Page 1 Xenon™ 1900/1902 Area-Imaging Scanner User’s Guide ™...
Page 2 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in speci- fications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not repre- sent a commitment on the part of HII.
Page 3 The user may find the fol- lowing booklet helpful: “Something About Interference.” This is available at FCC local regional offices. Honeywell is not responsible for any radio or television interference caused by unauthorized modifications of this equip- ment or the substitution or attachment of connecting cables and equipment other than those specified by Honeywell.
Page 4 Nijverheidsweg 9-13 5627 BT Eindhoven The Netherlands Honeywell International Inc. shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive.
Page 5 In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems for product disposal. Those sys- tems will reuse or recycle most of the materials of the product you are dis- posing in a sound way.
Page 6 Class 1 LED product. CB Scheme Certified to IEC60950-1 (2001) First Edition. Patents Please refer to the product packaging for patent information. Solids and Water Protection The Xenon 1900 has a rating of IP41, immunity of foreign particles and dripping water.
Page 7 Required Safety Labels Scanner Illumination output Item Compliance Number, Serial Label Number and location Revision Information location...
Page 8 CCB01-010BT Base Item Number, Serial Number and Compliance Revision Label Information location location...
Page 9: Table Of Contents
® Verifone Ruby Terminal Default Settings .... 2-6 ® Gilbarco Terminal Default Settings ..... 2-7 Honeywell Bioptic Aux Port Configuration..... 2-7 © Datalogic™ Magellan Bioptic Aux Port Configuration............ 2-7 NCR Bioptic Aux Port Configuration...... 2-8 Wincor Nixdorf Terminal Default Settings ..... 2-8...
Page 10 Wincor Nixdorf Beetle™ Terminal Default Settings ..........2-9 Keyboard Country Layout ..........2-10 Keyboard Style ............2-17 Keyboard Conversion ..........2-18 Control Character Output...........2-19 Keyboard Modifiers............2-19 RS232 Baud Rate............2-22 RS232 Word Length: Data Bits, Stop Bits, and Parity ..............2-23 RS232 Receiver Time-Out.........2-24 RS232 Handshaking..........2-24 RS232 Timeout ............
Page 11 Proper Disposal of the Battery ......3-5 Beeper and LED Sequences and Meaning ....3-5 Scanner LED Sequences and Meaning ....3-6 Base LED Sequences and Meaning ..... 3-6 Base Power Communication Indicator ....3-7 Reset Scanner ............3-7 Scanning while in Base Cradle ........3-7 Paging .................
Page 12 Application Work Group Selection ....... 3-24 Resetting the Factory Defaults: All Application Work Groups........3-24 Resetting the Custom Defaults: All Application Work Groups........3-25 Using the Scanner with Bluetooth Devices....3-25 PCs/Laptops ............3-25 PDAs/Mobility Systems Devices ......3-26 Changing the Scanner’s Bluetooth PIN Code..3-26 Minimizing Bluetooth/ISM Band Network Activity ..3-26 Auto Reconnect Mode .........
Page 13 Presentation LED Behavior after Decode ..... 4-9 Presentation Sensitivity ........4-10 Streaming Presentation™ Mode ....... 4-10 Mobile Phone Read Mode......... 4-11 Image Snap and Ship..........4-11 Hands Free Time-Out ..........4-11 Reread Delay ............4-12 User-Specified Reread Delay........4-12 Illumination Lights ............. 4-13 Aimer Delay...............
Page 14 To Add a Carriage Return Suffix to All Symbologies..........5-3 Prefix Selections ............5-3 Suffix Selections ............5-4 Function Code Transmit ..........5-4 Intercharacter, Interfunction, and Intermessage Delays..........5-4 Intercharacter Delay ..........5-5 User Specified Intercharacter Delay ...... 5-5 Interfunction Delay ..........5-6 Intermessage Delay ..........5-6 Chapter 6 - Data Formatting Data Format Editor Introduction........6-1 To Add a Data Format ..........6-1...
Page 15 NEC 2 of 5..............7-12 Code 93..............7-14 Code 93 Code Page..........7-14 Straight 2 of 5 Industrial (three-bar start/stop) ..7-15 Straight 2 of 5 IATA (two-bar start/stop)....7-16 Matrix 2 of 5 .............. 7-17 Code 11..............7-18 Code 128..............7-19 ISBT 128 Concatenation ........
Page 16 Chinese Sensible (Han Xin) Code ......7-50 Postal Codes - 2D............7-51 Single 2D Postal Codes: ........7-51 Combination 2D Postal Codes:......7-52 Postal Codes - Linear ..........7-54 China Post (Hong Kong 2 of 5) ......7-54 Korea Post ............7-56 Chapter 8 - Imaging Commands Single-Use Basis ............8-1 Command Syntax ............8-1 Image Snap - IMGSNP ..........8-2...
Page 17 Chapter 11 - Serial Programming Commands Conventions .............. 11-1 Menu Command Syntax..........11-1 Query Commands ............. 11-2 Responses ............11-3 Trigger Commands ........... 11-4 Resetting the Standard Product Defaults ....11-4 Menu Commands ............11-5 Chapter 12 - Product Specifications 1900 Scanner Product Specifications .......
Page 18 Chapter 14 - Customer Support Appendix A - Reference Charts Symbology Chart ............A-1 ASCII Conversion Chart (Code Page 1252) ....A-4 Code Page Mapping of Printed Barcodes ....A-6...
Page 19: Chapter 1 - Getting Started
Xenon™ 1900 and 1902 area-imaging scanners. Product specifications, dimensions, warranty, and customer support information are also included. Honeywell bar code scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide.
Page 20: Connecting The Device
Connecting the Device Connecting with USB A scanner or a cordless base can be connected to the USB port of a com- puter. Connect the appropriate interface cable to the device first, then to the computer. Corded Scanner USB Connection: Cordless Base USB Connection: 1 - 2...
Page 21: Connecting With Keyboard Wedge
Make sure the cables are secured in the wireways in the bottom of the cordless base and that the base sits flat on a horizontal surface. The scanner beeps. Verify the scanner or cordless base operation by scanning a bar code from the Sample Symbols in the back of this manual.
Page 22 Cordless Base Keyboard Wedge Connection: Make sure the cables are secured in the wireways in the bottom of the cordless base and that the base sits flat on a horizontal surface. Turn the terminal/computer power back on. The scanner beeps. Verify the scanner or cordless base operation by scanning a bar code from the Sample Symbols...
Page 23: Connecting With Rs232 Serial Port
Connecting with RS232 Serial Port Turn off power to the terminal/computer. Connect the appropriate interface cable to the scanner. Note: For the scanner or cordless base to work properly, you must have the correct cable for your type of terminal/computer. Corded Scanner RS232 Serial Port Connection:...
Page 24: Connecting With Rs485
Make sure the cables are secured in the wireways in the bottom of the cordless base and that the base sits flat on a horizontal surface. Plug the serial connector into the serial port on your computer. Tighten the two screws to secure the connector to the port. Once the scanner or cordless base has been fully connected, power up the computer.
Page 25 Cordless Base RS485 Connection: Make sure the cables are secured in the wireways in the bottom of the cordless base and that the base sits flat on a horizontal surface. Turn the terminal/computer power back on. The scanner beeps. Verify the scanner or cordless base operation by scanning a bar code from the Sample Symbols in the back of this manual.
Page 26: Reading Techniques
15° to 18° to prevent unwanted reflection. Menu Bar Code Security Settings Honeywell scanners are programmed by scanning menu bar codes or by send- ing serial commands to the scanner. If you want to restrict the ability to scan menu codes, you can use the Menu Bar Code Security settings.
Page 27: Resetting The Factory Defaults
Resetting the Factory Defaults If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want the factory default settings restored, first scan the Restore Factory Defaults bar code, then scan Save Defaults. This resets the scanner to the factory defaults.
Page 28: Resetting The Custom Defaults
When you have entered all the commands you want to save for your custom defaults, scan the Save Custom Defaults bar code. Set Custom Defaults Save Custom Defaults Note: If using a cordless system, scanning the Save Defaults bar code also causes both the scanner and the base to perform a reset and become unlinked.
Page 29: Chapter 2 - Programming The Interface
Programming the Interface Introduction This chapter describes how to program your system for the desired interface. Programming the Interface - Plug and Play Plug and Play bar codes provide instant scanner set up for commonly used interfaces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect.
Page 30: Rs232 Serial Port
RS232 Serial Port The RS232 Interface bar code is used when connecting to the serial port of a PC or terminal. The following RS232 Interface bar code also pro- grams a carriage return (CR) and a line feed (LF) suffix, baud rate, and data format as indicated below.
Page 31: Rs485 Packet Mode
Each bar code above also programs the following suffixes for each symbol- ogy: Symbology Suffix Symbology Suffix EAN 8 Code 39 00 0A 0B EAN 13 Interleaved 2 of 5 00 0D 0B UPC A Code 128 * 00 0A 0B UPC E Code 128 ** 00 18 0B...
Page 32: Usb Ibm Surepos
USB IBM SurePos Scan one of the following “Plug and Play” codes to program the scanner for an IBM SurePos (USB handheld scanner) or IBM SurePos (USB tabletop scanner) interface. Note: After scanning one of these codes, you must power cycle the cash register.
Page 33: Usb Hid
Scan the following code to program the scanner to emulate a regular RS232-based COM Port. If you are using a Microsoft® Windows® PC, you will need to download a driver from the Honeywell website (www.honeywellaidc.com). The driver will use the next available COM Port number.
Page 34: Verifone ® Ruby Terminal Default Settings
ACK/NAK Mode ACK/NAK Mode On * ACK/NAK Mode Off ® Verifone Ruby Terminal Default Settings Scan the following Plug and Play code to program the scanner for a Veri- fone Ruby terminal. This bar code sets the baud rate to 1200 bps and the data format to 8 data bits, no parity bit, 1 stop bit.
Page 35: Gilbarco ® Terminal Default Settings
EAN-8 EAN-13 Gilbarco Settings Honeywell Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for a Honey- well bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit.
Page 36: Ncr Bioptic Aux Port Configuration
NCR Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for an NCR bioptic scanner auxiliary port configuration. The following prefixes are pro- grammed for each symbology: Symbology Prefix Symbology Prefix UPC-A Code 39 UPC-E Interleaved 2 of 5 EAN-8...
Page 37: Wincor Nixdorf Beetle™ Terminal Default Settings
Wincor Nixdorf Beetle™ Terminal Default Settings Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf Beetle terminal. The following prefixes are programmed for each symbology: Symbology Prefix Symbology Prefix Code 128 EAN-13 Code 93 GS1-128 Codabar Interleaved 2 of 5...
Page 38: Keyboard Country Layout
Keyboard Country Layout Scan the appropriate country code below to program the keyboard layout for your country or language. As a general rule, the following characters are sup- ported, but need special care for countries other than the United States: @ | $ # { } [ ] = / ‘...
Page 39 Keyboard Country (continued) Brazil (MS) Bulgaria (Cyrillic) Bulgaria (Latin) Canada (French legacy) Canada (French) Canada (Multilingual) Croatia Czech Czech (Programmers) Czech (QWERTY) Czech (QWERTZ) Denmark Dutch (Netherlands) 2 - 11...
Page 40 Keyboard Country (continued) Estonia Faeroese Finland France Gaelic Germany Greek Greek (220 Latin) Greek (220) Greek (319 Latin) Greek (319) Greek (Latin) Greek (MS) 2 - 12...
Page 41 Keyboard Country (continued) Greek (Polytonic) Hebrew Hungarian (101 key) Hungary Iceland Irish Italian (142) Italy Japan ASCII Kazakh Kyrgyz (Cyrillic) Latin America Latvia 2 - 13...
Page 42 Keyboard Country (continued) Latvia (QWERTY) Lithuania Lithuania (IBM) Macedonia Malta Mongolian (Cyrillic) Norway Poland Polish (214) Polish (Programmers) Portugal Romania Russia 2 - 14...
Page 43 Keyboard Country (continued) Russian (MS) Russian (Typewriter) Serbia (Cyrillic) Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation Sweden Switzerland (French) 2 - 15...
Page 44 United States (Dvorak left) United States (Dvorak) United States (International) Uzbek (Cyrillic) Refer to the Honeywell website (www.honeywell.com/aidc) for complete key- board country support information and applicable interfaces. If you need to pro- gram a keyboard for a country other than one listed above, scan the Program...
Page 45: Keyboard Style
appropriate country from the inside back cover, then the Save bar code. Program Keyboard Country Keyboard Style This programs keyboard styles, such as Caps Lock and Shift Lock. If you have used Keyboard Conversion settings, they will override any of the following Key- board Style settings.
Page 46: Keyboard Conversion
Autocaps via NumLock bar code should be scanned in countries (e.g., Ger- many, France) where the Caps Lock key cannot be used to toggle Caps Lock. The NumLock option works similarly to the regular Autocaps, but uses the Num- Lock key to retrieve the current state of the Caps Lock. Autocaps via NumLock Emulate External Keyboard should be scanned if you do not have an external keyboard (IBM AT or equivalent).
Page 47: Control Character Output
Control Character Output This selection sends a text string instead of a control character. For example, when the control character for a carriage return is expected, the output would display [CR] instead of the ASCII code of 0D. Refer to ASCII Conversion Chart (Code Page 1252) on page A-4.
Page 48 Default = Control + ASCII Mode Off. Windows Mode Control + ASCII Mode On * Control + ASCII Mode Off DOS Mode Control + ASCII Mode Windows Mode Prefix/Suffix Off Turbo Mode: The scanner sends characters to a terminal faster. If the termi- nal drops characters, do not use Turbo Mode.
Page 49 Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters. Default = Off Automatic Direct Connect Mode * Automatic Direct Connect Mode Off 2 - 21...
Page 50: Rs232 Baud Rate
RS232 Baud Rate Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the scanner. Default = 9600. 1200 2400 4800 * 9600 19200 38400 57,600...
Page 51: Rs232 Word Length: Data Bits, Stop Bits, And Parity
RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an applica- tion requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits.
Page 52: Rs232 Receiver Time-Out
RS232 Receiver Time-Out The unit stays awake to receive data until the RS232 Receiver Time-Out expires. A manual or serial trigger resets the time-out. When an RS232 receiver is sleeping, a character may be sent to wake up the receiver and reset the time-out.
Page 53: Rs232 Timeout
RS232 Timeout When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host. Set the length (in millisec- onds) for a timeout by scanning the bar code below, then setting the time- out (from 1-5100 milliseconds) by scanning digits from the inside back cover, then scanning Save.
Page 54: Scanner To Bioptic Communication
ACK/NAK On * ACK/NAK Off Scanner to Bioptic Communication The following settings are used to set up communication between Honeywell scanners and bioptic scanners. Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with a bioptic scanner. See...
Page 55: Scanner-Bioptic Ack/Nak Mode
Scanner-Bioptic ACK/NAK Mode Bioptic ACK/Nak On must be scanned so the scanner will wait for an ACK or NAK from a bioptic scanner after each packet is sent. The Scanner- Bioptic ACK/NAK Timeout (below) controls how long the scanner will wait for a response.
Page 56 2 - 28...
Page 57: Chapter 3 - Cordless System Operation
Cordless System Operation Note: This chapter applies only to cordless scanning systems. It does not apply to corded scanners. How the Cordless Base Works The cordless base provides the link between the cordless scanner and the host system. The base contains an interface assembly and an RF communication module.
Page 58: Communication Between The Cordless System And The Host
Communication Between the Cordless System and the Host The cordless scanner provides immediate feedback in the form of a “good read” indication (a green LED on the scanner and an audible beep) after a bar code is scanned correctly and the base has acknowledged receiving the data. This is possible since the cordless system provides two-way communication between the scanner and the base.
Page 59: Linking Process
Linking Process Once a scanner is placed into the base, the scanner’s battery charge status is checked, and software automatically detects the scanner and links it to the base depending on the selected link mode. Scanner Is Out of Range The cordless scanner is in communication with its base, even when it is not transmitting bar code data.
Page 60: Charging Information
Replace it after the battery is unable to hold an adequate charge. • If you are not sure if the battery or charger is working properly, send it to Honeywell International Inc. or an authorized service center for inspection. Refer to Customer Support on page 14-1 for additional information.
Page 61: Proper Disposal Of The Battery
Proper Disposal of the Battery When the battery has reached the end of its useful life, the battery should be disposed of by a qualified recycler or hazardous materials handler. Do not incinerate the battery or dispose of the battery with general waste materials.
Page 62: Scanner Led Sequences And Meaning
Scanner LED Sequences and Meaning LED Indication Beeper Indication Cause Normal Operation Red Flash None Battery low Green Flash 1 beep Successful communication or linking Red, blinking Razz or error tone Failed communication Menu Operation Green Flash 2 beeps Successful menu change Red, blinking Razz or error tone Unsuccessful menu...
Page 63: Base Power Communication Indicator
Base Power Communication Indicator To display the power indicator on the base, scan the Base Power Commu- nication Indicator On bar code. To turn off the power indicator, scan the Off bar code. Default = On . * Base Power Communication Indicator On Base Power Communication Indicator Off...
Page 64: Paging
Paging Paging Mode By default, the paging button on the base pages the scanners associated with that base. If you want the paging button on your base to be disabled, scan the Paging Mode Off bar code, below. When Paging Mode is off, the base will no longer page scanners when the button is pressed.
Page 65: Error Indicators
Error Indicators Beeper Pitch - Base Error The base can be configured to beep at a particular pitch when an error occurs, such as transmission problems to a host system. The beeper pitch codes modify the pitch (frequency) of the error tone the base emits when there is an error.
Page 66: Scanner Address
Scanner Address Scan the bar code below to determine the address of the scanner you are using. Scanner Address Base Address Scan the bar code below to determine the address of the base you are using. Base Address Scanner Modes The Xenon is capable of working in single scanner mode, multiple scanner mode, or with Bluetooth devices other than the CCB01-010BT charge base.
Page 67: Open Link Mode - Single Scanner
Open Link Mode - Single Scanner When newly shipped or defaulted to factory settings, the base and scanner are not linked. By placing a scanner into the base, they establish a link. Placing a different scanner into the base establishes a new link and the old scanner is unlinked.
Page 68: Alarm Sound Type
alarm duration, scan the appropriate bar code below and then set the time-out duration (from 0-3000 seconds) by scanning digits on the Programming Chart inside the back cover, then scanning Save. Default = 0 sec (no alarm). Base Alarm Duration Scanner Alarm Duration Note: If you are out of range when you scan a bar code, you will receive an error tone even if you do not have the alarm set.
Page 69: Flexible Power Management
Flexible Power Management If you are experiencing network performance issues, and suspect the scanner is interfering with other devices, you can turn down the power output of the scan- ner. This reduces the range between the scanner and the base as shown in the following illustration: 802.11 1902...
Page 70: Batch Mode
Reset Scanner and Base Once the power level is set, you must scan the Reset Base bar code and wait for the scanner to unlink and relink to the base. Once that is done, scan the Reset Scanner bar code and wait for the base to unlink and relink to the scanner.
Page 71: Batch Mode Beep
Default = Batch Mode Off. * Batch Mode Off Automatic Batch Mode Inventory Batch Mode Batch Mode Beep Scan Batch Mode Beep On to program the scanner to beep when it enters Batch Mode. Default = Batch Mode Beep On. Batch Mode Beep Off * Batch Mode Beep On Batch Mode Storage...
Page 72: Batch Mode Quantity
RAM Storage: The scanner will not power down while it contains data that has not been transmitted to the base, even if it reaches a power down time- out. However, if the scanner runs out of battery power, it will power down and the data will be lost.
Page 73 2. Scan the quantity 1 bar code. 3. Scan the quantity 5 bar code. 4. Scan the quantity 0 bar code. 5. Scan the quantity 0 bar code. Example: Change a quantity of 103 to 10. To correct an incorrect quantity, scan the quantity 0 bar code to replace the incorrect digits, then scan the correct quantity bar codes.
Page 74: Batch Mode Output Order
Quantity Codes (continued) Batch Mode Output Order When data is transmitted to the base, select whether you want that data sent as FIFO (first-in first-out), or LIFO (last-in last-out). Batch Mode FIFO Batch Mode LIFO Delete Last Code If you are accumulating data in Batch Mode and want to delete the last bar code scanned, scan Delete Last Code.
Page 75: Transmit Records To Host
Transmit Records to Host If you are operating in Inventory Batch Mode (see Inventory Batch Mode page 3-15), you must scan the following bar code to transmit all the stored data to the host system. Transmit Inventory Records Batch Mode Transmit Delay Sometimes when accumulated scans are sent to the host system, the transmission of those scans is too fast for the application to process.
Page 76: Scanner Name
To put the scanner in multiple scanner mode, scan the bar code below. Once you scan this bar code, the scanner is unlinked from the base and must be placed into the base to re-link. Multiple Scanner Operation Scanner Name You may assign a name to each scanner you are using.
Page 77 To rename scanners with sequential, numeric names, scan the bar codes below. Scan the Reset code after each name change and wait for the scanner to re-link to the base before scanning another bar code to rename the next scanner. 0001 0002 0003...
Page 78: Application Work Groups
If you want to assign an alphabetic name to the scanner, create a Code 128 bar code containing “~BT_NAM name .” followed by a FNC3 character (hexidecimal 83), where name is the new scanner name. Scan the Reset bar code (page 3- or on the Programming Chart...
Page 79: Application Work Group Selection
Application Work Group Selection This programming selection allows you to assign a scanner to a work group by scanning the bar code below. You may then program the settings (e.g., beeper volume, prefix/suffix, data formatter) that your application requires. Default = Group 0. * Group 0 Group 1 Group 2...
Page 80: Resetting The Custom Defaults: All Application Work Groups
The scanner can be used either with the CCB01-010BT charge base or with other Bluetooth devices. Those devices include personal computers, laptops, PDAs, and Honeywell mobility systems devices. PCs/Laptops Scanning the Non-Base BT Connection bar code below allows the scan- ner to be used with other Bluetooth devices (e.g., PC/laptop).
Page 81: Pdas/Mobility Systems Devices
Non-Base BT Connection PDAs/Mobility Systems Devices You may also use the scanner with a PDA or a Honeywell Mobility Systems device. Scan the bar code below and follow the instructions supplied with your Bluetooth device to locate the scanner, and connect with it.
Page 82: Auto Reconnect Mode
Auto Reconnect Mode Auto Reconnect controls whether or not the scanner automatically begins the re-link process when a loss of connection is detected. When the Auto Reconnect On bar code is scanned, the scanner begins the re-link pro- cess immediately, without user intervention. Default = Auto Reconnect On. * Auto Reconnect On Auto Reconnect Off The table below shows the results of the Auto Reconnect On and Off set-...
Page 83: Maximum Link Attempts
Event Auto Reconnect On Auto Reconnect Off Scanner reset due Re-link occurs automatically. to battery change Scanner placed in Re-link to new base occurs automatically. different base unit Maximum Link Attempts The Maximum Link Attempts setting controls the number of times the scan- ner tries to form a connection with a base unit or PC.
Page 84: Bluetooth/Ism Network Activity Examples
Bluetooth/ISM Network Activity Examples Default values When the scanner goes out of range, the scanner repeatedly attempts to connect to base unit. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time. After one hour, the scanner powers off and batch mode data is lost.
Page 85 • The cordless system must be configured for Host Port RS232 (terminal ID = 000) or USB COM Emulation (terminal ID = 130). • RTS/CTS is defaulted off. You must enable it if the host system requires it. • Host ACK must be set to On (page 3-30).
Page 86 Host Acknowledgment On/Off Host ACK On * Host ACK Off Cordless Base Host Escape Commands Command Action <ESC> a Double beeps to indicate a successful menu change was made. <ESC> b Razz or error tone to indicate a menu change was unsuccessful.
Page 87: Chapter 4 - Input/Output Settings
Input/Output Settings Power Up Beeper The scanner can be programmed to beep when it’s powered up. If you are using a cordless system, the base can also be programmed to beep when it is powered up. Scan the Off bar code(s) if you don’t want a power up beep. Default = Power Up Beeper On - Scanner.
Page 88: Trigger Click
Trigger Click To hear an audible click every time the scanner trigger is pressed, scan the Trigger Click On bar code below. Scan the Trigger Click Off code if you don’t wish to hear the click. (This feature has no effect on serial or automatic trigger- ing.) Default = Trigger Click Off.
Page 89: Beeper Volume - Good Read
Beeper Volume – Good Read The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High. Medium * High Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the scan- ner emits on a good read.
Page 90: Beeper Pitch - Error
Beeper Pitch – Error The beeper pitch codes modify the pitch (frequency) of the sound the scan- ner emits when there is a bad read or error. Default = Low. * Razz (250 Hz) Medium (3250 Hz) High (4200 Hz) Beeper Duration –...
Page 91: Number Of Beeps - Good Read
Number of Beeps – Good Read The number of beeps of a good read can be programmed from 1 - 9. The same number of beeps will be applied to the beeper and LED in response to a good read. For example, if you program this option to have five beeps, there will be five beeps and five LED flashes in response to a good read.
Page 92: Good Read Delay
Good Read Delay This sets the minimum amount of time before the scanner can read another bar code. Default = 0 ms (No Delay). * No Delay Short Delay (500 ms) Medium Delay (1,000 ms) Long Delay (1,500 ms) User-Specified Good Read Delay If you want to set your own length for the good read delay, scan the bar code below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the inside back cover, then scanning Save.
Page 93: Serial Trigger
ble scan speed but slightly less range than Normal mode. Enhanced mode is best used when you require a very fast scan speed and don’t require a long working range. * Manual Trigger - Normal Manual Trigger - Enhanced Serial Trigger You can activate the scanner either by pressing the trigger, or using a serial trigger command (see Trigger Commands...
Page 94: In-Stand Sensor Mode
If there are no trigger pulls during the timer interval, the scanner goes into power down mode. Whenever the trigger is enabled, the timer is reset. If the scanner is placed in the charge base cradle and the bat- tery is in the process of being charged, the scanner will not go into power down mode.
Page 95: Presentation Mode
device is programmed for Presentation Mode (page 4-9), it would be in presen- tation mode whenever it is in the stand, and in manual trigger mode whenever it is removed from the stand. Default = Sensor On. * Sensor On Sensor Off Presentation Mode Presentation Mode uses ambient light to detect bar codes.
Page 96: Presentation Sensitivity
Presentation Sensitivity Presentation Sensitivity is a numeric range that increases or decreases the scanner's reaction time to bar code presentation. To set the sensitivity, scan the Sensitivity bar code, then scan the degree of sensitivity (from 0- 20) from the inside back cover, and Save. 0 is the most sensitive setting, and 20 is the least sensitive.
Page 97: Mobile Phone Read Mode
Mobile Phone Read Mode When this mode is selected, your scanner is optimized to read bar codes from mobile phone or other LED displays. However, the speed of scanning printed bar codes may be slightly lower when this mode is enabled. You can enable Mobile Phone Reading for either a hand held device, or for a hands-free (pre- sentation) application.
Page 98: Reread Delay
Scan the Hands Free Time-Out bar code, then scan the time-out duration (from 0-300,000 milliseconds) from the inside back cover, and Save. Default = 5,000 ms. Hands Free Time-Out Reread Delay This sets the time period before the scanner can read the same bar code a sec- ond time.
Page 99: Illumination Lights
Illumination Lights If you want the illumination lights on while reading a bar code, scan the Lights On bar code, below. However, if you want to turn just the lights off, scan the Lights Off bar code. Default = Lights On. Note: This setting does not affect the aimer light.
Page 100: Scanner Time-Out
Scanner Time-Out Note: Scanner Time-Out applies only to corded scanners. It does not apply to cordless systems. Scanner Time-Out powers down the scanner after the unit has been idle for the specified time. To prevent the scanner from powering down, set this time-out to 0.
Page 101 In the example below, the gray area is the full scanner field of view and the white area is the centering window. Bar Code 1 will not be read, while Bar Code 2 will Bar Code 1 Bar Code 2 The default centering window is a 169x128 pixel area in the center of the scan- ner’s field of view.
Page 102: Preferred Symbology
Scan Centering On, then scan one of the following bar codes to change the top, bottom, left, or right of the centering window. Then scan the percent you want to shift the centering window using digits on the inside back cover of this manual.
Page 103: High Priority Symbology
Default = Scan a bar code below to enable or disable Preferred Symbology. Preferred Symbology Off. Preferred Symbology On * Preferred Symbology Off High Priority Symbology To specify the high priority symbology, scan the High Priority Symbology bar code below. On the Symbology Chart on page A-1, find the symbology you want to set as high priority.
Page 104: Preferred Symbology Default
bar code has been encountered. Scan the bar code below, then set the delay (from 1-3,000 milliseconds) by scanning digits from the inside back cover, then scanning Save. Default = 500 ms. Preferred Symbology Time-out Preferred Symbology Default Scan the bar code below to set all Preferred Symbology entries to their default values.
Page 105: To Add An Output Sequence
To Add an Output Sequence 1. Scan the Enter Sequence symbol (see Require Output Sequence, page 4-22). 2. Code I.D. On the Symbology Chart on page A-1, find the symbology to which you want to apply the output sequence format. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart (inside back cover).
Page 106: Output Sequence Example
Output Sequence Example In this example, you are scanning Code 93, Code 128, and Code 39 bar codes, but you want the scanner to output Code 39 1st, Code 128 2nd, and Code 93 3rd, as shown below. Note: Code 93 must be enabled to use this example. A - Code 39 B - Code 128 C - Code 93...
Page 107: Output Sequence Editor
SEQBLKsequence editor start command code identifier for Code 39 0012 A - Code 39 sample length (11) plus CR suffix (1) = 12 start character match for Code 39, 41h = “A” termination string for first code code identifier for Code 128 0013 B - Code 128 sample length (12) plus CR suffix (1) = 13 start character match for Code 128, 42h = “B”...
Page 108: Require Output Sequence
Require Output Sequence When an output sequence is Required, all output data must conform to an edited sequence or the scanner will not transmit the output data to the host device. When it’s On/Not Required, the scanner will attempt to get the output data to conform to an edited sequence but, if it cannot, the scanner transmits all output data to the host device as is.
Page 109: No Read
No Read With No Read turned On, the scanner notifies you if a code cannot be read. If using an EZConfig Tool Scan Data Window (see page 10-3), an “NR” appears when a code cannot be read. If No Read is turned Off, the “NR” will not appear. Default = Off.
Page 110 4 - 24...
Page 111: Chapter 5 - Data Editing
Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string.
Page 112: To Clear One Or All Prefixes Or Suffixes
symbology to which you want to apply the prefix or suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”. Step 3. Scan the 2 hex digits from the Programming Chart inside the back cover of this manual or scan 9, 9 for all symbologies. Step 4.
Page 113: To Add A Carriage Return Suffix To All Symbologies
Step 1. Scan the Clear One Prefix or Clear One Suffix symbol. Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in the Symbology Chart, beginning on page A-1) for the symbology from which you want to clear the prefix or suffix. Step 3.
Page 114: Suffix Selections
Suffix Selections Add Suffix Clear One Suffix Clear All Suffixes Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are provided in Supported Interface Keys starting on page...
Page 115: Intercharacter Delay
Intercharacter Delay An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each character of scanned data. Scan the Intercharacter Delay bar code below, then scan the number of 5ms delays, and the Save bar code using the Programming Chart inside the back cover of this manual.
Page 116: Interfunction Delay
Interfunction Delay An interfunction delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each segment of the message string. Scan the Interfunction Delay bar code below, then scan the num- ber of 5ms delays, and the Save bar code using the Programming Chart inside the back cover of this manual.
Page 117: Chapter 6 - Data Formatting
Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For exam- ple, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output.
Page 118: Symbology Chart
you are programming. (See Primary/Alternate Data Formats on page 6-10 for further information.) Step 3. Terminal Type Refer to Terminal ID Table (page 6-4) and locate the Terminal ID number for your PC. Scan three numeric bar codes on the inside back cover to program the scanner for your terminal ID (you must enter 3 digits).
Page 119: Other Programming Selections
Other Programming Selections Clear One Data Format This deletes one data format for one symbology. If you are clearing the primary format, scan 0 from the Programming Chart inside the back cover of this manual. If you are clearing an alternate format, scan 1, 2, or 3, depending on the format you are clearing.
Page 120: Terminal Id Table
Terminal ID Table Terminal Terminal Model(s) PC/AT and compatibles USB SurePOS Handheld Scanner USB SurePOS Tabletop Scanner RS232 True RS485 Serial PC Keyboard Mac Keyboard Japanese Keyboard (PC) HID POS Data Format Editor Commands Send Commands Send all characters F1 Include in the output message all of the characters from the input message, starting from current cursor position, followed by an insert character.
Page 121: Ascii Conversion Chart (Code Page 1252)
A-4 for decimal, hex and character codes. Insert symbology name B3 Insert the name of the bar code’s symbology in the output message, without moving the cursor. Only symbologies with a Honeywell ID are included (see Symbology Chart on page A-1).
Page 122: Search Commands
Move the cursor to the end EA Move the cursor to the last character in the input message. Syntax = Search Commands Search forward for a character F8 Search the input message forward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx” character. Syntax = F8xx where xx stands for the search character’s hex value for its ASCII code.
Page 123: Miscellaneous Commands
Search backward for a non-matching character E7 Search the input message backward for the first non-“xx” character from the current cursor position, leaving the cursor pointing to the non- “xx” character. Syntax = E7xx where xx stands for the search character’s hex value for its ASCII code.
Page 124: Data Formatter
example, B2000454657374 will compare the string at the current cursor position with the 4 character string “Test.” Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 for decimal, hex and character codes. Check for a number EC Check to make sure there is an ASCII number at the current cursor position.
Page 125: Data Format Non-Match Error Tone
Data Format Required, Drop Prefix/Suffix Scanned data is modified according to your data format. If a data format is found for a particular symbol, those prefixes and suffixes are not transmitted. Any data that does not match your data format requirements generates an error tone.
Page 126: Primary/Alternate Data Formats
Primary/Alternate Data Formats You can save up to four data formats, and switch between these formats. Your primary data format is saved under 0. Your other three formats are saved under 1, 2, and 3. To set your device to use one of these formats, scan one of the bar codes below.
Page 127 For example, you may have set your device to the data format you saved as Data Format 3. You can switch to Data Format 1 for a single trigger pull by scanning the Single Scan-Data Format 1 bar code below. The next bar code that is scanned uses Data Format 1, then reverts back to Data Format Single Scan-Primary Data Format...
Page 128 6 - 12...
Page 129 Symbologies This programming section contains the following menu selections. Refer to Chapter 11 for settings and defaults. • All Symbologies • Interleaved 2 of 5 • Aztec Code • Korea Post • China Post (Hong Kong 2 of 5) • Matrix 2 of 5 •...
Page 130: All Symbologies
All Symbologies If you want to decode all the symbologies allowable for your scanner, scan the All Symbologies On code. If on the other hand, you want to decode only a particular symbology, scan All Symbologies Off followed by the On symbol for that particular symbology.
Page 131: Codabar
Codabar <Default All Codabar Settings> Codabar On/Off * On Codabar Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit . Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.”...
Page 132: Codabar Concatenation
When Check Character is set to Validate, but Don’t Transmit , the unit will only read Codabar bar codes printed with a check character, but will not transmit the check character with the scanned data. * No Check Character Validate Modulo 16, but Don’t Transmit Validate Modulo 16 and Transmit...
Page 133: Codabar Message Length
Codabar Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60. Minimum Message Length Maximum Message Length 7 - 5...
Page 134: Code 39
Code 39 < Default All Code 39 Settings > Code 39 On/Off * On Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit.
Page 135: Code 39 Message Length
When Check Character is set to Validate and Transmit, the scanner only reads Code 39 bar codes printed with a check character, and will transmit this character at the end of the scanned data. Default = No Check Charac- ter. * No Check Character Validate, but Don’t Transmit Validate and Transmit...
Page 136: Code 32 Pharmaceutical (Paraf)
which the bar codes are read, deleting the first space from each. The scanner transmits the appended data when it reads a Code 39 bar code that starts with a character other than a space. Default = Off. * Off Code 32 Pharmaceutical (PARAF) Code 32 Pharmaceutical is a form of the Code 39 symbology used by Ital- ian pharmacies.
Page 137: Code Page Mapping Of Printed Barcodes
Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #.
Page 138: Interleaved 2 Of 5
and scan the value and the Save bar code from the Programming Chart the inside the back cover of this manual. The data characters should then appear properly. Code 39 Code Page Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 On/Off * On Check Digit...
Page 139: Interleaved 2 Of 5 Message Length
When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit...
Page 140: Nec 2 Of 5
NEC 2 of 5 < Default All NEC 2 of 5 Settings > NEC 2 of 5 On/Off * On Check Digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data.
Page 141 NEC 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length 7 - 13...
Page 142: Code 93 Code Page
Code 93 < Default All Code 93 Settings > Code 93 On/Off * On Code 93 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80.
Page 143: Straight 2 Of 5 Industrial (Three-Bar Start/Stop)
and scan the value and the Save bar code from the Programming Chart the inside the back cover of this manual. The data characters should then appear properly. Code 93 Code Page Straight 2 of 5 Industrial (three-bar start/stop) <Default All Straight 2 of 5 Industrial Settings> Straight 2 of 5 Industrial On/Off * Off Straight 2 of 5 Industrial Message Length...
Page 144: Straight 2 Of 5 Iata (Two-Bar Start/Stop)
Straight 2 of 5 IATA (two-bar start/stop) <Default All Straight 2 of 5 IATA Settings> Straight 2 of 5 IATA On/Off * Off Straight 2 of 5 IATA Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information.
Page 145: Matrix 2 Of 5
Matrix 2 of 5 <Default All Matrix 2 of 5 Settings> Matrix 2 of 5 On/Off * Off Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 1-80.
Page 146: Code 11
Code 11 <Default All Code 11 Settings> Code 11 On/Off * Off Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits. One Check Digit * Two Check Digits 7 - 18...
Page 147: Code 128
Code 11 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 128 <Default All Code 128 Settings>...
Page 148: Code 128 Code Page
that supports concatenation of neighboring symbols, and 4) the standard layout for bar codes on a blood product label. Use the bar codes below to turn concatenation on or off. Default =Off. * Off Code 128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information.
Page 149: Gs1-128
GS1-128 <Default All GS1-128 Settings> GS1-128 On/Off * On GS1-128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 1-80. Minimum Default = 1, Maximum Default = 80.
Page 150: Telepen
Telepen <Default All Telepen Settings> Telepen On/Off * Off Telepen Output Using AIM Telepen Output, the scanner reads symbols with start/stop pat- tern 1 and decodes them as standard full ASCII (start/stop pattern 1). When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and decodes them as compressed numeric with optional full ASCII (start/stop pattern 2).
Page 151: Upc-A
Telepen Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 1-60. Minimum Default = 1, Maximum Default = 60. Minimum Message Length Maximum Message Length UPC-A <Default All UPC-A Settings>...
Page 152 UPC-A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. Default = On. * On UPC-A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-A data.
Page 153: Upc-A/Ean-13
UPC-A Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On UPC-A/EAN-13 with Extended Coupon Code Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code.
Page 154: Upc-E0
UPC-E0 <Default All UPC-E Settings> UPC-E0 On/Off Most U.P.C. bar codes lead with the 0 number system. To read these codes, use the UPC-E0 On selection. If you need to read codes that lead with the 1 number system, use UPC-E1 (page 7-29).
Page 155 UPC-E0 Addenda Required When Required is scanned, the scanner will only read UPC-E bar codes that have addenda. Default = Not Required. Required * Not Required UPC-E0 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda.
Page 156 UPC-E0 Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. To prevent transmission, scan Off. Default = On. * On UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data.
Page 157: Upc-E1
UPC-E1 Most U.P.C. bar codes lead with the 0 number system. For these codes, use UPC-E0 (page 7-26). If you need to read codes that lead with the 1 number system, use the UPC-E1 On selection. Default = Off. UPC-E1 On * UPC-E1 Off EAN/JAN-13 <Default All EAN/JAN Settings>...
Page 158 EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-13 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-13 bar...
Page 159: Isbn Translate
EAN/JAN-13 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = On. * On Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to UPC-A/EAN-13 with Extended Coupon Code (page 7-25).
Page 160: Ean/Jan-8
EAN/JAN-8 <Default All EAN/JAN-8 Settings> EAN/JAN-8 On/Off * On EAN/JAN-8 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On 7 - 32...
Page 161 EAN/JAN-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-8 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-8 bar...
Page 162: Msi
<Default All MSI Settings> MSI On/Off * Off MSI Check Character Different types of check characters are used with MSI bar codes. You can program the scanner to read MSI bar codes with Type 10 check charac- ters. Default = Validate Type 10, but Don’t Transmit. When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI bar codes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned...
Page 163: Msi Message Length
When Check Character is set to Validate Type 10/11, but Don’t Transmit, the unit will only read MSI bar codes printed with the specified type check character(s), but will not transmit the check character(s) with the scanned data. * Validate Type 10, but Don’t Transmit Validate Type 10 and Transmit Validate 2 Type 10 Characters,...
Page 164: Gs1 Databar Omnidirectional
GS1 DataBar Omnidirectional < Default All GS1 DataBar Omnidirectional Settings > GS1 DataBar Omnidirectional On/Off * On GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited On/Off * On 7 - 36...
Page 165: Gs1 Databar Expanded
GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off * On GS1 DataBar Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 4-74.
Page 166: Trioptic Code
Trioptic Code Note: If you are going to scan Code 32 Pharmaceutical codes (page 7-8), Trioptic Code must be off. Trioptic Code is used for labeling magnetic storage media. * Off Codablock A <Default All Codablock A Settings> Codablock A On/Off * Off 7 - 38...
Page 167 Codablock A Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 1-600. Minimum Default = 1, Maximum Default = 600. Minimum Message Length Maximum Message Length 7 - 39...
Page 168: Codablock F
Codablock F <Default All Codablock F Settings> Codablock F On/Off * Off Codablock F Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 1-2048. Minimum Default = 1, Maximum Default = 2048.
Page 169: Pdf417
PDF417 < Default All PDF417 Settings > PDF417 On/Off * On PDF417 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750.
Page 170: Micropdf417
MicroPDF417 < Default All MicroPDF417 Settings > MicroPDF417 On/Off * Off MicroPDF417 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 1-366. Minimum Default = 1, Maximum Default = 366.
Page 171: Gs1 Composite Codes
GS1 Composite Codes Linear codes are combined with a unique 2D composite component to form a new class called GS1 Composite symbology. GS1 Composite symbologies allow for the co-existence of symbologies already in use. * Off UPC/EAN Version Scan the UPC/EAN Version On bar code to decode GS1 Composite sym- bols that have a U.P.C.
Page 172: Gs1 Emulation
GS1 Emulation The scanner can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, ITF-14, GS1-128, and GS1-128 DataBar and GS1 Composites. (Any applica- tion that accepts GS1 data can be simplified since it only needs to recognize one data carrier type.) If GS1-128 Emulation is scanned, all retail codes (U.P.C., UPC-E, EAN8,...
Page 173: Tcif Linked Code 39 (Tlc39)
TCIF Linked Code 39 (TLC39) This code is a composite code since it has a Code 39 linear component and a MicroPDF417 stacked code component. All bar code readers are capable of reading the Code 39 linear component. The MicroPDF417 component can only be decoded if TLC39 On is selected.
Page 174 QR Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 1-7089. Minimum Default = 1, Maximum Default = 7089. Minimum Message Length Maximum Message Length 7 - 46...
Page 175: Data Matrix
Data Matrix < Default All Data Matrix Settings > Data Matrix On/Off * On Data Matrix Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 1-3116. Minimum Default = 1, Maximum Default = 3116.
Page 176: Maxicode
MaxiCode < Default All MaxiCode Settings > MaxiCode On/Off * On MaxiCode Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 1-150. Minimum Default = 1, Maximum Default = 150.
Page 177: Aztec Code
Aztec Code < Default All Aztec Code Settings > Aztec Code On/Off * On Aztec Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 1-3832. Minimum Default = 1, Maximum Default = 3832.
Page 178: Chinese Sensible (Han Xin) Code
Chinese Sensible (Han Xin) Code < Default All Han Xin Settings > Han Xin Code On/Off * Off Han Xin Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Mini- mum and Maximum lengths = 1-7833.
Page 179: Postal Codes - 2D
Postal Codes - 2D The following lists the possible 2D postal codes, and 2D postal code combina- tions that are allowed. Only one 2D postal code selection can be active at a time. If you scan a second 2D postal code selection, the first selection is over- written.
Page 180: Combination 2D Postal Codes
Postnet On Also see Postnet Check Digit, page 7-54. Postnet with B and B’ Fields On InfoMail On Combination 2D Postal Codes: InfoMail and British Post On Intelligent Mail Bar Code and Postnet with B and B’ Fields On Postnet and Postal-4i On Postnet and Intelligent Mail Bar Code On...
Page 181 Planet Code and Postal-4i On Planet Code and Intelligent Mail Bar Code On Planet Code, Postnet, and Postal-4i On Planet Code, Postnet, and Intelligent Mail Bar Code On Planet Code, Postal-4i, and Intelligent Mail Bar Code On Postnet, Postal-4i, and Intelligent Mail Bar Code On Planet Code, Postal-4i, and...
Page 182: Postal Codes - Linear
Planet Code Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of Planet Code data. Default = Don’t Transmit. Transmit Check Digit * Don’t Transmit Check Digit Postnet Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of Postnet data.
Page 183 China Post (Hong Kong 2 of 5) On/Off * Off China Post (Hong Kong 2 of 5) Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maxi- mum Default = 80.
Page 184: Korea Post
Korea Post <Default All Korea Post Settings> Korea Post * Off Korea Post Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maxi- mum Default = 48.
Page 185: Chapter 8 - Imaging Commands
Imaging Commands The scanner is like a digital camera in the way it captures, manipulates, and transfers images. The following commands allow you to alter the way the scan- ner performs these functions. Single-Use Basis Imaging Commands with their modifiers send instructions to the scanner on a single-use basis, and take effect for a single image capture.
Page 186: Image Snap - Imgsnp
Step 1 - Take a Picture Using IMGSNP Image Snap - IMGSNP An image is taken whenever the hardware button is pressed, or when the Image Snap (IMGSNP) command is processed. The image snap command has many different modifiers that can be used to change the look of the image in memory.
Page 187 E - Exposure Exposure is used in Manual Style only (2P), and allows you to set the expo- sure time. This is similar to setting a shutter speed on a camera. The exposure time determines how long the scanner takes to record an image. On a bright day, exposure times can be very short because plenty of light is available to help record an image.
Page 188 W - Target White Value Sets the target for the median grayscale value in the captured image. For capturing close-up images of high contrast documents, a lower setting, such as 75, is recommended. Higher settings result in longer exposure times and brighter images, but if the setting is too high, the image may be overexposed.
Page 189: Image Ship - Imgshp
Step 2 - Ship a Picture Using IMGSHP Image Ship - IMGSHP An image is taken whenever the button is pressed, or when the Image Snap (IMGSNP) command is processed. The last image is always stored in memory. You can “ship” the image by using the IMGSHP command. The image ship commands have many different modifiers that can be used to change the look of the image output.
Page 190 C - Compensation Flattens the image to account for variations in illumination across the image. 0C Compensation disabled (default) 1C Compensation enabled Example of Compensation at 0C: Example of Compensation at 1C: D - Pixel Depth Indicates the number of bits per pixel in the transmitted image (KIM or BMP format only).
Page 191 E - Edge Sharpen An edge sharpen filter cleans up the edges of an image, making it look cleaner and sharper. While edge sharpening does make the image look cleaner, it also removes some fine detail from the original image. The strength of the edge sharpen filter can be entered from 1 to 24.
Page 192 H - Histogram Stretch Increases the contrast of the transmitted image. Not available with some image formats. 0H No stretch (default) 1H Histogram stretch Example of Histogram Stretch at 0H: Example of Histogram Stretch at 1H: I - Invert Image Invert image is used to rotate the image around the X or Y axis.
Page 193 IF- Noise Reduction Used to reduce the salt and pepper noise in an image. 0if No salt and pepper noise reduction (default) 1if Salt and pepper noise reduction Example of Noise Reduction Off (0if): Example of Noise Reduction On (1if): IR - Image Rotate 0ir Image as snapped (rightside up) (default) 1ir Rotate image 90 degrees to the right...
Page 194 J - JPEG Image Quality Sets the desired quality when the JPEG image format is selected. Higher numbers result in higher quality, but larger files. Smaller numbers result in greater amounts of lossy compression, faster transmission times, lower quality, but smaller files. (Default = 50) n J Image is compressed as much as possible while preserving quality factor of n ( n = 0 - 100) 0J worst quality (smallest file)
Page 195 n B The bottom edge of the shipped image corresponds to row n - 1 of the image in memory. Range: 000 - 480. (Default = all rows) Uncropped Image: Example of Image Crop Example of Image set to 300R: Crop set to 300L: Example of Image Crop set to 200B: Example of Image Crop set to 200T:...
Page 196 1S ship every pixel (default) 2S ship every 2nd pixel, both horizontally and vertically 3S ship every 3rd pixel, both horizontally and vertically Example of Pixel Example of Pixel Example of Pixel Ship set to 1S: Ship set to 2S: Ship set to 3S: U - Document Image Filter Allows you to input parameters to sharpen the edges and smooth the area...
Page 197 V - Blur Image Smooths transitions by averaging the pixels next to the hard edges of defined lines and shaded areas in an image. 0V Don’t blur (default) 1V Blur Example of Blur Image Off (0V): Example of Blur Image On (1V): W - Histogram Ship A histogram gives a quick picture of the tonal range of an image, or key type.
Page 198: Intelligent Signature Capture - Imgbox
Image Size Compatibility If you have applications that expect an image ship to return exactly 640x480 pixels, scan the Force VGA Resolution bar code. Default = Native Resolution Force VGA Resolution * Native Resolution Intelligent Signature Capture - IMGBOX IMGBOX allows you to configure the size and location of a signature capture area relative to its proximity to a bar code.
Page 199: Imgbox Modifiers
The following IMGBOX example was executed and viewed using QuickView software. This software is available at www.honeywellaidc.com. Click on Soft- ware Downloads. Select 4600r from the Products list, then select QuickView Software Utility. Below is an example of a signature capture application. In this example, the aimer is centered over the signature capture area and the trigger is pressed.
Page 200 This option is used to size the image horizontally. If using this option, set the resolution (R) to zero. Example of Image Width set to 200A: Example of Image Width set to 600A: B - Output Image Height This option is used to size the image vertically. If using this option, set the resolution (R) to zero.
Page 201 8F BMP format H - Height of Signature Capture Area The height of the signature capture area must be measured in inches divided by .01. In the example, the height of the area to be captured is 3/8 inch, resulting in a value of H = .375/0.01 = 37.5. Example: IMGBOX245w37h55y.
Page 202 For example, use 2500 to specify a resolution of 2.5. Set to zero when using the A and B modifiers (see A - Output Image Width B - Output Image Height on page 8-16). Example of Resolution set to 0R: Example of Resolution set to 1000R: Example of Resolution set to 2000R: S - Bar Code Aspect Ratio...
Page 203: Rf Default Imaging Device
Y - Vertical Bar Code Offset The vertical bar code offset allows you to offset the vertical center of the signature capture area. Negative numbers indicate that the signature cap- ture is above the bar code, and positive numbers indicate that the area is below the bar code.
Page 204 8 - 20...
Page 205: Chapter 9 - Interface Keys
Interface Keys Keyboard Function Relationships The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all terminals that can be used with the scanner. Refer to page 2-19 enable Control + ASCII mode. Function Code HEX/ASCII Value Full ASCII “CTRL”...
Page 206 The last five characters in the Full ASCII “CTRL”+ column ( [ \ ] 6 - ), apply to US only. The following chart indicates the equivalents of these five characters for different countries. Country Codes United States Belgium < Scandinavia <...
Page 207: Supported Interface Keys
Supported Interface Keys IBM AT/XT and IBM XTs and IBM, DDC, PS/2 Compatibles Memorex Telex, ASCII Compatibles, Supported Harris* WYSE PC/AT Keys Supported Keys Supported Keys Reserved Reserved Reserved Enter (KP) CR/Enter Enter Cap Lock Caps Lock ALT make Reserved ALT break Reserved CTRL make...
Page 208 IBM AT/XT and IBM XTs and IBM, DDC, PS/2 Compatibles Memorex Telex, ASCII Compatibles, Supported Harris* WYSE PC/AT Keys Supported Keys Supported Keys * IBM 3191/92, 3471/72, 3196/97, 3476/77, Telex (all models) 9 - 4...
Page 209 Supported Interface Keys IBM, Memorex Telex Memorex Telex (88)** (102)* ASCII Supported Keys Supported Keys Reserved Reserved Enter Enter PF10 PF11 PF12 Reserved Reserved New Line New Line Field Forward Field Forward Reserved Tab/Field Forward Field Forward Delete Delete Field Exit New Line Insert Insert...
Page 210 Supported Interface Keys Esprit 200, 400 Esprit 200, 400 Esprit 200, 400 ANSI ASCII ASCII Supported Supported Supported Keys Keys Keys Reserved Reserved Reserved New Line New Line New Line New Line New Line New Line Delete New Line New Line New Line Insert Escape...
Page 211 Supported Interface Keys Apple Mac/iMac ASCII Supported Keys Reserved Enter/Numpad Enter CAPS ALT make ALT break CNTRL make CNTRL break RETURN APPLE make APPLE break RETURN Ins Help Home Prnt Scrn BACKSPACE LSHIFT TAB BACKSPACE 9 - 7...
Page 212 9 - 8...
Page 213: Chapter 10 - Utilities
Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Chart, beginning on page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D.
Page 214: Show Data Format
Show Data Format Scan the bar code below to show current data format settings. DFMBK3?. Data Format Settings Test Menu When you scan the Test Menu On code, then scan a programming code in this manual, the scanner displays the content of a programming code. The pro- gramming function will still occur, but in addition, the content of that program- ming code is output to the terminal.
Page 215: Application Plug-Ins (Apps)
Application Plug-Ins (Apps) Any apps that you are using can be turned off or on by scanning the following bar codes. Apps are stored in groups: Imaging, Decoding, and Formatting. You can enable and disable these groups of apps by scanning that group’s On or Off bar code below.
Page 216: Installing Ezconfig From The Web
Note: EZConfig requires .NET software. If .NET is not installed on your PC, you will be prompted to install it during the EZConfig installation. 1. Access the Honeywell web site at www.honeywellaidc.com 2. Click on the Resources tab. Select Product Downloads-Software.
Page 217 7. Using Explorer, go to the c:\windows\temp file. 8. Double click on the Setup.exe file. Follow the screen prompts to install the EZConfig program. 9. If you’ve selected the defaults during installation, you can click on Start Menu-All Programs-Honeywell-EZConfig. 10 - 5...
Page 218 10 - 6...
Page 219: Conventions
Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will pro- gram the scanner. For complete descriptions and examples of each serial pro- gramming command, refer to the corresponding programming bar code in this manual.
Page 220: Query Commands
Storage A single character that specifies the storage table to which the command is applied. An exclamation point (!) performs the command’s operation on the device’s volatile menu configuration table. A period (.) performs the command’s operation on the device’s non-volatile menu configuration table.
Page 221: Responses
Responses The device responds to serial commands with one of three responses: ACK Indicates a good command which has been processed. ENQ Indicates an invalid Tag or SubTag command. NAK Indicates the command was good, but the Data field entry was out of the allowable range for this Tag and SubTag combination, e.g., an entry for a minimum message length of 100 when the field will only accept 2 characters.
Page 222: Trigger Commands
MAX60[ACK], DFT[ACK]. This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on; the Start/Stop Character (SSX) is set to 0, or Don’t Transmit; the Check Character (CK2) is set to 0, or Not Required; concatenation (CCT) is set to 1, or Enabled;...
Page 223: Menu Commands
Menu Commands Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Product Default Settings Resetting the Factory Restore Factory DEFOVR Defaults Defaults Save Defaults DEFALT Setting Custom Set Custom Defaults MNUCDF 1-10 Defaults Save Custom DEFALT 1-10 Defaults Resetting the...
Page 224 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Plug and Play Codes: IBM Port 5B PAPP5B RS485 Interface IBM Port 9B PAP9B1 HHBCR-1 Interface IBM Port 17 PAPP17 Interface IBM Port 9B PAP9B2 HHBCR-2 Interface RS485 Packet Mode RTLPDF1 RS485 Packet Mode...
Page 225 Selection Page # Indicates a numeric * Indicates default entry Plug and Play Codes Verifone Ruby PAPRBY Terminal Gilbarco Terminal PAPGLB Honeywell Bioptic PAPBIO Aux Port Datalogic Magellan PAPMAG Bioptic Aux Port NCR Bioptic Aux PAPNCR Port Wincor Nixdorf PAPWNX...
Page 226 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Program Keyboard Czech KBDCTY40 2-11 Country (Programmers) Czech (QWERTY) KBDCTY39 2-11 Czech (QWERTZ) KBDCTY38 2-11 Denmark KBDCTY8 2-11 Dutch (Netherlands) KBDCTY11 2-11 Estonia KBDCTY41 2-12 Faeroese KBDCTY83 2-12 Finland KBDCTY2...
Page 227 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Program Keyboard Latvia (QWERTY) KBDCTY43 2-14 Country Lithuania KBDCTY44 2-14 Lithuania (IBM) KBDCTY45 2-14 Macedonia KBDCTY34 2-14 Malta KBDCTY74 2-14 Mongolian (Cyrillic) KBDCTY86 2-14 Norway KBDCTY9 2-14 Poland KBDCTY20 2-14...
Page 228 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Program Keyboard Ukrainian KBDCTY76 2-16 Country United Kingdom KBDCTY7 2-16 United Stated KBDCTY89 2-16 (Dvorak right) United States KBDCTY88 2-16 (Dvorak left) United States KBDCTY87 2-16 (Dvorak) United States KBDCTY30 2-16...
Page 229 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Keyboard Modifiers *Control + ASCII Off KBDCAS0 2-20 DOS Mode Control KBDCAS1 2-20 + ASCII Windows Mode KBDCAS2 2-20 Control + ASCII Windows Mode KBDCAS3 2-20 Prefix/Suffix Off *Turbo Mode Off KBDTMD0 2-20...
Page 230 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry 2-23 Word Length: Data 7 Data, 1 Stop, 232WRD3 Bits, Stop Bits, and Parity Even Parity 7 Data, 1 Stop, 232WRD0 2-23 Parity None 7 Data, 1 Stop, 232WRD6 2-23 Parity Odd...
Page 231 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Scanner-Bioptic *Bioptic ACK/NAK 232NAK0 2-27 ACK/NAK Mode Bioptic ACK/NAK 232NAK1 2-27 Scanner-Bioptic ACK/NAK Timeout 232DLK##### 2-27 ACK/NAK Timeout *5100 Cordless System Operation Note: This section applies only to cordless systems. It does not apply to corded scanners.
Page 232 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Scanner Modes - Locked Link Mode BASCON0,DNG1 3-11 Single *Open Link Mode BASCON1,DNG1 3-11 Unlink Scanner BT_RMV 3-11 Override Locked BT_RPL1 3-11 Scanner Out-of-Range Alarm Base Alarm BASORD 3-12 Duration (Range 1 -...
Page 233 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Quantity Codes BATNUM0 3-17 BATNUM1 3-17 BATNUM2 3-17 BATNUM3 3-17 BATNUM4 3-17 BATNUM5 3-17 BATNUM6 3-17 BATNUM7 3-17 BATNUM8 3-18 BATNUM9 3-18 Batch Mode Output FIFO BATLIF0 3-18 Order LIFO...
Page 234 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Resetting the Custom Default PAPDFT 3-24 Custom Defaults: All Settings: Application Work All Work Groups Groups Bluetooth PCs/Laptops: BT_DNG5 3-25 Connection Non-Base BT Connection BT Connection - BT_DNG1 3-25 PDA/Mobility...
Page 235 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Beeper Volume - BEPLVL0 Good Read BEPLVL1 Medium BEPLVL2 *High BEPLVL3 Beeper Pitch - Good Low (1600) (min BEPFQ11600 Read (Frequency) 400Hz) *Medium 2700) BEPFQ12700 High (4200) (max BEPFQ14200 9000Hz) Beeper Pitch - Error...
Page 236 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Manual/Serial Trigger *Manual Trigger - PAPHHF Modes Normal Manual Trigger - PAPHHS Enhanced Read Time-Out TRGSTO#### (0 - 300,000 ms) *30,000 Scanner Power BT_LPT0 Time-Out Timer (0- BT_LPT200 7200 seconds) BT_LPT400...
Page 237 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Hands Free Time- Range 0 - 300,000 TRGPTO###### 4-12 Reread Delay Short (500 ms) DLYRRD500 4-12 *Medium (750 ms) DLYRRD750 4-12 Long (1000 ms) DLYRRD1000 4-12 Extra Long (2000 DLYRRD2000 4-12 User-Specified...
Page 238 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Preferred Symbology PRFENA1 4-17 *Off PRFENA0 4-17 High Priority PRFCOD## 4-17 Symbology Low Priority PRFBLK## 4-17 Symbology Preferred PRFPTO#### 4-18 Symbology Timeout (*500) Range 100- 3000 Preferred PRFDFT 4-18 Symbology Default...
Page 239 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Prefix Add Prefix PREBK2## Clear One Prefix PRECL2 Clear All Prefixes PRECA2 Suffix Add Suffix SUFBK2## Clear One Suffix SUFCL2 Clear All Suffixes SUFCA2 Function Code *Enable RMVFNC0 Transmit Disable...
Page 240 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Data Formatter Data Formatter Off DFM_EN0 *Data Formatter On, DFM_EN1 Not Required, Keep Prefix/Suffix Data Format DFM_EN2 Required, Keep Prefix/Suffix Data Formatter On, DFM_EN3 Not Required, Drop Prefix/Suffix Data Format DFM_EN4 Required,...
Page 241 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Codabar Default All Codabar CBRDFT Settings CBRENA0 CBRENA1 Codabar Start/Stop *Don’t Transmit CBRSSX0 Char. Transmit CBRSSX1 Codabar Check *No Check Char. CBRCK20 Char. Validate, But Don’t CBRCK21 Transmit Validate, and CBRCK22...
Page 242 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Code 32 *Off C39B320 Pharmaceutical C39B321 (PARAF) Code 39 Full ASCII *Off C39ASC0 C39ASC1 Code 39 Code Page C39DCP 7-10 Interleaved 2 of 5 Default All I25DFT 7-10 Interleaved 2 of 5 Settings...
Page 243 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Code 93 Default All Code 93 C93DFT 7-14 Settings C93ENA0 7-14 C93ENA1 7-15 Code 93 Message Minimum (0 - 80) *0 C93MIN## 7-14 Length Maximum (0 - 80) C93MAX## 7-14 Code 93 Code Page...
Page 244 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Code 11 Default All Code 11 C11DFT 7-18 Settings *Off C11ENA0 7-18 C11ENA1 7-18 Code 11 Check 1 Check Digit C11CK20 7-18 Digits Required *2 Check Digits C11CK21 7-18 Code 11 Message...
Page 245 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Telepen Output *AIM Telepen Output TELOLD0 7-22 Original Telepen TELOLD1 7-22 Output Telepen Message Minimum (1 - 60) *1 TELMIN## 7-23 Length Maximum (1 - 60) TELMAX## 7-23 UPC-A Default All...
Page 246 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry UPC-E0 Addenda Required UPEARQ1 7-27 Required *Not Required UPEARQ0 7-27 UPC-E0 Addenda UPEADS1 7-27 Separator UPEADS0 7-27 UPC-E0 Check Digit UPECKX0 7-27 UPECKX1 7-27 UPC-E0 Number UPENSX0 7-28 System UPENSX1...
Page 247 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry EAN/JAN-8 Default All EAN/ EA8DFT 7-32 JAN 8 Settings EA8ENA0 7-32 EA8ENA1 7-32 EAN/JAN-8 Check EA8CKX0 7-32 Digit EA8CKX1 7-32 EAN/JAN-8 Addenda *2 Digit Addenda Off EA8AD20 7-33 2 Digit Addenda On EA8AD21...
Page 248 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry MSI Check Character *Validate Type 10, MSICHK0 7-35 but Don’t Transmit Validate Type 10 and MSICHK1 7-35 Transmit Validate 2 Type 10 MSICHK2 7-35 Chars, but Don’t Transmit Validate 2 Type 10 MSICHK3...
Page 249 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry GS1 DataBar Default All GS1 RSEDFT 7-37 Expanded DataBar Expanded Settings RSEENA0 7-37 RSEENA1 7-37 GS1 DataBar Minimum (4 - 74) *4 RSEMIN## 7-37 Expanded Msg. Maximum (4 - 74) RSEMAX## 7-37 Length...
Page 250 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry PDF417 Msg. Length Minimum (1-2750) PDFMIN 7-41 Maximum (1-2750) PDFMAX 7-41 *2750 MicroPDF417 Default All Micro MPDDFT 7-42 PDF417 Settings MPDENA1 7-42 *Off MPDENA0 7-42 MicroPDF417 Msg. Minimum (1-366) *1 MPDMIN 7-42...
Page 251 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry QR Code Msg. Minimum (1-7089) QRCMIN 7-46 Length Maximum (1-7089) QRCMAX 7-46 *7089 Data Matrix Default All Data IDMDFT 7-47 Matrix Settings IDMENA1 7-47 IDMENA0 7-47 Data Matrix Msg. Minimum (1-3116) IDMMIN 7-47...
Page 252 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Chinese Sensible Minimum (1-7833) HX_MIN 7-50 (Han Xin) Code Msg. Length Maximum (1-7833) HX_MAX 7-50 *7833 Postal Codes - 2D 2D Postal Codes *Off POSTAL0 7-51 Single 2D Postal Australian Post On POSTAL1 7-51...
Page 253 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Combination 2D Postal-4i and POSTAL19 7-52 Postal Codes Postnet with B and (continued) B’ Fields On Planet and Postnet POSTAL12 7-52 Planet and Postnet POSTAL18 7-52 with B and B’ Fields Planet and Postal-4i POSTAL13 7-53...
Page 254 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Combination 2D Planet, Postal-4i, POSTAL28 7-53 Postal Codes Intelligent Mail Bar (continued) Code, and Postnet Planet, Postal-4i, POSTAL29 7-53 Intelligent Mail Bar Code, and Postnet with B and B’ Fields Planet Code Check Transmit PLNCKX1...
Page 255 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Imaging Default Commands Image Snap Default all Imaging IMGDFT Commands Imaging Style - SNPSTY0 Decoding *Imaging Style - SNPSTY1 Photo Imaging Style - SNPSTY2 Manual Beeper On SNPBEP1 *Beeper Off SNPBEP0...
Page 256 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Image Ship *Infinity Filter - Off IMGINF0 Infinity Filter - On IMGINF1 *Compensation Off IMGCOR0 Compensation On IMGCOR1 *Pixel Depth - 8 bits/ IMGBPP8 pixel (grayscale) Pixel Depth - 1 bit/ IMGBPP1 pixel (B&W) *Don’t Sharpen...
Page 257 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Image Ship Invert Image around IMGNVX1 (continued) X axis Invert Image around IMGNVY1 Y axis Rotate Image none IMGROT0 Rotate Image 90° IMGROT1 right Rotate Image 180° IMGROT2 right Rotate Image 90°...
Page 258 Serial Command Setting Selection Page # Indicates a numeric * Indicates default entry Image Ship Ship Every 2nd Pixel IMGSUB2 8-12 (continued) Ship Every 3rd Pixel IMGSUB3 8-12 *Document Image IMGUSH0 8-12 Filter Off Document Image IMGUSH### 8-12 Filter On (0-255) *Don’t Ship IMGHST0 8-13...
Page 259: Scanner Product Specifications
Product Specifications 1900 Scanner Product Specifications Parameter Specification Dimensions (Typical): Height 6.3 inches (16 cm) Length 4.1 inches (10.41cm) Width 2.8 inches (7.11cm) Weight 5.2 ounces (147.42g) Illumination: Scan and Aiming LEDs 617nm + 18nm LED output power .339mW Image Size 838 x 640 pixels Skew Angle +65°...
Page 260: Scanner Product Specifications
1902 Scanner Product Specifications Parameter Specification Dimensions (Typical): Height 6.3 inches (16 cm) Length 4.1 inches (10.41cm) Width 2.8 inches (7.11cm) Weight 7.5 ounces (212.62g) Illumination: Scan and Aiming LEDs 617nm + 18nm LED output power .339mW Image Size 838 x 640 pixels Skew Angle +65°...
Page 261: Ccb01-010Bt Charge Base Product Specifications
CCB01-010BT Charge Base Product Specifications Parameter Specification Dimensions (Typical): Height 3.2 inches (8.128cm) Length 5.19 inches (13.183cm) Width 3.98 inches (10.109cm) Weight 6.3 oz (179g) Voltage: 4.5 to 5.5 volts Current Draw: Host Terminal Port 500mA Aux Power Port Charge Time 5 hours Radio: 2.4 to 2.5 GHz (ISM Band) Frequency Hopping...
Page 262: Standard Cable Pinouts
Standard Cable Pinouts Keyboard Wedge 12 - 4...
Page 263: Serial Output
Standard Cable Pinouts Serial Output 12 - 5...
Page 264: Rs485 Output
Standard Cable Pinouts RS485 Output 12 - 6...
Page 265 Standard Cable Pinouts 12 - 7...
Page 266 12 - 8...
Page 267: Repairs
Maintenance Repairs Repairs and/or upgrades are not to be performed on this product. These ser- vices are to be performed only by an authorized service center (see Customer Support on page 14-1). Maintenance Your device provides reliable and efficient operation with a minimum of care. Although specific maintenance is not required, the following periodic checks ensure dependable operation: Cleaning the Device...
Page 268: Replacing An Interface Cable
• Order replacement cables from Honeywell or from an authorized distributor. • When ordering a replacement cable, specify the cable part number of the original interface cable. Replacing an Interface Cable 1. Turn the power to the host system OFF.
Page 269: Changing A Scanner Battery
and press firmly. The connector is keyed to go in only one way, and will click into place. Changing a scanner Battery 1. Loosen the thumbwheel screw on the end cap by hand or use a hex wrench. 2. Remove the battery from the handle.
Page 270: Troubleshooting A Cordless System
If the scanner reads a bar code, but the data is not displayed correctly on the host screen: • The scanner may not be programmed for the appropriate terminal interface. For example, you scan “12345” and the host displays “@es%.” Reprogram the scanner with the correct Plug and Play bar code.
Page 271: Troubleshooting A Cordless Scanner
• The battery is not bad or deeply discharged. In some cases, the scanner’s battery may trickle charge to bring it into an acceptable level and then transition to a normal charge cycle. Troubleshooting a Cordless Scanner Note: Make sure that your scanner’s battery is charged. Visit the Services and Support section of our website (www.honeywellaidc.com) to check for the latest software for both the scanner and the base.
Page 272 13 - 6...
Page 273: Customer Support
E-mail: hsmlasupport@honeywell.com Brazil Telephone: +55 (11) 5185-8222 Fax: +55 (11) 5185-8225 E-mail: brsuporte@honeywell.com Mexico Telephone: 01-800-HONEYWELL (01-800-466-3993) E-mail: soporte.hsm@honeywell.com Europe, Middle East, and Africa Telephone: +31 (0) 40 7999 393 Fax: +31 (0) 40 2425 672 E-mail: hsmeurosupport@honeywell.com Hong Kong...
Page 274: Online Technical Assistance
You can also access technical assistance online at www.honeywellaidc.com. Product Service and Repair Honeywell International Inc. provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, contact the appropriate location below to obtain a Return Material Authorization number (RMA #) before returning the product.
Page 275: Online Product Service And Repair Assistance
You can also access product service and repair assistance online at www.honeywellaidc.com. Limited Warranty Honeywell International Inc. ("HII") warrants its products to be free from defects in materials and workmanship and to conform to HII’s published specifications applicable to the products purchased at the time of shipment. This warranty does not cover any HII product which is (i) improperly installed or used;...
Page 276 HII extends these warranties only to the first end-users of the products. These warranties are non-transferable. The duration of the limited warranty for the Xenon 1900 scanner is five (5) years. The duration of the limited warranty for the Xenon 1902 scanner and CCB01- 010BT Charge Base is three (3) years.
Page 277: Symbology Chart
Reference Charts Symbology Chart Possible AIM ID Code ID Symbology AIM ID Modifiers (hex) ( m ) All Symbologies (0x99) Australian Post A (0x41) ]z m Aztec Code 0-9, A-C z (0x7A) British Post B (0x42) Canadian Post C (0x43) China Post Q (0x51) Chinese Sensible Code (Han Xin...
Page 278 Possible AIM ID Code ID Symbology AIM ID Modifiers (hex) ( m ) EAN-8 with Add-On D (0x44) GS1 Composite ]e m y (0x79) GS1 DataBar ]e m y (0x79) InfoMail , (0x2c) Intelligent Mail Barcode M (0x4D) Interleaved 2 of 5 ]I m 0, 1, 3 e (0x65)
Page 279 Possible AIM ID Code ID Symbology AIM ID Modifiers (hex) ( m ) UPC-A with Add-On c (0x63) UPC-A with Extended c (0x63) Coupon Code UPC-E E (0x45) UPC-E with Add-On E (0x45) UPC-E1 E (0x45) Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Identifiers, for AIM modifier character details.
Page 280 ASCII Conversion Chart (Code Page 1252 Note: This table applies to U.S. style keyboards. Certain characters may differ depending on your Country Code/PC regional settings. Dec Hex Char Hex Char Dec Char Dec Hex Char ‘ “ & ‘ < >...
Page 281 Char Char Dec Char Dec Char € € À à ¡ Á á ‚ ¢ Â â ƒ £ Ã ã „ ¤ Ä ä … ¥ Å å † ¦ Æ æ ‡ § Ç ç ˆ ¨ È è...
Page 282: Code Page Mapping Of Printed Barcodes
Code Page Mapping of Printed Barcodes Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the barcode being scanned was created using a code page that is different from the one the host program is expecting.
Page 283 Sample Symbols UPC-A Interleaved 2 of 5 0 123456 7890 Code 128 1234567890 EAN-13 Code 128 Code 39 9 780330 290951 Codabar BC321 Code 93 A13579B Straight 2 of 5 Industrial 123456-9$ 123456...
Page 284 Sample Symbols Matrix 2 of 5 GS1 DataBar 6543210 PDF417 (01)00123456789012 Car Registration Postnet Zip Code Data Matrix QR Code Test Symbol Numbers 4-CB (4-State Customer Bar Code) 01,234,567094,987654321,01234567891 ID-tag (UPU 4-State) J18CUSA8E6N062315014880T...
Page 285 Sample Symbols Aztec Micro PDF417 Package Label MaxiCode Test Message Test Message...
Page 286: Programming Chart
Programming Chart...
Page 287 Programming Chart Save Discard Reset Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again.
Page 288 Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 Xenon-UG Rev A 5/10...

This manual is also suitable for:

Xenon 1902

Honeywell Xenon 1900 User Manual

Chapter 1 - Getting Started

Chapter 2 - Programming the Interface

Chapter 3 - Cordless System Operation

Chapter 4 - Input/Output Settings

Chapter 5 - Data Editing

Chapter 6 - Data Formatting

Chapter 7 - Symbologies

Chapter 8 - Imaging Commands

Chapter 9 - Interface Keys

Chapter 10 - Utilities

Chapter 11 - Serial Programming Commands

Chapter 12 - Product Specifications

Chapter 13 - Maintenance

Quick Links

Troubleshooting

Related Manuals for Honeywell Xenon 1900

Summary of Contents for Honeywell Xenon 1900