hz)
Page 112: Number Of Beeps - Base Error
* Razz (250 Hz) Medium (3250 Hz) High (4200 Hz) Number of Beeps - Base Error The number of beeps and LED flashes emitted by the base for an error condition can be programmed from 1 - 9. For example, if you program this option to have five error beeps, there will be five error beeps and five LED flashes in response to an error.
Page 113: Base Address
Base Address Scan the bar code below to determine the address of the base you are using. Base Address Scanner Modes Charge Only Mode There may be times when you want to charge your scanner, but not link to the base. In order to program the base for Charge Only Mode, you must link the scanner to it.
Page 114: Unlink The Scanner
Locked Link Mode - Single Scanner If you link a scanner to a base using the Locked Link Mode, other scanners are blocked from being linked if they are inadvertently placed into the base. If you do place a different scanner into a base, it will charge the scanner, but the scanner will not be linked.
Page 115: Override Locked Scanner
Override Locked Scanner If you need to replace a broken or lost scanner that is linked to a base, scan the Override Locked Scanner bar code below with a new scanner and place that scan- ner in the base. The locked link is overridden, the broken or lost scanner’s link with the base is removed, and the new scanner is linked to the base.
Page 116: Scanner Power Time-Out Timer
Setting Sound 4 short beeps, high pitch single chirps, medium pitch 2 chirps, then 1 chirp, medium pitch single chirps, high pitch 2 chirps, then 1 chirp, high pitch Base Alarm Type Scanner Alarm Type Scanner Power Time-Out Timer When there is no activity within a specified time period, the scanner enters low power mode.
Page 117: Flexible Power Management
0 seconds 200 seconds * 400 seconds 900 seconds 3600 seconds 7200 seconds Note: When the scanner is in power down mode, pull the trigger to power the unit back up. There will be a set of power up beeps and a delay of up to a few seconds for the radio to join.
Page 118: Batch Mode
Full Power * Medium High Power Medium Power Low Power Batch Mode Batch mode is used to store bar code data when a scanner is out of range of its base, or when performing inventory. The data is transmitted to the base once the scanner is back in range or when the records are manually transmitted.
Page 119: Batch Mode Beep
Automatic Batch Mode Inventory Batch Mode Persistent Batch Mode Batch Mode Beep When scanning in Inventory Batch Mode (page 99), the scanner beeps every time a bar code is scanned. When Batch Mode Beep is On, you will also hear a click when each bar code is sent to the host.
Page 120: Batch Mode Quantity
RAM Storage Batch Mode Quantity When in Batch Mode, you may wish to transmit the number of multiple bar codes scanned, rather than a single bar code multiple times. For example, if you scan three bar codes called XYZ with Batch Mode Quantity Off, when you transmit your data it will appear as XYZ three times.
Page 121 5. Scan the quantity 0 bar code. Example: Change a quantity of 103 to 10. To correct an incorrect quantity, scan the quantity 0 bar code to replace the incor- rect digits, then scan the correct quantity bar codes. 1. Scan the quantity 0 bar code to change the quantity to 1030. 2.
Page 122: Batch Mode Output Order
Quantity Codes (Continued) Batch Mode Output Order When batch data is transmitted, select whether you want that data sent as FIFO (first-in first-out), or LIFO (last-in first-out). Default = Batch Mode FIFO. * Batch Mode FIFO Batch Mode LIFO Total Records If you wish to output the total number of bar codes scanned when in Batch Mode, scan Total Records.
Page 123: Clear All Codes
Clear All Codes If you want to clear the scanner’s buffer of all data accumulated in Batch Mode, scan Clear All Codes. Clear All Codes Transmit Records to Host If you are operating in Inventory Batch Mode (see Inventory Batch Mode on page 99), you must scan the following bar code to transmit all the stored data to the host system.
Page 124: Scanner Name
Scanner Name You may assign a name to each scanner you are using for identification purposes. The default name is in the format “ScannerName_Model_SN_XXXXXXXXXX” Per- form the rename operation using either the bar codes on page 105, or by sending the serial command :ScannerName:BT_NAMNewName.
Page 125: Change The Scanner's Bluetooth Pin Code
You may also scan the Scanner Name bar code below and scan a number for the scanner name. For example, if you wanted to name the linked scanner “312,” you would scan the bar code below, scan the 3, 1, and 2 bar codes on the Programming Chart, beginning on page 341, then Save.
Page 126: Maximum Link Attempts
The table below shows the results of the Auto Reconnect On and Off settings: Event Auto Reconnect On Auto Reconnect Off Scanner out of range Relink occurs automatically. If The scanner is relinked by maximum number of link attempts pulling the trigger. is unsuccessful, then the scanner must be relinked by either pulling the trigger or placing the scanner...
Page 127: Relink Time-Out
Relink Time-Out Relink Time-Out controls the idle time between relink attempts. An attempt to link a scanner to a base typically lasts up to 5 seconds. This is the time when the scan- ner is actually attempting a contact. Relink Time-Out controls the amount of time, in seconds, that elapses between the end of one connection attempt and the start of the next.
Page 128: Host Acknowledgment
base, but retains any bar codes that may have been saved in batch mode. After one hour, the scanner powers off and batch mode data is lost. Refer to Auto Reconnect Mode, page 105, to review other events that can start the relink process. Example: Auto Reconnect Mode set to 1 Maximum Link Attempts set to 0 Relink Time-Out set to 10...
Page 129: Host Ack On/Off
[ESC]7, is sent from the host to the scanner for an on-file product [ESC]8,[ESC]8, is sent from the host to the scanner for a not-on-file product When a bar code is scanned, the scanner enters a timeout period until either the host ACK sequence is received, or the timeout expires (in 10 seconds, by default).
Page 130: Host Ack Responses
Host ACK Responses Command Action [ESC] a, Double beeps to indicate a successful menu change was made. [ESC] b, Razz or error tone to indicate a menu change was unsuccessful. [ESC] 1, The green LED illuminates for 135 milliseconds followed by a pause. [ESC] 2, The green LED illuminates for 2 seconds followed by a pause.
Page 131: Chapter 5 - Input/Output Settings
CHAPTER INPUT/OUTPUT SETTINGS Power Up Beeper Note: This feature does not apply to the CCB02-100BT/CCB05-100BT base. The scanner can be programmed to beep when it’s powered up. If you are using a cordless system, the base can also be programmed to beep when it is powered up. Scan the Off bar code(s) if you don’t want a power up beep.
Page 132: Beep On Bel Character
Beep on BEL Character You may wish to force the scanner to beep upon a command sent from the host. If you scan the Beep on BEL On bar code below, the scanner will beep every time a BEL character is received from the host. Default = Beep on BEL Off. *Beep on BEL Off Beep on BEL On Trigger Click...
Page 133: Beeper Volume - Good Read
Beeper Volume – Good Read The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High for Granit/Xenon, Low for Xenon HC. * Low Medium * High Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read.
Page 134: Beeper Pitch - Error
The scanner vibrates once when a bar code is successfully read, and twice when a programming bar code is successfully read. When a programming bar code is unsuccessful, the scanner emits one long vibration (2 times the Vibrate Duration length). Scan Vibrate - Good Read Off to keep the scanner from vibrating. Default = Vibrate - Good Read On.
Page 135: Beeper Duration - Good Read
Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read. Default = Normal. * Normal Beep Short Beep Short Beep LED – Good Read The LED indicator can be programmed On or Off in response to a good read. Default = On.
Page 136: Beeper Volume Max
to an error. To change the number of error beeps, scan the bar code below and then scan a digit (1-9) bar code from the Programming Chart, beginning on page 341, then Save. Default = 1. Number of Error Beeps/LED Flashes Beeper Volume Max Note: The Beeper Volume Max feature only applies to Granit products.
Page 137: User-Specified Good Read Delay
Enhanced Trigger Toggle Note: Only the Xenon 1900 and 1902 support Trigger Toggle mode. Trigger Toggle mode lets you quickly hit the trigger 2 or 3 times to put the scanner into either imaging mode, cell phone read mode, or centering mode, then toggle back to scanning.
Page 138 *Trigger Toggle Off Trigger Toggle - Image Capture Trigger Toggle - Cell Phone Read Trigger Toggle - Centering Trigger Number This sets the number of trigger preses required to activate the Trigger Toggle Mode. 2 Quick Triggers 3 Quick Triggers 4 Quick Triggers Trigger Timing This sets the timing of the trigger presses in order to qualify as a trigger toggle,...
Page 139: Serial Trigger
Trigger Toggle Timeout This sets the length of time the scanner stays in trigger toggle mode before revert- ing to scan mode. After scanning the Trigger Toggle Timeout bar code, set the time-out duration (from 0 to 65 seconds) by scanning digits from the Programming Chart, beginning on page 341, then Save.
Page 140: Presentation Mode
Presentation Mode Presentation Mode uses ambient light and scanner illumination to detect bar codes. When in Presentation Mode, the LEDs remain dim until a bar code is pre- sented to the scanner, then the aimer turns on and the LEDs turn up to read the code.
Page 141: Presentation Centering
Presentation Centering Use Presentation Centering to narrow the scanner’s field of view when it is in the stand to make sure the scanner reads only those bar codes intended by the user. For instance, if multiple codes are placed closely together, Presentation Centering will insure that only the desired codes are read.
Page 142: In-Stand Sensor Mode
Presentation Centering Window Right of Presentation Centering Window In-Stand Sensor Mode Note: The In-Stand Sensor feature only applies to Xenon 1900, 1900h, 1910, 1902, 1902h, and 1912products. It does not apply to the Xenon 1902g-BF or Granit products. Xenon/Granit User Guide...
Page 143: Poor Quality Codes
This feature senses when the scanner is removed from the stand and tells it to begin manual triggering. When Sensor On is enabled, the scanner defaults to Streaming Presentation Mode when it is in the stand, and to Manual Trigger Mode when it is removed from the stand.
Page 144: Codegate
piness is decreased, making it less aggressive when reading good quality bar codes. This setting does not affect 1D bar code reading. Default = Poor Quality PDF Reading Off. Poor Quality PDF Reading On * Poor Quality PDF Reading ® CodeGate When CodeGate is On, the trigger is used to allow decoded data to be transmitted to the host system.
Page 145: Streaming Presentation In-Stand
Streaming Presentation Mode - Normal Streaming Presentation Mode - Enhanced When using Preferred Symbology (page 5-134), a lower priority symbol must be centered on the aiming pattern to be read in Streaming Presentation Mode. Note: If you are using a cordless charge base, it must have an external power supply plugged into the aux port for Streaming Presentation to work properly.
Page 146: Hands Free Time-Out
Hands Free Time-Out The Scan Stand and Presentation Modes are referred to as “hands free” modes. If the scanner’s trigger is pulled when using a hands free mode, the scanner changes to manual trigger mode. You can set the time the scanner should remain in manual trigger mode by setting the Hands Free Time-Out.
Page 147: User-Specified Reread Delay
User-Specified Reread Delay If you want to set your own length for the reread delay, scan the bar code below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 341, then Save. User-Specified Reread Delay 2D Reread Delay Sometimes 2D bar codes can take longer to read than other bar codes.
Page 148: Activation Character
mitted. Scan the following On bar code to use character activation, then use Activation Character (page 128) to select the character you will send from the host to start scanning. Default = Off. * Off Activation Character This sets the character used to trigger scanning when using Character Activation Mode.
Page 149: Character Activation Timeout
Character Activation Timeout You can set a timeout for the length of time the illumination remains on and attempting to decode bar codes when using Character Activation Mode. Set the length (in milliseconds) for a timeout by scanning the following bar code, then set- ting the timeout (from 1-300,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 341, then Save.
Page 150: Illumination Lights
Illumination Lights If you want the illumination lights on while reading a bar code, scan the Lights On bar code, below. However, if you want to turn just the lights off, scan the Lights Off bar code. Default = Lights On. Note: This setting does not affect the aimer light.
Page 151: User-Specified Aimer Delay
User-Specified Aimer Delay If you want to set your own length for the duration of the delay, scan the bar code below, then set the time-out by scanning digits (0 - 4,000 ms) from the Programming Chart, beginning on page 341, then Save. Delay Duration Aimer Mode This feature allows you to turn the aimer on and off.
Page 152: Single Code Centering
Single Code Centering Scan Single Code Centering to target the bar code closest to the center of the image. Singling out a bar code in this manner increases scanning accuracy when there are multiple bar codes close together. Single Code Centering Custom Centering Use the following settings to customize your centering window.
Page 153 that pass through the centering window you specify using the Top of Centering Window, Bottom of Centering Window, Left, and Right of Centering Window bar codes. Example: In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right, 8% top, and 25% bottom.
Page 154: Preferred Symbology
Top of Centering Window Bottom of Centering Window Left of Centering Window Right of Centering Window Preferred Symbology The scanner can be programmed to specify one symbology as a higher priority over other symbologies in situations where both bar code symbologies appear on the same label, but the lower priority symbology cannot be disabled.
Page 155: High Priority Symbology
* Preferred Symbology Off High Priority Symbology To specify the high priority symbology, scan the High Priority Symbology bar code below. On the Symbology Charts on page 327, find the symbology you want to set as high priority. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart, beginning on page 341, then Save.
Page 156: Preferred Symbology Default
Preferred Symbology Default Scan the bar code below to set all Preferred Symbology entries to their default val- ues. Preferred Symbology Default Output Sequence Overview Output Sequence Editor This programming selection allows you to program the scanner to output data (when scanning more than one symbol) in whatever order your application requires, regardless of the order in which the bar codes are scanned.
Page 157: Other Programming Selections
5. End Output Sequence Editor Scan F F to enter an Output Sequence for an additional symbology, or Save to save your entries. Other Programming Selections Discard exits without saving any Output Sequence changes. Output Sequence Example In this example, you are scanning Code 93, Code 128, and Code 39 bar codes, but you want the scanner to output Code 39 1st, Code 128 2nd, and Code 93 3rd, as shown below.
Page 158: Output Sequence Editor
start character match for Code 93, 43h = “C” termination string for third code To program the previous example using specific lengths, you would have to count any programmed prefixes, suffixes, or formatted characters as part of the length. If you use the example on page 137, but assume a <CR>...
Page 159: Require Output Sequence
Scan Discard Partial Sequence to discard partial sequences when the output sequence operation is terminated before completion. Scan Transmit Partial Sequence to transmit partial sequences. (Any fields in the sequence where no data match occurred are skipped in the output.) Transmit Partial Sequence * Discard Partial Sequence Require Output Sequence...
Page 160: No Read
scanner attempts to find and decode new symbols as long as the trigger is pulled. When this programming selection is turned Off, the scanner will only read the sym- bol closest to the aiming beam. Default = Off. * Off No Read With No Read turned On, the scanner notifies you if a code cannot be read.
Page 161: Working Orientation
Video Reverse Only Video Reverse and Standard Bar Codes * Video Reverse Off Working Orientation Some bar codes are direction-sensitive. For example, KIX codes and OCR can mis- read when scanned sideways or upside down. Use the working orientation settings if your direction-sensitive codes will not usually be presented upright to the scan- ner.
Page 162 Vertical, Bottom to Top Upside Down Vertical, Top to Bottom Xenon/Granit User Guide...
Page 163: Chapter 6 - Healthcare Settings
CHAPTER HEALTHCARE SETTINGS The following settings have been developed to enhance scanning in a healthcare environment. These settings are only supported by the Xenon 1900h scanner and Xenon 1902h scanner and base. They allow you to set quickly configure streaming presentation, and to set the scanner and base to quiet modes for scanning that do not disturb resting patients.
Page 164: Silent Mode With Long Led
Silent Mode with Long LED Scan the following bar code to completely silence the Xenon 1900h scanner or Xenon 1902h scanner and base. The scanner beep, base beep, base and scanner power up beep, and scanner linking sounds are all silenced. When a bar code is scanned, the LED and aimer remain solidly lit for 1 second.
Page 165: Low Beeper (Daytime Mode)
Low Beeper (Daytime Mode) The following bar code sets all sounds to on, but at a low volume. The scanner beep, base beep, base and scanner power up beep, and scanner linking sounds are all set to low volume. Daytime Mode - Cordless Scanner and Base Daytime Mode - Corded Scanner...
Page 166: Number Of Led Flashes
Number of LED Flashes If you have silenced the scanner’s beeper, you may set the number of times the LED flashes when reading bar codes. Default = 1 LED Flash. Note: If you have set LED Solid (No Flash) (page 147), to anything but Off, that setting will override the LED Flash settings.
Page 167: Led Solid (No Flash)
LED Solid (No Flash) Under normal operations, the scanner’s LED flashes once for a good read. You may set the LED to remain on for a length of time after a good read instead of flashing. Default = LED Solid Off (Resume Flash). * LED Solid Off (Resume Flash) LED Solid 1 Second...
Page 168: Out-Of-Range Alarm Volume
Page Volume Medium Page Volume High Out-of-Range Alarm Volume Note: This setting is not supported by the Xenon 1900h scanner. If your scanner is out range of the base, an alarm sounds from both your base and scanner. If your scanner is out range of an Access Point, an alarm sounds from just the scanner.
Page 169: Out-Of-Range Delay
Scanner Alarm Volume Medium Base Alarm Volume High Scanner Alarm Volume High Out-of-Range Delay Note: This setting is not supported by the Xenon 1900h scanner. When using the Out-of-Range Alarm settings, the length of the delay for the alarm is set with an Out-of-Range Delay. When the scanner is out of range of the base or Access Point, the alarm will delay for a set length of time before going off.
Page 170 Xenon/Granit User Guide...
Page 171: Chapter 7 - Data Edit
CHAPTER DATA EDIT Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string.
Page 172: Add A Prefix Or Suffix
• When setting up for specific symbologies (as opposed to all symbologies), the specific symbology ID value counts as an added prefix or suffix character. • The maximum size of a prefix or suffix configuration is 200 characters, which includes header information. Add a Prefix or Suffix: Step 1.
Page 173: Add A Carriage Return Suffix To All Symbologies
Step 1. Scan the Clear One Prefix or Clear One Suffix symbol. Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in Symbology Charts, beginning on page 327) for the symbology from which you want to clear the prefix or suffix. Step 3.
Page 174: Function Code Transmit
Clear All Suffixes Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are provided in ASCII Conversion Chart (Code Page 1252), beginning on page 330.
Page 175: User Specified Intercharacter Delay
To remove this delay, scan the Intercharacter Delay bar code, then set the number of delays to 0. Scan the Save bar code from the Programming Chart, beginning on page 341. Note: Intercharacter delays are not supported in USB serial emulation. User Specified Intercharacter Delay An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed after the transmission of a particular character of scanned data.
Page 176: Intermessage Delay
To remove this delay, scan the Interfunction Delay bar code, then set the number of delays to 0. Scan the Save bar code from the Programming Chart, beginning on page 341. Intermessage Delay An intermessage delay of up to 5000 milliseconds (in 5ms increments) may be placed between each scan transmission.
Page 177: Chapter 8 - Data Format
CHAPTER DATA FORMAT Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output.
Page 178: Add A Data Format
If you have changed data format settings, and wish to clear all formats and return to the factory defaults, scan the Default Data Format code below. * Default Data Format Add a Data Format Step 1. Scan the Enter Data Format symbol (page 159).
Page 179: Other Programming Selections
Step 7. Scan Save to save your data format, or Discard to exit without saving your changes. Enter Data Format Save Discard Other Programming Selections • Clear One Data Format This deletes one data format for one symbology. If you are clearing the primary format, scan 0 from the Programming Chart, beginning on page 341.
Page 180: Terminal Id Table
Terminal ID Table Terminal Model(s) Terminal ID PC keyboard (HID) Mac Keyboard PC Keyboard (Japanese) Serial (COM driver required) HID POS USB SurePOS Handheld USB SurePOS Tabletop Serial RS232 TTL RS232 True RS485 (IBM-HHBCR 1+2, 46xx) Keyboard PS2 compatibles AT compatibles Data Format Editor Commands When working with the Data Format Editor, a virtual cursor is moved along your input data string.
Page 181 F2 Example: Send a number of characters Send the first 10 characters from the bar code above, followed by a carriage return. Command string: F2100D F2 is the “Send a number of characters” command 10 is the number of characters to send 0D is the hex value for a CR The data is output as: 1234567890 F2 and F1 Example: Split characters into 2 lines...
Page 182 Using the bar code above, send all characters up to but not including “D,” followed by a carriage return. Command string: F3440D F3 is the “Send all characters up to a particular character” command 44 is the hex value for a 'D” 0D is the hex value for a CR The data is output as: 1234567890ABC...
Page 183 Insert a character multiple times F4 Send “xx” character “nn” times in the output message, leaving the cursor in the current position. Syntax = F4xxnn where xx stands for the insert character’s hex value for its ASCII code, and nn is the numeric value (00-99) for the number of times it should be sent.
Page 184 1234567890**ABCDEFGHIJ <CR> Insert symbology name B3 Insert the name of the bar code’s symbology in the output message, without moving the cursor. Only symbologies with a Honeywell ID are included (see Symbology Charts on page 327). Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 330 for decimal, hex and character codes.
Page 185: Move Commands
0D is the hex value for a CR The data is output as: Code128 20 1234567890ABCDEFGHIJ <CR> Insert key strokes B5 Insert a key stroke or combination of key strokes. Key strokes are dependent on your keyboard (see Keyboard Key References on page 337).
Page 186 Move the cursor forward 3 characters, then send the rest of the bar code data from the bar code above. End with a carriage return. Command string: F503F10D F5 is the “Move the cursor forward a number of characters” command 03 is the number of characters to move the cursor F1 is the “Send all characters”...
Page 187: Search Commands
Move the cursor to the end EA Move the cursor to the last character in the input message. Syntax = EA. Search Commands Search forward for a character F8 Search the input message forward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx”...
Page 188 Search forward for a string B0 Search forward for “s” string from the current cursor position, leaving cursor pointing to “s” string. Syntax = B0nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B0000454657374 will search forward for the first occurrence of the 4 character string “Test.”...
Page 189: Miscellaneous Commands
Search forward for a non-matching character E6 Search the input message forward for the first non-“xx” character from the current cursor position, leaving the cursor pointing to the non-“xx” character. Syntax = E6xx where xx stands for the search character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 330 for decimal, hex and character codes.
Page 190 FB Example: Remove spaces in bar code data This example shows a bar code that has spaces in the data. You may want to remove the spaces before sending the data. Using the bar code above: Command string: FB0120F10D FB is the “Suppress characters” command 01 is the number of character types to be suppressed 20 is the hex value for a space F1 is the “Send all characters”...
Page 191 0D is the hex value for a CR (the character that will replace the 0) F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: 1234 5678 <CR> Stop replacing characters E5 Terminates character replacement.
Page 192 If this bar code is read, the next data format, if there is one, will be used on the data. If there is no other format, the format fails and the raw data is output as AB1234. If this bar code is read: the data is output as: 1234AB <CR>...
Page 193: Data Formatter
Discard Data B8 Discards types of data. For example, you may want to discard Code 128 bar codes that begin with the letter A. In step 4 (page 158), select 6A (for Code 128), and in step 5, select 9999 (for all lengths). Enter FE41B8 to compare and discard Code 128 bar codes that begin with the letter A.
Page 194: Data Format Non-Match Error Tone
Any data that does not match your data format requirements generates an error tone. If you wish to process this type of bar code without generating an error tone, see Data Format Non-Match Error Tone. Choose one of the following options. Default = Data Formatter On, Not Required, Keep Prefix/Suffix.
Page 195: Primary/Alternate Data Formats
Primary/Alternate Data Formats You can save up to four data formats, and switch between these formats. Your pri- mary data format is saved under 0. Your other three formats are saved under 1, 2, and 3. To set your device to use one of these formats, scan one of the bar codes below.
Page 196 Single Scan-Data Format 3 Xenon/Granit User Guide...
Page 197: Chapter 9 - Symbologies
CHAPTER SYMBOLOGIES This programming section contains the following menu selections. Refer to Chapter 12 for settings and defaults. • All Symbologies • Interleaved 2 of 5 • Aztec Code • Korea Post • China Post (Hong Kong 2 of 5) •...
Page 198: All Symbologies
All Symbologies If you want to decode all the symbologies allowable for your scanner, scan the All Symbologies On code. If on the other hand, you want to decode only a particular symbology, scan All Symbologies Off followed by the On symbol for that particular symbology.
Page 199: Codabar
Codabar <Default All Codabar Settings> Codabar On/Off * On Codabar Start /Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Trans- mit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.”...
Page 200: Codabar Concatenation
When Check Character is set to Validate, but Don’t Transmit, the unit will only read Codabar bar codes printed with a check character, but will not transmit the check character with the scanned data. * No Check Character Validate Modulo 16, but Don’t Transmit Validate Modulo 16 and Transmit...
Page 201: Code 39
Codabar Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 178) for additional information. Minimum and Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60. Minimum Message Length Maximum Message Length Code 39 <...
Page 202: Code 39 Message Length
* Don’t Transmit Code 39 Check Character No Check Character indicates that the scanner reads and transmits bar code data with or without a check character. When Check Character is set to Validate, but Don’t Transmit, the unit only reads Code 39 bar codes printed with a check character, but will not transmit the check character with the scanned data.
Page 203: Code 39 Append
Code 39 Append This function allows the scanner to append the data from several Code 39 bar codes together before transmitting them to the host computer. When the scanner encounters a Code 39 bar code with the append trigger character(s), it buffers Code 39 bar codes until it reads a Code 39 bar code that does not have the append trigger.
Page 204: Code 39 Code Page
Full ASCII Table (Continued) BEL $G ETB $W ‘ CAN $X HT $I EM $Y SUB $Z ESC %A < CR $M GS %C SO $N > US %E DEL %T Character pairs /M and /N decode as a minus sign and period respectively. Character pairs /P through /Y decode as 0 through 9.
Page 205: Interleaved 2 Of 5
Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 On/Off * On Check Digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads Inter- leaved 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data.
Page 206: Interleaved 2 Of 5 Message Length
Interleaved 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 178) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 6, Maximum Default = 80. Minimum Message Length Maximum Message Length NEC 2 of 5...
Page 207: Nec 2 Of 5 Message Length
When Check Digit is set to Validate and Transmit, the scanner only reads NEC 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit...
Page 208: Code 93 Code Page
Code 93 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 178) for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 93 Append This function allows the scanner to append the data from several Code 93 bar...
Page 209: Straight 2 Of 5 Industrial (Three-Bar Start/Stop)
Character Replacements on page 334), and scan the value and the Save bar code from the Programming Chart, beginning on page 341. The data characters should then appear properly. Code 93 Code Page Straight 2 of 5 Industrial (three-bar start/stop) <Default All Straight 2 of 5 Industrial Settings>...
Page 210: Straight 2 Of 5 Iata (Two-Bar Start/Stop)
Straight 2 of 5 IATA (two-bar start/stop) <Default All Straight 2 of 5 IATA Settings> Straight 2 of 5 IATA On/Off * Off Straight 2 of 5 IATA Redundancy If you are encountering errors when reading Straight 2 of 5 IATA bar codes, you may want to adjust the redundancy count.
Page 211: Matrix 2 Of 5
Matrix 2 of 5 <Default All Matrix 2 of 5 Settings> Matrix 2 of 5 On/Off * Off Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 178) for additional information. Minimum and Maximum lengths = 1-80.
Page 212: Check Digits Required
Code 11 <Default All Code 11 Settings> Code 11 On/Off * Off Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits. One Check Digit * Two Check Digits Code 11 Message Length Scan the bar codes below to change the message length.
Page 213: Code 128
Code 128 <Default All Code 128 Settings> Code 128 On/Off * On If you are reading Code 128 bar codes, Codablock F should remain disabled. If you are enabling Codablock F (see Codablock F on page 214), you should disable Code 128.
Page 214: Code 128 Message Length
the higher the redundancy count, the longer it will take to decode the bar code. To adjust the redundancy, scan the Code 128 Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart, beginning on page 341.
Page 215: Gs1-128
Character Replacements on page 334), and scan the value and the Save bar code from the Programming Chart, beginning on page 341. The data characters should then appear properly. Code 128 Code Page GS1-128 <Default All GS1-128 Settings> GS1-128 On/Off * On GS1-128 Message Length Scan the bar codes below to change the message length.
Page 216: Telepen
Telepen <Default All Telepen Settings> Telepen On/Off * Off Telepen Output Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII (start/stop pattern 1). When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and decodes them as compressed numeric with optional full ASCII (start/stop pat- tern 2).
Page 217: Upc-A
Maximum Message Length UPC-A <Default All UPC-A Settings> UPC-A On/Off * On Note: To convert UPC-A bar codes to EAN-13, see Convert UPC-A to EAN-13 on page 204. UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.
Page 218 UPC-A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the begin- ning of the scanned data, but the unit can be programmed so it will not transmit it (Off). Default = On. * On UPC-A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-A data.
Page 219: Upc-A/Ean-13 With Extended Coupon Code
* Not Required Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-A Addenda Required.
Page 220: Coupon Gs1 Databar Output
If you scan the Require Concatenation code, the scanner must see and read the coupon code and extended coupon code in a single read to transmit the data. No data is output unless both codes are read. Default = Off. * Off Allow Concatenation Require Concatenation...
Page 221: Upc-E0
UPC-E0 <Default All UPC-E Settings> UPC-E0 On/Off Most U.P.C. bar codes lead with the 0 number system. To read these codes, use the UPC-E0 On selection. If you need to read codes that lead with the 1 number sys- tem, use UPC-E1 (page 203).
Page 222 Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-E0 Addenda Required.
Page 223: Upc-E1
UPC-E0 Leading Zero This feature allows the transmission of a leading zero (0) at the beginning of scanned data. To prevent transmission, scan Off. Default = On. * On UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda.
Page 224: Ean/Jan-13
* UPC-E1 Off EAN/JAN-13 <Default All EAN/JAN Settings> EAN/JAN-13 On/Off * On Convert UPC-A to EAN-13 When UPC-A Converted to EAN-13 is selected, UPC-A bar codes are converted to 13 digit EAN-13 codes by adding a zero to the front. When Do not Convert UPC-A is selected, UPC-A codes are read as UPC-A.
Page 225 EAN/JAN-13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit Addenda.
Page 226: Ean/Jan-13 Addenda Separator
Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-E0 Addenda Required.
Page 227: Ean/Jan-8
EAN/JAN-8 <Default All EAN/JAN-8 Settings> EAN/JAN-8 On/Off * On EAN/JAN-8 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On EAN/JAN-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data.
Page 228 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-8 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-8 bar codes that have addenda. Default = Not Required. Required * Not Required Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-E0 Addenda...
Page 229: Msi
<Default All MSI Settings> MSI On/Off * Off MSI Check Character Different types of check characters are used with MSI bar codes. You can program the scanner to read MSI bar codes with Type 10 check characters. Default = Validate Type 10, but Don’t Transmit. When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI bar codes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned data.
Page 230: Msi Message Length
Validate 2 Type 10 Characters, but Don’t Transmit Validate 2 Type 10 Characters and Transmit Validate Type 11 then Type 10 Character, but Don’t Transmit Validate Type 11 then Type 10 Character and Transmit Disable MSI Check Characters MSI Message Length Scan the bar codes below to change the message length.
Page 231: Gs1 Databar Omnidirectional
GS1 DataBar Omnidirectional < Default All GS1 DataBar Omnidirectional Settings > GS1 DataBar Omnidirectional On/Off * On GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited On/Off * On Xenon/Granit User Guide...
Page 232: Gs1 Databar Expanded
GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off * On GS1 DataBar Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 178) for additional information. Minimum and Maximum lengths = 4-74.
Page 233: Codablock A
Codablock A <Default All Codablock A Settings> Codablock A On/Off * Off If you are reading Code 39 bar codes, Codablock A should remain disabled. If you are enabling Codablock A, you should disable Code 39 (see Code 39 on page 181). Codablock A Message Length Scan the bar codes below to change the message length.
Page 234: Codablock F
Codablock F <Default All Codablock F Settings> Codablock F On/Off * Off If you are reading Code 128 bar codes, Codablock F should remain disabled. If you are enabling Codablock F, you should disable Code 128 (see Code 128 on page 193).
Page 235: Pdf417
*Off PDF417 < Default All PDF417 Settings > PDF417 On/Off * On PDF417 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 178) for additional information. Minimum and Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750. Minimum Message Length Maximum Message Length Xenon/Granit User Guide...
Page 236: Macropdf417
MacroPDF417 MacroPDF417 is an implementation of PDF417 capable of encoding very large amounts of data into multiple PDF417 bar codes. When this selection is enabled, these multiple bar codes are assembled into a single data string. Default = On. * On MicroPDF417 <...
Page 237: Gs1 Composite Codes
Maximum Message Length GS1 Composite Codes Linear codes are combined with a unique 2D composite component to form a new class called GS1 Composite symbology. GS1 Composite symbologies allow for the co-existence of symbologies already in use. Default = Off. * Off UPC/EAN Version Scan the UPC/EAN Version On bar code to decode GS1 Composite symbols that...
Page 238: Gs1 Emulation
Maximum Message Length GS1 Emulation The scanner can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, ITF-14, GS1- 128, and GS1-128 DataBar and GS1 Composites.
Page 239: Tcif Linked Code 39 (Tlc39)
TCIF Linked Code 39 (TLC39) This code is a composite code since it has a Code 39 linear component and a MicroPDF417 stacked code component. All bar code readers are capable of read- ing the Code 39 linear component. The MicroPDF417 component can only be decoded if TLC39 On is selected.
Page 240 Maximum Message Length QR Code Append This function allows the scanner to append the data from several QR Code bar codes together before transmitting them to the host computer. When the scanner encounters an QR Code bar code with the append trigger character(s), it buffers the number of QR Code bar codes determined by information encoded in those bar codes.
Page 241: Data Matrix
Data Matrix < Default All Data Matrix Settings > Data Matrix On/Off * On Data Matrix Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 178) for additional information. Minimum and Maximum lengths = 1-3116.
Page 242: Maxicode
Data Matrix Code Page Data Matrix Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting.
Page 243: Aztec Code
MaxiCode Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 178) for additional information. Minimum and Maximum lengths = 1-150. Minimum Default = 1, Maximum Default = 150. Minimum Message Length Maximum Message Length Aztec Code <...
Page 244: Chinese Sensible (Han Xin) Code
Aztec Append This function allows the scanner to append the data from several Aztec bar codes together before transmitting them to the host computer. When the scanner encounters an Aztec bar code with the append trigger character(s), it buffers the number of Aztec bar codes determined by information encoded in those bar codes.
Page 245: Postal Codes - 2D
* Off Han Xin Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 178) for additional information. Minimum and Maximum lengths = 1-7833. Minimum Default = 1, Maximum Default = 7833. Minimum Message Length Maximum Message Length Postal Codes - 2D...
Page 246: Combination 2D Postal Codes
Intelligent Mail Bar Code On Japanese Post On KIX Post On Planet Code On Also see Planet Code Check Digit, page 229. Postal-4i On Postnet On Postnet On Also see Postnet Check Digit, page 229. Postnet with B and B’ Fields On InfoMail On Combination 2D Postal Codes: InfoMail and British...
Page 247 Intelligent Mail Bar Code and Postnet with B and B’ Fields On Postnet and Postal-4i On Postnet and Intelligent Mail Bar Code On Postal-4i and Intelligent Mail Bar Code On Postal-4i and Postnet with B and B’ Fields On Planet Code and Postnet On Planet Code and Postnet with B and B’...
Page 248 Planet Code, Postnet, and Intelligent Mail Bar Code On Planet Code, Postal-4i, and Intelligent Mail Bar Code On Postnet, Postal-4i, and Intelligent Mail Bar Code On Planet Code, Postal-4i, and Postnet with B and B’ Fields On Planet Code, Intelligent Mail Bar Code, and Postnet with B and B’...
Page 249: Planet Code Check Digit
Planet Code Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of Planet Code data. Default = Don’t Transmit. Transmit Check Digit * Don’t Transmit Check Digit Postnet Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of Postnet data.
Page 250: Postal Codes - Linear
Numeric N Table Alphanumeric C Table Combination C and N Tables Postal Codes - Linear The following lists linear postal codes. Any combination of linear postal code selec- tions can be active at a time. China Post (Hong Kong 2 of 5) <Default All China Post (Hong Kong 2 of 5) Settings>...
Page 251: Korea Post
Maximum Message Length Korea Post <Default All Korea Post Settings> Korea Post * Off Korea Post Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 178) for additional information. Minimum and Maximum lengths = 2-80.
Page 252 * Don’t Transmit Check Digit Xenon/Granit User Guide...
Page 253: Chapter 10 - Imaging Commands
CHAPTER IMAGING COMMANDS The scanner is like a digital camera in the way it captures, manipulates, and trans- fers images. The following commands allow you to alter the way the scanner per- forms these functions. Note: If you are using the scanner in a stand, you must set the In-Stand Sensor Mode to Off in order to take images (see In-Stand Sensor Mode on page 122).
Page 254: Image Snap - Imgsnp
Image Ship - IMGSHP (page 237) Intelligent Signature Capture - IMGBOX (page 247) The modifiers for each of these commands follow the command description. Note: The images included with each command description are examples only. The results you achieve may be different from those included in this manual. The quality of the output you receive will vary depending on lighting, quality of the initial image/object being captured, and distance of the scanner from the image/object.
Page 255 B - Beeper Causes a beep to sound after an image is snapped. No beep (default) Sounds a beep when the image is captured. T - Wait for Trigger Waits for a hardware trigger press before taking the image. This is only available when using Photo Style (1P).
Page 256 G - Gain Gain is used in Manual Style only (2P). Like a volume control, the gain modifier boosts the signal and multiplies the pixel value. As you increase the gain, the noise in an image is also amplified. No gain (default) Medium gain Heavy gain Maximum gain...
Page 257: Image Ship - Imgshp
U - Update Tries This sets the maximum number of frames the scanner should take to reach the Delta for Acceptance. Update Tries is only available when using Photo Style (1P). (Default = 6) Range: 0 - 10 % - Target Set Point Percentage Sets the target point for the light and dark values in the captured image.
Page 258: Imgshp Modifiers
IMGSHP Modifiers A - Infinity Filter Enhances pictures taken from very long distances (greater than 10 feet or 3m). The Infinity Filter should not be used with IMGSNP Modifiers (page 234). Infinity filter off (default) Infinity filter on Example: Infinity Filter off (0A) nfinity Filter on (1A) from approximately 12 feet from approximately 12 feet (3.66m)
Page 259 E - Edge Sharpen An edge sharpen filter cleans up the edges of an image, making it look cleaner and sharper. While edge sharpening does make the image look cleaner, it also removes some fine detail from the original image. The strength of the edge sharpen filter can be entered from 1 to 24.
Page 260 F - File Format Indicates the desired format for the image. KIM format TIFF binary TIFF binary group 4, compressed TIFF grayscale Uncompressed binary (upper left to lower right, 1 pixel/bit, 0 padded end of line) Uncompressed grayscale (upper left to lower right, bitmap format) JPEG image (default) BMP format (lower right to upper left, uncompressed) TIFF color compressed image...
Page 261 I - Invert Image Invert image is used to rotate the image around the X or Y axis. Invert around the X axis (flips picture upside down) Invert around the Y axis (flips picture left to right) Example: Image not inverted: Image with Invert Image with Invert Image set to 1ix:...
Page 262 IR - Image Rotate Image as snapped (rightside up) (default) Rotate image 90 degrees to the right Rotate image 180 degrees (upside down) Rotate image 90 degrees to the left Example: Image Rotate set to 2ir: Image Rotate set to 0ir: Image Rotate set to 1ir: Image Rotate set to 3ir: J - JPEG Image Quality...
Page 263 K - Gamma Correction Gamma measures the brightness of midtone values produced by the image. You can brighten or darken an image using gamma correction. A higher gamma correc- tion yields an overall brighter image. The lower the setting, the darker the image. The optimal setting for text images is 50K.
Page 264 The bottom edge of the shipped image corresponds to row n - 1 of the image in memory. Range: 000 - 639. (Default = all rows) Example: Uncropped Image: Image Crop set to Image Crop set to 300R: 300L: Image Crop set to 200B: Image Crop set to 200T: Alternately, specify the number of pixels to cut from the outside margin of the image;...
Page 265 The smaller number of pixels shipped, the smaller the image, however, after a cer- tain point the image becomes unusable. ship every pixel (default) ship every 2nd pixel, both horizontally and vertically ship every 3rd pixel, both horizontally and vertically Pixel Ship Pixel Ship Pixel Ship set to 1S:...
Page 266: Image Size Compatibility
V - Blur Image Smooths transitions by averaging the pixels next to the hard edges of defined lines and shaded areas in an image. Don’t blur (default) Blur Example: Blur Image Off (0V): Blur Image On (1V): W - Histogram Ship A histogram gives a quick picture of the tonal range of an image, or key type.
Page 267: Intelligent Signature Capture - Imgbox
* Native Resolution Intelligent Signature Capture - IMGBOX IMGBOX allows you to configure the size and location of a signature capture area relative to its proximity to a bar code. This allows you to tailor a signature capture area to a specific form. In order to use IMGBOX, you need a set form where the sig- nature box location is in a known location relative to a bar code.
Page 268: Imgbox Modifiers
To see this example, align the aimer with the signature area (not with the bar code), then press the trigger. Send the following IMGBOX command string after the trigger press: Example: IMGBOX245w37h55y. Note: Case is not important in the command string. It is used here only for clarity. The following image is captured: The IMGBOX commands have many different modifiers that can be used to change the size and appearance of the signature image output by the scanner.
Page 269 B - Output Image Height This option is used to size the image vertically. If using this option, set the resolu- tion (R) to zero. Example: Image Height set to 50B: Image Height set to 100B: D - Pixel Depth This indicates the number of bits per pixel in the transmitted image, which defines whether it will be grayscale or black and white.
Page 270 H - Height of Signature Capture Area The height of the signature capture area must be measured in inches divided by .01. In the example, the height of the area to be captured is 3/8 inch, resulting in a value of H = .375/0.01 = 37.5. Example: IMGBOX245w37h55y.
Page 271 decimal point between the first and second digit. For example, use 2500 to specify a resolution of 2.5. Set to zero when using the A and B modifiers (see A - Output Image Width B - Output Image Height on page 249). Example: Resolution set to 0R: Resolution set to 1000R:...
Page 272: Rf Default Imaging Device
Y - Vertical Bar Code Offset The vertical bar code offset allows you to offset the vertical center of the signature capture area. Negative numbers indicate that the signature capture is above the bar code, and positive numbers indicate that the area is below the bar code. Mea- surements are in multiples of the minimum bar width Example: Vertical Offset set to -7Y:...
Page 273: Chapter 11 - Utilities
CHAPTER UTILITIES To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts, beginning on page 327) for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D.
Page 274: Show Software Revision
Show Software Revision Scan the bar code below to output the current software revision, unit serial number, and other product information for both the scanner and base. Show Software Revision Show Data Format Scan the bar code below to show current data format settings. DFMBK3?.
Page 275: Application Plug-Ins (Apps)
Application Plug-Ins (Apps) Any apps that you are using can be turned off or on by scanning the following bar codes. Apps are stored in groups: Decoding, and Formatting. You can enable and disable these groups of apps by scanning that group’s On or Off bar code below. You can also scan the List Apps bar code to output a list of all your apps.
Page 276: Ezconfig Cloud For Scanning Operations
Imaging also lets you preview the images continuously captured by the scanner. Install EZConfig Cloud for Scanning Use the EZConfig Cloud for Scanning tool to configure your scanner online: 1. Access the Honeywell web site at www.honeywellaidc.com 2. Click on the Browse Products tab. Under Software, select Device Management.
Page 277: Reset The Factory Defaults
Reset the Factory Defaults Caution: This selection erases all your settings and resets the scanner to the original factory defaults. It also disables all plugins. If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want to restore the scanner to factory default settings, first scan the Remove Custom Defaults bar code, then scan Activate Defaults.
Page 278 Xenon/Granit User Guide...
Page 279: Chapter 12 - Serial Programming Commands
CHAPTER SERIAL PROGRAMMING COMMANDS The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will program the scanner. For complete descriptions and examples of each serial programming command, refer to the corresponding programming bar code in this manual.
Page 280: Query Commands
scanner. This setting is changed by using the BT_NAM command, which accepts alphanumeric values. If the name is not known, a wildcard (*) can be used :* Note: Since the base stores all work group settings and transfers to them to scanner once they are linked, changes are typically done to the base and not to the scanner.
Page 281: Concatenation Of Multiple Commands
SubTag Field Usage When a query is used in place of a SubTag field, the query applies only to the sub- set of commands available that match the Tag field. In this case, the Data field should not be used because it is ignored by the device. Data Field Usage When a query is used in place of the Data field, the query applies only to the spe- cific command identified by the Tag and SubTag fields.
Page 282: Trigger Commands
This response indicates that Codabar Coding Enable (CBRENA) has a range of val- ues from 0 to 1 (off and on). Example: What is the default value for Codabar Coding Enable? Enter: cbrena^. Response: CBRENA1[ACK] This response indicates that the default setting for Codabar Coding Enable (CBRENA) is 1, or on.
Page 283: Reset The Custom Defaults
The scanner scans until a bar code has been read, until the deactivate command is sent, or until the serial time-out has been reached (see Read Time-Out on page 119 for a description, and the serial command on page 276). Reset the Custom Defaults If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults bar code below.
Page 284: Menu Commands
Menu Commands Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Product Default Settings Set Custom Defaults Set Custom Defaults MNUCDP Save Custom Defaults MNUCDS Reset the Custom Defaults Activate Custom Defaults DEFALT Reset the Factory Defaults - Factory Default Settings: PAPDFT&...
Page 285 # Indicates a numeric Page * Indicates default entry Plug and Play Codes Verifone Ruby Terminal PAPRBY Gilbarco Terminal PAPGLB Honeywell Bioptic Aux Port PAPBIO Datalogic Magellan Aux Port PAPMAG NCR Bioptic Aux Port PAPNCR Wincor Nixdorf Terminal PAPWNX Wincor Nixdorf Beetle...
Page 286 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Greek KBDCTY17 Greek (220 Latin) KBDCTY64 Greek (220) KBDCTY61 Greek (319 Latin) KBDCTY65 Greek (319) KBDCTY62 Greek (Latin) KBDCTY63 Greek (MS) KBDCTY66 Greek (Polytonic) KBDCTY60 Hebrew KBDCTY12 Hungarian (101 key) KBDCTY50 Hungary...
Page 287 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Serbia (Latin) KBDCTY36 Slovakia KBDCTY22 Slovakia (QWERTY) KBDCTY49 Slovakia (QWERTZ) KBDCTY48 Slovenia KBDCTY31 Spain KBDCTY10 Spanish variation KBDCTY51 Sweden KBDCTY23 Switzerland (French) KBDCTY29 Switzerland (German) KBDCTY6 Tatar KBDCTY85 Turkey F KBDCTY27...
Page 288 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Keyboard Modifiers *Control + X Off KBDCAS0 DOS Mode Control + X KBDCAS1 Windows Mode Control + X KBDCAS2 Windows Mode Prefix/Suffix Off KBDCAS3 *Turbo Mode Off KBDTMD0 Turbo Mode On KBDTMD1...
Page 289 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry RS232 Handshaking *RTS/CTS Off 232CTS0 Flow Control, No Timeout 232CTS1 Two-Direction Flow Control 232CTS2 Flow Control with Timeout 232CTS3 RS232 Timeout 232DEL#### *XON/XOFF Off 232XON0 XON/XOFF On 232XON1 *ACK/NAK Off 232ACK0...
Page 290 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Beeper Pitch - Base Error *Razz (250) (min 200Hz) BASFQ2250 Medium (3250) BASFQ23250 High (4200) (max 9000Hz) BASFQ24200 Number of Beeps - Base Error BASERR3 Range 1 - 9 BASERR# Scanner Report Scanner Report...
Page 291 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Batch Mode Quantity *Off BATQTY0 BATQTY1 Quantity Codes BATNUM0 BATNUM1 BATNUM2 BATNUM3 BATNUM4 BATNUM5 BATNUM6 BATNUM7 BATNUM8 BATNUM9 Batch Mode Output Order *FIFO BATLIF0 LIFO BATLIF1 Total Records Total Records BATNRC Delete Last Code...
Page 292 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Bluetooth HID Keyboard PAPSPP Disconnect Bluetooth Serial Port - PCs/ BT_TRM0;BT_DNG5 Laptops BT Connection - PDA/Mobility BT_TRM0;BT_DNG1 Systems Device Bluetooth PIN Code BT_PIN Auto Reconnect Mode *Auto Reconnect On BT_ACM1 Auto Reconnect Off BT_ACM0...
Page 293 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Scan While in Base Cradle Scan in Cradle Off BT_SIC0 *Scan in Cradle On BT_SIC1 Shut Down Scanner in Cradle BT_SIC2 Base Charge Modes Base Charge Off BASCHG0 *External or Interface Cable Power BASCHG1...
Page 294 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Scanner Power Time-Out Timer Timer (0-7200 seconds) BT_LPT0 200 Seconds BT_LPT200 *400 Seconds BT_LPT400 900 Seconds BT_LPT900 3600 Seconds BT_LPT3600 7200 Seconds BT_LPT7200 Flexible Power Management Full Power BT_TXP8 *Medium High Power BT_TXP7...
Page 295 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Batch Mode Transmit Delay *Off BATDLY0 Short (ms) BATDLY250 Medium (ms) BATDLY500 Long (ms) BATDLY1000 Scanner Name Name 1-7 BT_NAM##### Reset RESET_ Scanner Name BT_NAM Bluetooth Connection Bluetooth PIN Code BT_PIN Auto Reconnect Mode...
Page 296 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Vibrate Duration Duration TFBDUR#### (100 - 2,000 ms) *300 Beeper Pitch - Error (Frequency) *Razz (250) (min 200Hz) BEPFQ2800 Medium (3250) BEPFQ23250 High (4200) (max 9000Hz) BEPFQ24200 Beeper Duration - Good Read *Normal Beep BEPBIP0...
Page 297 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Presentation Sensitivity (not Range 0-20 (*1) TRGPMS## supported by Granit 1980i and 1981i) Presentation Centering Window Presentation Centering On PDCWIN1 *Presentation Centering Off PDCWIN0 Left of Presentation Centering PDCLFT### Window (*40%) Right of Presentation Centering...
Page 298 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Character Activation Mode *Off HSTCEN0 HSTCEN1 Activation Character (Range 0- HSTACH### 255) *12 [DC2] Do Not End Character Activation HSTCGD0 After Good Read End Character Activation After HSTCGD1 Good Read Character Activation Timeout...
Page 299 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Partial Sequence Transmit Partial Sequence SEQTTS1 *Discard Partial Sequence SEQTTS0 Require Output Sequence Required SEQ_EN2 On/Not Required SEQ_EN1 *Off SEQ_EN0 Multiple Symbols SHOTGN1 *Off SHOTGN0 No Read SHWNRD1 *Off SHWNRD0...
Page 300 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Low Beeper (Daytime Mode) - beplfn0;beplfr10;beppwr1;beplv Corded Scanner l1;bepbip0;bepFQ12700;beplot Quiet Operations - LED and Volume Settings Linking LED Colors and *Green LED Flashes/Sound BEPPAR1 Sound Red LED Flashes/Silent BEPPAR0 Number of LED Flashes *1 LED Flash...
Page 301 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Suffix Add Suffix SUFBK2## Clear One Suffix SUFCL2 Clear All Suffixes SUFCA2 Function Code Transmit *Enable RMVFNC0 Disable RMVFNC1 Intercharacter Delay Range 0 - 1000 (5ms increments) DLYCHR## User Specified Delay Length...
Page 302 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Symbologies All Symbologies All Symbologies Off ALLENA0 All Symbologies On ALLENA1 Codabar Default All Codabar CBRDFT Settings CBRENA0 CBRENA1 Codabar Start/Stop Char. *Don’t Transmit CBRSSX0 Transmit CBRSSX1 Codabar Check Char.
Page 303 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Interleaved 2 of 5 Default All Interleaved I25DFT 2 of 5 Settings I25ENA0 I25ENA1 Interleaved 2 of 5 Check Digit *No Check Char. I25CK20 Validate, But Don’t I25CK21 Transmit Validate, and Transmit...
Page 304 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Straight 2 of 5 IATA Message Minimum (1 - 48) *4 A25MIN## Length Maximum (1 - 48) *48 A25MAX## Matrix 2 of 5 Default All Matrix 2 of 5 X25DFT Settings *Off...
Page 305 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Telepen Message Length Minimum (1 - 60) *1 TELMIN## Maximum (1 - 60) *60 TELMAX## UPC-A Default All UPADFT UPC-A Settings UPBENA0 UPBENA1 UPC-A Check Digit UPACKX0 UPACKX1 UPC-A Number System UPANSX0...
Page 306 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry UPC-E0 Leading Zero UPENSX0 UPENSX1 UPC-E0 Addenda 2 Digit Addenda On UPEAD21 *2 Digit Addenda Off UPEAD20 5 Digit Addenda On UPEAD51 *5 Digit Addenda Off UPEAD50 UPC-E1 *Off UPEEN10...
Page 307 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry EAN/JAN-8 Addenda Required *Not Required EA8ARQ0 Required EA8ARQ1 Addenda Timeout Range (0 - 120) *500 DLYADD##### EAN/JAN-8 Addenda EA8ADS0 Separator EA8ADS1 Default All MSI Settings MSIDFT *Off MSIENA0 MSIENA1 MSI Check Character...
Page 308 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Codablock A Default All Codablock A Settings CBADFT *Off CBAENA0 CBAENA1 Codablock A Msg. Length Minimum (1 - 600) *1 CBAMIN### Maximum (1 - 600) *600 CBAMAX### Codablock F Default All Codablock F Settings CBFDFT...
Page 309 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry QR Code Default All QR Code Settings QRCDFT QRCENA1 QRCENA0 QR Code Msg. Length Minimum (1-7089) *1 QRCMIN#### Maximum (1-7089) *7089 QRCMAX#### QR Code Append QRCAPP1 QRCAPP0 QR Code Page QR Code Page (*3) QRCDCP##...
Page 310 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Single 2D Postal Codes Australian Post On POSTAL1 British Post On POSTAL7 Canadian Post On POSTAL30 Intelligent Mail Bar Code On POSTAL10 Japanese Post On POSTAL3 KIX Post On POSTAL4 Planet Code On POSTAL5...
Page 311 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Planet, Postal-4i, Intelligent Mail POSTAL28 Bar Code, and Postnet On Planet, Postal-4i, Intelligent Mail POSTAL29 Bar Code, and Postnet with B and B’ Fields On Planet Code Check Digit Transmit PLNCKX1 *Don’t Transmit...
Page 312 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry *Gain - None SNPGAN1 Gain - Medium SNPGAN2 Gain - Heavy SNPGAN4 Gain - Maximum SNPGAN8 Target White Value (0-255) *125 SNPWHT### Delta for Acceptance (0-255) *25 SNPDEL### Update Tries (0-10) *6 SNPTRY##...
Page 313 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry JPEG Image Quality (0-100) *50 IMGJQF### *Gamma Correction Off IMGGAM0 Gamma Correction On (0-1000) IMGGAM### Image Crop - Left (0-843) *0 IMGWNL### Image Crop - Right (0-843) *843 IMGWNR### Image Crop - Top (0-639) *0 IMGWNT###...
Page 314 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Reset the Factory Defaults Remove Custom Defaults DEFOVR Activate Defaults DEFALT Xenon/Granit User Guide...
Page 315: Chapter 13 - Product Specifications
CHAPTER PRODUCT SPECIFICATIONS Xenon 1900/1900h/1910 Corded Scanner Product Specifications Parameter Specification Mechanical Height 6.3 inches (160mm) Length 4.1 inches (104.1mm) Width 2.8 inches (71.1mm) Weight 5.2 ounces (147.42g) Electrical Voltage Requirements 4 - 5.5 VDC at input connector Current Draw @5VDC ScanningStandby B&W...
Page 316: Xenon 1902/1902H/1912 Cordless Scanner Product Specifications
Parameter (Continued) Specification Storage -40F to +158F (-40C to 70C) Humidity 0 to 95% non-condensing Mechanical Drop Operational after 50 drops from 6 feet (1.83m) to concrete at 23°C Vibration Withstands 5G peak from 22 to 300 Hz ESD Tolerance Up to 15kV direct air Up to 8 kV indirect coupling plane Image...
Page 317 Parameter (Continued) Specification Number of Scans Up to 50,000 per charge Expected Hours of Operation Expected Charge Time 4.5 hours Radio Frequency 2.4 to 2.5 GHz (ISM Band) Frequency Hopping Bluetooth v.2.1 Range 33 ft. (10 m) typical Data Rate Up to 1 MBps Environmental Temperature Ranges:...
Page 318: Xenon 1902G-Bf Scanner Product Specifications
Xenon 1902g-BF Scanner Product Specifications Parameter Specification Mechanical Height 6.3 inches (160mm) Length 4.1 inches (104.1mm) Width 2.8 inches (71.1mm) Weight 6.9 ounces (195g) Electrical Illumination LED: Peak Wavelength 624nm + 18nm (red LED) IEC 62471: “Exempt Risk Group” 442nm, 552nm (white LED) IEC 62471: “Exempt Risk Group”...
Page 319: Granit 1910I Industrial Corded Scanner Product Specifications
Parameter (Continued) Specification Motion Tolerance: Up to 240 inches per second for 13 mil UPC Symbol Contrast Grade 1.0 (20% or greater) Granit 1910i Industrial Corded Scanner Product Specifications Parameter Specification Mechanical Height 7.7 in. (195.6mm) Length 5.2 in. (132.1mm) Width 2.9 in.
Page 320: Granit 1911I Industrial Cordless Scanner Product Specifications
Parameter (Continued) Specification Skew Angle +65° Pitch Angle +45° Motion Tolerance: Streaming Presentation Trigger: 240 inches per second at 6.5 in. (16.5cm) 13 mil UPC 150 inches per second at 10 in. (25.4cm) Symbol Contrast Grade 1.0 (20% or greater) Granit 1911i Industrial Cordless Scanner Product Specifications Parameter...
Page 321: Granit 1980I Industrial Full Range Corded Scanner Product Specifications
Parameter (Continued) Specification Temperature Ranges: Operating while not charging -4F to + 122F (-20C to 50C) Operating while charging 41F to + 104F (5C to 40C) Storage with battery* -4F to +95F (-20C to 35C) for storage up to 90 days -4F to +68F (-20C to 20C) for storage up to 365 days...
Page 322: Granit 1981I Industrial Full Range Cordless Scanner Product Specifications
Parameter (Continued) Specification Current Draw @5VDC ScanningStandby 470mA, 2.35W100mA, 0.5W Power Supply Noise Rejection Maximum 100mV peak to peak, 10 to 100 kHz Illumination LED: Peak Wavelength 617nm + 18nm (amber LED) IEC 62471: “Exempt Risk Group” Aiming: Peak Wavelength Laser 650nm IEC 60825-1: “Class 2”...
Page 323 Parameter (Continued) Specification Weight 14.8 oz. (420g) Electrical Illumination LED: Peak Wavelength 617nm + 18nm (amber LED) IEC 62471: “Exempt Risk Group” Aiming: Peak Wavelength Laser 650nm IEC 60825-1: “Class 2” Optical Power Laser <1mW Battery Battery: Lithium Ion 1800 mAHr minimum Number of Scans at least 7200 scans (1 scan every 4 seconds for 8 hours)
Page 324: Granit 1981I Industrial Full Range Cordless Scanner Product Specifications 302 Ccb01-010Bt Charge Base Product Specifications
Parameter (Continued) Specification Pitch Angle +70° typical, 200 lux, EAN/UPC Motion Tolerance: 30 inches per second typical on 13 mil UPC/EAN bar code 8 in. from scanner nose Symbol Contrast 1D codes 30% or greater (typical, 200 lux, 13 mil) 2D codes 40% or greater (typical, 200 lux, 20 mil) *Storage outside of this temperature range could be detrimental to battery life.
Page 325: Ccb01-010Bt-Bf Charge Base Product Specifications
CCB01-010BT-BF Charge Base Product Specifications Parameter Specification Mechanical Height 3.2 inches (81.3mm) Length 5.19 inches (131.8mm) Width 3.98 inches (101.1mm) Weight 6.3 oz (179g) Electrical Voltage: 4.5 to 5.5 volts Current Draw: Host Terminal Port 500mA Aux Power Port Charge Time From shut down to fully charged: 3 minutes via standard USB only 1 minute via powered USB with external power...
Page 326: Ccb02-100Bt/Ccb05-100Bt Industrial Charge Base Product Specifications305 Depth Of Field Charts
Parameter (Continued) Specification Length 9.8 in. (248.9mm) Width 4.05 in. (102.9cm) Weight 10.05 oz. (285g) Electrical Voltage: 4.5 to 5.5 volts Current Draw: Host Terminal Port 500mA Aux Power Port Charge Time 5 hours Radio Frequency 2.4 to 2.5 GHz (ISM Band) Frequency Hopping Bluetooth v.2.1 Range 330 ft.
Page 327: Xenon B&W Scanner Guaranteed Performance
Focus (Continued) High Density (HD) Standard Range (SR) Extended Range (ER) Near Near Near Symbology (Continued) Distance Distance Distance Distance Distance Distance 20 mil Code 39 24.6 23.5 15.2 218.4 10.2 624.8 25.4 596.9 6.7 mil PDF417 10.2 101.6 17.8 152.4 71.1 233.7...
Page 328: Xenon Color Scanner (Model Col) Typical Performance
Xenon Color Scanner (Model COL) Typical Performance Focus High Density (HD) Standard Range (SR) Near Symbology Far Distance Near Distance Far Distance Distance 5 mil Code 39 91.4 27.9 132.1 13 mil UPC 16.2 10.2 149.9 10.2 411.5 20 mil Code 39 10.2 213.4 12.7...
Page 329: Granit 1910I/1911I Scanner Typical Performance
Granit 1910i/1911i Scanner Typical Performance Focus Extended Range (ER) Symbology Near Distance Far Distance 5 mil Code 39 91.4 20 mil Code 39 29.5 15.2 749.3 100% UPC 21.4 15.2 543.6 6.7 mil PDF417 68.6 226.1 10 mil Data Matrix 10.3 71.1 261.6...
Page 330: Granit 1980I/1981I Scanner Typical Performance (200 Lux)
Granit 1980i/1981i Scanner Typical Performance (200 lux) Focus Full Range (FR) Symbology Near Distance Far Distance 7.5 mil Code 39 64.9 10.0 164.9 10 mil Code 39 85.0 10.0 216.0 20 mil Code 39 171.1 15.2 434.5 40 mil Code 39 14.3 389.4 36.4...
Page 331: Standard Connector Pinouts
2 mil (.051mm) Standard Connector Pinouts Note: The following pin assignments are not compatible with Honeywell legacy products. Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty.
Page 332: Keyboard Wedge
Keyboard Wedge 10 Pin RJ41 Modular Plug - connects to the base Cable shield Cable select Supply ground Terminal data Terminal clock Keyboard clock +5V power Keyboard data Serial Output 10 Pin RJ41 Modular Plug - connects to the base Cable shield Cable select Supply ground...
Page 333: Usb
Cable shield Cable select Supply ground Transmit data Receive data - serial data to scanner +5V power Transmit Enable 10 Pin Modular Plug - connects to the base Cable shield Cable select Supply ground +5V power Data + 10 Data - Xenon/Granit User Guide...
Page 334: Required Safety Labels
Required Safety Labels Xenon 1900/1910/1902/1912 Scanner LASER LIGHT- DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT. RAYONNEMENT LASER NE PAS REGARDER DANS LE FAISCEAU. APPAREIL À LASER DE CLASSE 2. MAX. 1mW: 630-680 nm IEC 60825-1:2007. Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No.
Page 335: Ccb01-010Bt/Ccb01-010Bt-Bf Base
CCB01-010BT/CCB01-010BT-BF Base Part Number, Serial Number and Compliance Label Revision locations Information location Xenon/Granit User Guide...
Page 336: Granit 1910I/1911I/1980I/1981I Scanner
Granit 1910i/1911i/1980i/1981i Scanner LASER LIGHT- DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT. RAYONNEMENT LASER NE PAS REGARDER DANS LE FAISCEAU. APPAREIL À LASER DE CLASSE 2. MAX. 1mW: 630-680 nm IEC 60825-1:2007. Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No.
Page 337: Ccb02-100Bt/Ccb05-100Bt Base
CCB02-100BT/CCB05-100BT Base Compliance Label locations Xenon/Granit User Guide...
Page 338 Xenon/Granit User Guide...
Page 339: Chapter 14 - Maintenance And Troubleshooting
CHAPTER MAINTENANCE AND TROUBLESHOOTING Repairs Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized service center (see Customer Support page xvii). Maintenance Your device provides reliable and efficient operation with a minimum of care. Although specific maintenance is not required, the following periodic checks ensure dependable operation: Cleaning the Scanner...
Page 340: Health Care Housing
When properly seated, the connector is held in the scanner’s handle by a flexible retention tab. The interface cable is designed to be field replaceable. • Order replacement cables from Honeywell or from an authorized distributor. • When ordering a replacement cable, specify the cable part number of the original interface cable.
Page 341: Replacing A Xenon Interface Cable
Replacing a Xenon Interface Cable 1. Turn the power to the host system OFF. 2. Disconnect the scanner’s cable from the terminal or computer. 3. Locate the small hole on the back of the scanner’s handle. This is the cable release. 4.
Page 342: Changing A Xenon Scanner Battery
3. Turn the base upside down. 4. Pull the connector out while maintaining pressure on the connector release clip. CCB02-100BT/CCB05-100BT Base: CCB01-010BT Base: 5. Replace with the new cable. Insert the connector into the opening and press firmly. The connector is keyed to go in only one way, and will click into place.
Page 343: Changing A Granit Scanner Battery
Changing a Granit Scanner Battery 1. Twist the tab in the bottom of the end cap and open the hinged battery door. (When new, the battery door may stick. Use pliers to twist the tab and open the door until it loosens up.) 2.
Page 344: Troubleshooting A Cordless System
The bar code is displayed on the host device correctly, but you still have to press a key to enter it (the Enter/Return key or the Tab key, for example). • You need to program a suffix. Programming a suffix enables the scanner to output the bar code data plus the key you need (such as “CR”) to enter the data into your application.
Page 345: Troubleshooting A Cordless Scanner
Troubleshooting a Cordless Scanner Note: Make sure that your scanner’s battery is charged. Visit the Services and Support section of our website (www.honeywellaidc.com) to check for the latest software for both the scanner and the base or Access Point. Is the scanner having trouble reading your symbols? If the scanner isn’t reading symbols well, check that the symbols: •...
Page 346 Xenon/Granit User Guide...
Page 347: Chapter A - Reference Charts
Refer to Data Edit beginning on page 151 and Data Format beginning on page 157 for information about using Code ID and AIM ID. Linear Symbologies Honeywell Possible modifiers Symbology All Symbologies Codabar Code 11 Code 128 0, 1, 2, 4 Code 32 Pharmaceutical (PARAF) <...
Page 348: Symbologies
0, 1, 2, 3, 8, 9, A, B, C UPC-A UPC-A with Add-On UPC-A with Extended Coupon Code UPC-E UPC-E with Add-On UPC-E1 Add Honeywell Code ID 5C80 Add AIM Code ID 5C81 Add Backslash 5C5C Batch mode quantity 2D Symbologies...
Page 349: Postal Symbologies
Honeywell Possible modifiers Symbology Chinese Sensible Code (Han Xin Code) Codablock A 0, 1, 4, 5, 6 Codablock F 0, 1, 4, 5, 6 Code 49 0, 1, 2, 4 Data Matrix GS1 Composite GS1 DataBar Omnidirectional MaxiCode PDF417 MicroPDF417...
Page 350: Ascii Conversion Chart (Code
ASCII Conversion Chart (Code Page 1252) In keyboard applications, ASCII Control Characters can be represented in 3 differ- ent ways, as shown below. The CTRL+X function is OS and application dependent. The following table lists some commonly used Microsoft functionality. This table applies to U.S.
Page 351: Lower Ascii Reference Table
Lower ASCII Reference Table Note: Windows Code page 1252 and lower ASCII use the same characters. Printable Characters Character Character DEC Character <SPACE> " & < > ⌂ Extended ASCII Characters CP 1252 ASCII Alternate Extended PS2 Scan Code ↑ €...
Page 352 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code Œ î Reserved ì Reserved Ž Ä Numeric Keypad Enter 0x1C Å Numeric Keypad / 0x35 É 0x3B ‘ æ 0x3C ’ Æ 0x3D “ ô 0x3E ” ö...
Page 353 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code Â ┬ Ã ├ Ä ─ Å í Æ ╞ Ç ╟ È ╚ É ╔ Ê ╩ Ë ╦ Ì ╠ Í ═ Î ╬ Ï ╧ Ð...
Page 354: Iso 2022/Iso 646 Character Replacements
(standard ASCII) Automatic National Character ISO/IEC 2022 2 (default) Replacement Binary Code page Default “Automatic National Character replacement” will select the below Honeywell Code Page options for Code128, Code 39 and Code 93. United States ISO/IEC 646-06 Canada ISO /IEC 646-121...
Page 355 Honeywell Code Page Selection Method/ Keyboard Code Standard Country Country Page Option Spain ISO/IEC 646-17 Spain ISO/IEC 646-85 Xenon/Granit User Guide...
Page 356 à â ç ê î ô é ù è û à â ç ê É ô é ù è û ⎯ ¥ ⎯ ¥ £ ˜ £ à ° ç § µ é ù è ¨ § Ä Ö Ü ä...
Page 357: Keyboard Key References
Keyboard Key References 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 4B 50 55 5A 5F 64 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 4C 51 56 5B 60 65 1F 20 21 22 23 24 25 26 27 28 29...
Page 358 Xenon/Granit User Guide...
Page 359: Sample Symbols
Sample Symbols UPC-A Interleaved 2 of 5 01234567890 0 123456 7890 EAN-13 9 780330 290951 Code 128 Code 39 Code 128 BC321 Codabar A13579B Code 93 Straight 2 of 5 Industrial 123456 123456-9$ Matrix 2 of 5 6543210 RSS-14 PDF417 Car Registration (01) 00123456789012 Code 49...
Page 360 Sample Symbols (Continued) Postnet Data Matrix Zip Code Test Symbol QR Code Numbers MaxiCode Micro PDF417 Test Message Test Message Xenon/Granit User Guide...
Page 361: Programming Chart
Programming Chart Xenon/Granit User Guide...
Page 362 Programming Chart (Continued) Save Discard Reset Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again. Xenon/Granit User Guide...
Page 364 Honeywell 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com ™ Xenon-UG Rev R 2/17...

This manual is also suitable for:

Xenon 1902h Xenon 1912 Xenon 1900h Xenon 1902g-bf Granit 1910i Granit 1911i ... Show all

Honeywell Xenon 1900 User Manual

Chapter 1 - Get Started

Chapter 2 - Program the Interface

Chapter 3 - Cordless System Operation: Xenon 1902G/1912 and Granit 1911I/1981I

Chapter 4 - Cordless System Operation: Xenon 1902G-BF

Chapter 5 - Input/Output Settings

Chapter 6 - Healthcare Settings

Chapter 7 - Data Edit

Quick Links

User Guide

Troubleshooting

Related Manuals for Honeywell Xenon 1900

Summary of Contents for Honeywell Xenon 1900