Page 1 Xenon™/Granit™ Xenon 1900, 1900h, 1902, 1902h, 1902g-BF Granit 1910i, 1911i, 1980i, 1981i, 1920i Area-Imaging Scanners User Guide...
Page 2 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.
Page 3: Table Of Contents
TABLE OF CONTENTS Customer Support ........................xvii Technical Assistance ......................xvii Product Service and Repair ..................... xvii Limited Warranty ......................... xvii Send Feedback ........................xvii Chapter 1 - Get Started ..................1 About This Manual......................... 1 Unpack Your Device........................1 Connect the Device........................
Page 4 Aux Port....................23 NCR Bioptic Aux Port........................24 Wincor Nixdorf Terminal ......................24 Wincor Nixdorf Beetle™ Terminal ..................24 Wincor Nixdorf RS232 Mode A....................25 Pair with a Honeywell Vehicle Mount Computer.............25 Keyboard Country Layout......................25 Keyboard Wedge Modifiers......................33 ALT Mode ..........................33 Keyboard Style........................33 Keyboard Conversion......................34 Control Character Output ....................35...
Page 5 RS232 Modifiers...........................37 RS232 Baud Rate........................37 RS232 Word Length: Data Bits, Stop Bits, and Parity..........38 RS232 Receiver Time-Out....................39 RS232 Handshake ........................39 RS232 Timeout........................40 XON/XOFF ..........................40 ACK/NAK...........................40 Scanner to Bioptic Communication ..................41 Scanner-Bioptic Packet Mode..................41 Scanner-Bioptic ACK/NAK Mode..................41 Scanner-Bioptic ACK/NAK Timeout ................42 Chapter 3 - Cordless System Operation: Xenon 1902g/1912 and Granit 1911i/1981i.........43 How the Cordless Charge Base/Access Point Works.............43...
Page 6 Scanner LED Sequences and Meaning ...............51 Base/Access Point LED Sequences and Meaning...........51 Base Power Communication Indicator.................52 Reset Scanner ..........................52 Scan While in Base Cradle......................52 Base Charge Modes........................53 Page ..............................54 Page Mode ..........................54 Page Pitch ..........................54 Error Indicators..........................55 Beeper Pitch - Base Error....................55 Number of Beeps - Base Error ..................55 Scanner Report..........................56 Scanner Address ..........................56...
Page 7 Clear All Codes........................66 Transmit Records to Host....................67 Batch Mode Transmit Delay ....................67 Multiple Scanner Operation ....................67 Scanner Name..........................68 Application Work Groups ......................69 Application Work Group Selection..................70 Reset the Factory Defaults: All Application Work Groups ..........70 Reset the Custom Defaults: All Application Work Groups ...........71 Use the Scanner with Bluetooth Devices................71 Bluetooth Secure Simple Pairing (SSP)................71 Bluetooth HID Keyboard Connect...................72...
Page 8 Program the Scanner and Base .....................83 RF (Radio Frequency) Module Operation ................83 System Conditions ........................84 About the Instant Charge Pack ....................85 Charge Information......................85 Beeper and LED Sequences and Meaning................85 Scanner .............................86 Low Power Alerts..........................86 Low Power Alert Range .......................87 Low Power Alert Flash Number ..................87 Low Power Alert Repeat ......................87 Low Power Alert Beep ......................88 Base..............................88...
Page 9 Scanner Modes ..........................95 Charge Only Mode ........................95 Charge and Link Mode ......................95 Linked Modes..........................95 Unlink the Scanner ........................96 Override Locked Scanner ....................97 Out-of-Range Alarm ........................97 Alarm Sound Type .........................97 Scanner Power Time-Out Timer .....................98 Flexible Power Management ....................99 Batch Mode ..........................100 Batch Mode Beep .......................101 Batch Mode Storage......................101 Batch Mode Quantity ......................102...
Page 10 Chapter 5 - Input/Output Settings............113 Power Up Beeper........................113 Beep on BEL Character ......................114 Trigger Click ..........................114 Good Read and Error Indicators ..................114 Beeper – Good Read......................114 Beeper Volume – Good Read ..................115 Beeper Pitch – Good Read ....................115 Vibrate –...
Page 11 Streaming Presentation In-Stand................128 Mobile Phone Read Mode .....................128 Hands Free Time-Out ......................128 Reread Delay ..........................129 User-Specified Reread Delay ..................129 2D Reread Delay .........................129 Character Activation ........................130 Activation Character......................130 End Character Activation After Good Read ..............131 Character Activation Timeout..................131 Character Deactivation......................131 Deactivation Character ....................132 Illumination Lights ........................132 Aimer Delay..........................132...
Page 12 Multiple Symbols ........................145 No Read ............................146 Video Reverse ..........................146 Working Orientation ........................ 147 Chapter 6 - Healthcare Settings..............149 Quiet Operations - Combination Codes ................149 Silent Mode with Flashing LED ..................149 Silent Mode with Long LED ................... 150 Very Low Beeper (Nighttime Mode)................
Page 13 Clear One or All Prefixes or Suffixes................162 Add a Carriage Return Suffix to All Symbologies...........163 Prefix Selections ........................163 Suffix Selections........................163 Function Code Transmit ......................164 Intercharacter, Interfunction, and Intermessage Delays ..........164 Intercharacter Delay......................164 User Specified Intercharacter Delay ................165 Interfunction Delay......................165 Intermessage Delay ......................166 Chapter 9 - Data Format ................167 Data Format Editor Introduction ..................167 Show Data Format ........................168...
Page 14 NEC 2 of 5............................ 195 Code 93............................197 Straight 2 of 5 Industrial (three-bar start/stop)............198 Straight 2 of 5 IATA (two-bar start/stop)................. 199 Matrix 2 of 5 ..........................200 Code 11............................201 Code 128 ............................202 ISBT 128 Concatenation ....................202 GS1-128 ............................
Page 15 TCIF Linked Code 39 (TLC39)....................228 QR Code ............................228 Data Matrix ..........................230 MaxiCode............................231 Aztec Code ...........................232 Chinese Sensible (Han Xin) Code..................233 Postal Codes - 2D........................234 Planet Code Check Digit....................237 Postnet Check Digit ......................238 Australian Post Interpretation ..................238 Postal Codes - Linear ......................239 China Post (Hong Kong 2 of 5)..................239 Korea Post..........................240 Chapter 11 - Imaging Commands.............241...
Page 16 TotalFreedom..........................262 Application Plug-Ins (Apps) ....................263 EZConfig Cloud for Scanning Introduction ..............263 EZConfig Cloud for Scanning Operations..............264 Install EZConfig Cloud for Scanning................264 Reset the Factory Defaults....................264 Chapter 13 - Serial Programming Commands ........267 Conventions..........................267 Menu Command Syntax ......................
Page 17 Xenon Color Scanner (Model COL) Typical Performance ........319 Xenon Color Scanner (Model COL) Guaranteed Performance ......320 Granit 1910i/1911i Scanner Typical Performance ..........320 Granit 1910i/1911i Scanner Guaranteed Performance ........321 Granit 1980i/1981i Scanner Typical Performance (200 lux)......321 Granit 1980i/1981i Scanner Guaranteed Performance (200 lux)....322 Granit 1920i Typical Performance................323 Granit 1920i Guaranteed Performance..............323 Standard Connector Pinouts....................324...
Page 18 Troubleshoot a Cordless System ..................336 Troubleshoot a Base......................336 Troubleshoot a Cordless Scanner................336 Chapter A - Reference Charts ..............339 Symbology Charts ........................339 Linear Symbologies......................339 2D Symbologies........................340 Postal Symbologies ......................341 ASCII Conversion Chart (Code Page 1252)..............342 Lower ASCII Reference Table ....................
Page 19: Customer Support
Honeywell International Inc. provides service for all of its products through service centers throughout the world. To obtain warranty or non-warranty service, return your product to Honeywell (postage paid) with a copy of the dated purchase record. To learn more, go to www.honeywellaidc.com...
Page 20 xviii Xenon/Granit User Guide...
Page 21: Chapter 1 - Get Started
Granit 1911i and 1981i cordless industrial scanners. Product specifications, dimensions, warranty, and customer support information are also included. Honeywell bar code scanners are factory programmed for the most common ter- minal and communications settings. If you need to change these settings, pro- gramming is accomplished by scanning the bar codes in this guide.
Page 22 1. Connect the appropriate interface cable to the device first, then to the com- puter. Corded Xenon Scanner USB Connection: Corded Granit Scanner USB Connection: Xenon/Granit User Guide...
Page 23 2. If you are connecting a Granit scanner, make sure the cable is pushed tightly into the scanner. Loosen the locking plate and slide it over the base of the cable connector to lock the cable in place. Tighten the screw. CCB01-010BT/CCB01-010BT-07N-BF Base USB Connection: CCB02-100BT/CCB05-100BT Base USB Connection: Note: The power supply must be ordered separately, if needed.
Page 24: Connect With Keyboard Wedge
The unit defaults to a USB PC Keyboard. Refer to page 20 for other USB terminal settings. For additional USB programming and technical information, refer to “USB Applica- tion Note,” available at www.honeywellaidc.com. Connect with Keyboard Wedge A scanner or cordless base can be connected between the keyboard and PC as a “keyboard wedge,”...
Page 25 Corded Granit Scanner Keyboard Wedge Connection: 3. If you are connecting a Granit scanner, make sure the cable is pushed tightly into the scanner. Loosen the locking plate and slide it over the base of the cable connector to lock the cable in place. Tighten the screw. CCB01-010BT/CCB01-010BT-07N-BF Base Keyboard Wedge Connection: Xenon/Granit User Guide...
Page 26: Connect With Rs232 Serial Port
CCB02-100BT/CCB05-100BT Base Keyboard Wedge Connection: Note: The power supply must be ordered separately, if needed. 4. If you are connecting a CCB01-010BT or CCB01-010BT-07N-BF Base, make sure the cables are secured in the wireways in the bottom of the cordless base and the base sits flat on a horizontal surface.
Page 27 Corded Xenon Scanner RS232 Serial Port Connection: Corded Granit Scanner RS232 Serial Port Connection: Xenon/Granit User Guide...
Page 28 3. If you are connecting a Granit scanner, make sure the cable is pushed tightly into the scanner. Loosen the locking plate and slide it over the base of the cable connector to lock the cable in place. Tighten the screw. CCB01-010BT/CCB01-010BT-07N-BF Base RS232 Serial Port Connection: CCB02-100BT/CCB05/100BT Base RS232 Serial Port Connection: Note: The power supply must be ordered separately, if needed.
Page 29: Connect With Rs485
Connect with RS485 A Xenon scanner or cordless base can be connected for an IBM POS terminal inter- face. (This interface is not available in the Granit devices.) 1. Connect the appropriate interface cable to the device, then to the computer. Corded Xenon Scanner RS485 Connection: CCB01-010BT CCB01-010BT-07N-BF Base RS485 Connection:...
Page 30: Mount A Ccb01-010Bt Charge Base
Mount a CCB01-010BT Charge Base 2.36 in. 2.8 in. 59.84mm 72.1mm 3.35 in. 8x32 thread 85.09mm x .39 in. (10mm) deep Mount a CCB02-100BT/CCB05-100BT Base The CCB02-100BT or CCB05-100BT Base can be mounted on either a horizontal or vertical surface. The cables can be routed through either the top or the bottom of the base.
Page 31 When mounted on a vertical surface, a locking system is used to secure the scan- ner when it is in the stand. When mounted on a horizontal surface, the locking mechanism should be set to unlocked (pushed up). When mounted on a vertical surface, the locking mechanism should be set to locked (pushed down).
Page 32: Reading Techniques
Reading Techniques Xenon 1900/1902 and Granit 1910i/1911i The Xenon 1900/1902 scanners have a view finder that projects a bright red aim- ing beam that corresponds to the scanner’s horizontal field of view. The Granit 1910i/1911i scanners have an aiming pattern. The aiming beam or pattern should be centered over the bar code, but it can be positioned in any direction for a good read.
Page 33: Granit 1920I Dpm Scanner
15° to 18° to prevent unwanted reflection. Menu Bar Code Security Settings Honeywell scanners are programmed by scanning menu bar codes or by sending serial commands to the scanner. If you want to restrict the ability to scan menu codes, you can use the Menu Bar Code Security settings.
Page 34: Set Custom Defaults
Set Custom Defaults You have the ability to create a set of menu commands as your own, custom defaults. To do so, scan the Set Custom Defaults bar code below before scanning the menu commands for your custom defaults. If a menu command requires scan- ning numeric codes from the Programming Chart, beginning on page 353, then a...
Page 35 tom defaults, it will reset the scanner to the factory default settings. Any settings that have not been specified through the custom defaults will be defaulted to the factory default settings. Activate Custom Defaults Note: If using a cordless system, scanning this bar code also causes both the scanner and the base or Access Point to perform a reset and become unlinked.
Page 36 Xenon/Granit User Guide...
Page 37: Chapter 2 - Program The Interface
CHAPTER PROGRAM THE INTERFACE Introduction This chapter describes how to program your system for the desired interface. Program the Interface - Plug and Play Plug and Play bar codes provide instant scanner set up for commonly used inter- faces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect.
Page 38: Laptop Direct Connect
Laptop Direct Connect For most laptops, scanning the Laptop Direct Connect bar code allows operation of the scanner in parallel with the integral keyboard. The following Laptop Direct Connect bar code also programs a carriage return (CR) suffix and turns on Emu- late External Keyboard (page 34).
Page 39: Rs485 Packet Mode
IBM Port 17 Interface IBM Port 9B HHBCR-2 Interface Each bar code above also programs the following suffixes for each symbology: Symbolog Suffix Symbology Suffix EAN 8 Code 39 00 0A 0B EAN 13 Interleaved 2 of 5 00 0D 0B UPC A Code 128 * 00 0A 0B...
Page 40: Usb Ibm Surepos
RS485 Packet Length If you are using Packet mode, you can specify the size of the data “packet” that is sent to the host. Scan the Packet Length bar code, then the packet size (from 20 - 256) from the Programming Chart, beginning on page 353, then Save.
Page 41: Usb Hid
No extra configuration (e.g., baud rate) is necessary. Note: If you scan the USB Serial bar code either with an older Honeywell serial driver, or no driver installed, you may no longer be able to scan bar codes. If this happens, either uninstall the older driver versions and install the latest driver, or delete the specific device entry in Device Manager.
Page 42: Ack/Nak Mode
* CTS/RTS Emulation Off ACK/NAK Mode ACK/NAK Mode On * ACK/NAK Mode Off Remote MasterMind™ for USB When using a USB interface, you may wish to configure your scanner to communi- cate with Remote MasterMind Scanner Management Software (ReM). Scan the ReM On bar code to communicate with ReM.
Page 43: Gilbarco ® Terminal
Gilbarco Settings Honeywell Bioptic Aux Port Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit.
Page 44: Ncr Bioptic Aux Port
NCR Bioptic Aux Port Scan the following Plug and Play code to program the scanner for an NCR bioptic scanner auxiliary port configuration. The following prefixes are programmed for each symbology: Symbology Prefix Symbology Prefix UPC-A Interleaved 2 of 5 UPC-E Code 128 Code 32...
Page 45: Wincor Nixdorf Rs232 Mode A
Settings Pair with a Honeywell Vehicle Mount Computer A Xenon/Granit scanner can pair with Honeywell vehicle mount computers, such as the Thor VM1 or VM2, or with Tecton mobile computers. Scan the EZPairing bar code that is either supplied with the vehicle mount com- puter, attached to the vehicle mount computer, or displayed on the screen.
Page 46 lowing characters: # $ @ [ \ ] ^ ‘ { | } ~. Refer to the "ISO 2022/ISO 646 Character Replacements" on page A-346 to view the character replacements for each country. Keyboard Countries * United States Albania Azeri (Cyrillic) Azeri (Latin) Belarus Belgium...
Page 47 Keyboard Countries (Continued) Canada (French legacy) Canada (French) Canada (Multilingual) Croatia Czech Czech (Programmers) Czech (QWERTY) Czech (QWERTZ) Denmark Dutch (Netherlands) Estonia Faroese Xenon/Granit User Guide...
Page 48 Keyboard Countries (Continued) Finland France Gaelic Germany Greek Greek (220 Latin) Greek (220) Greek (319 Latin) Greek (319) Greek (Latin) Greek (MS) Greek (Polytonic) Xenon/Granit User Guide...
Page 49 Keyboard Countries (Continued) Hebrew Hungarian (101 key) Hungary Iceland Irish Italian (142) Italy Japan ASCII Kazakh Kyrgyz (Cyrillic) Latin America Latvia Xenon/Granit User Guide...
Page 50 Keyboard Countries (Continued) Latvia (QWERTY) Lithuania Lithuania (IBM) Macedonia Malta Mongolian (Cyrillic) Norway Poland Polish (214) Polish (Programmers) Portugal Romania Xenon/Granit User Guide...
Page 51 Keyboard Countries (Continued) Russia Russian (MS) Russian (Typewriter) Serbia (Cyrillic) Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation Xenon/Granit User Guide...
Page 52 Keyboard Countries (Continued) Sweden Switzerland (French) Switzerland (German) Tatar Turkey F Turkey Q Ukrainian United Kingdom United States (Dvorak) United States (Dvorak left) United Stated (Dvorak United States (International) Xenon/Granit User Guide...
Page 53: Keyboard Wedge Modifiers
Keyboard Countries (Continued) Uzbek (Cyrillic) Keyboard Wedge Modifiers ALT Mode If your bar code contains special characters from the extended ASCII chart, for example, an e with an accent grave (è), you will use ALT Mode. (See Extended ASCII Characters on page 343.) Note: Scan the ALT mode bar code after scanning the appropriate Keyboard Country code.
Page 54: Keyboard Conversion
Shift Lock is used when you normally have the Shift Lock key on (not common to U.S. keyboards). Shift Lock Automatic Caps Lock is used if you change the Caps Lock key on and off. The soft- ware tracks and reflects if you have Caps Lock on or off . This selection can only be used with systems that have an LED that notes the Caps Lock status (AT key- boards).
Page 55: Control Character Output
* Keyboard Conversion Off Convert All Characters to Upper Case Convert All Characters to Lower Case Control Character Output This selection sends a text string instead of a control character. For example, when the control character for a carriage return is expected, the output would display [CR] instead of the ASCII code of 0D.
Page 56 Default = Control + X Mode Off. Windows Mode Control + X Mode On * Control + X Mode Off DOS Mode Control + X Mode On Windows Mode Prefix/Suffix Turbo Mode: The scanner sends characters to a terminal faster. If the terminal drops characters, do not use Turbo Mode.
Page 57: Rs232 Modifiers
* Automatic Direct Connect Mode Off RS232 Modifiers RS232 Baud Rate Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the scanner. Default = 115,200.
Page 58: Rs232 Word Length: Data Bits, Stop Bits, And Parity
57,600 * 115,200 RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctua- tion), select 7 data bits.
Page 59: Rs232 Receiver Time-Out
* 8 Data, 1 Stop, Parity None 8 Data, 1 Stop, Parity Odd 8 Data, 1 Stop, Parity Mark RS232 Receiver Time-Out The unit stays awake to receive data until the RS232 Receiver Time-Out expires. A manual or serial trigger resets the time-out. When an RS232 receiver is sleeping, a character may be sent to wake up the receiver and reset the time-out.
Page 60: Rs232 Timeout
Two-Direction Flow Control Flow Control with Timeout * RTS/CTS Off RS232 Timeout When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host. Set the length (in milliseconds) for a time- out by scanning the bar code below, then setting the timeout (from 1-5100 milli- seconds) by scanning digits from the Programming Chart,...
Page 61: Scanner To Bioptic Communication
* ACK/NAK Off Scanner to Bioptic Communication The following settings are used to set up communication between Honeywell scan- ners and bioptic scanners. Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with a bioptic scanner.
Page 62: Scanner-Bioptic Ack/Nak Timeout
* Bioptic ACK/NAK Off Bioptic ACK/NAK On Scanner-Bioptic ACK/NAK Timeout This allows you to set the length (in milliseconds) for a timeout for a bioptic scan- ner’s ACK/NAK response. Scan the bar code below, then set the timeout (from 1- 30,000 milliseconds) by scanning digits from the Programming Chart, beginning...
Page 63: Chapter 3 - Cordless System Operation
CHAPTER CORDLESS SYSTEM OPERATION: XENON 1902G/1912 AND GRANIT 1911I/1981I Note: This chapter does not apply to corded or Xenon 1902g-BF scanners. See Cordless System Operation: Xenon 1902g-BF beginning on page 81 for Xenon 1902g-BF scanning systems. How the Cordless Charge Base/Access Point Works A cordless charge base or an Access Point provide the link between the cordless scanner and the host system.
Page 64: Link The Scanner To An Access Point
If the scanner and base have previously been linked, you do not receive any feed- back. If this is the first time that the scanner and base are linked, both devices emit a short chirp when their radios link. At this point, that one scanner is linked to one base.
Page 65: Replace A Linked Scanner
Replace a Linked Scanner If you need to replace a broken or lost scanner that is linked to a base or an Access Point, scan the Override Locked Scanner bar code below with a new scanner and place that scanner in the base, or scan the Access Point linking bar code. The locked link will be overridden;...
Page 66: Program The Scanner And Base Or Access Point
Program the Scanner and Base or Access Point When using the scanner and charge base or Access Point together as a system, menu parameters and configuration settings are stored in the charge base or Access Point. Therefore, when programming any menu configuration settings, the scanner must be linked to the intended charge base or Access Point.
Page 67: Page Button
range and you scan a bar code, the scanner issues an error tone indicating no com- munication with the base or Access Point. A cordless charge base can also sound an alarm. Refer to Out-of-Range Alarm, page 58. Scanner Is Moved Back Into Range The scanner relinks if the scanner or the base or Access Point have been reset, or the scanner comes back into range.
Page 68: Page Button And Presentation Modes
Page Button and Presentation Modes When in Streaming Presentation Mode, the scanner’s aimer goes out after a short time, but the scan illumination remains on all the time to continuously search for bar codes (see Streaming Presentation™ Mode on page 127). When in Temporary Streaming Presentation Mode, pressing the page button on the base puts the scanner into Streaming Presentation Mode until the timeout occurs.
Page 69: Temporary Streaming Presentation Timeout
Temporary Streaming Presentation Timeout Set a timeout for the length of time the illumination remains on and searching for bar codes when using Temporary Streaming Presentation Mode. Set the length for the timeout by scanning one of the bar codes below. Default = 10,000 ms (10 sec- onds).
Page 70: Battery Recommendations
Replace it after the battery is unable to hold an adequate charge. • If you are not sure if the battery or charger is working properly, send it to Honeywell International Inc. or an authorized service center for inspection. Refer to Customer Support on page xvii for additional information.
Page 71: Beeper And Led Sequences And Meaning
labeling, manifesting, and shipping of spent batteries. Contact the Product Service Department (page xvii) for recycling or disposal information. Since you may find that your cost of returning the batteries significant, it may be more cost effective to locate a local recycle/disposal company. Beeper and LED Sequences and Meaning The scanner contains LEDs on the rear of the unit that indicate linking status, decoding state, and battery condition.
Page 72: Base Power Communication Indicator
Green LED - Scanner Battery (base only, does not apply to Access Point) Green LED Charge Condition Battery not detected or charge suspended Slow flash, 1 second on, 1 second off Pre-charge and charging On continuously Charge complete Fast flash, 300 mSec on, 300 mSec off Charge Error Base Power Communication Indicator To display the power indicator on a base or an Access Point, scan the Base Power...
Page 73: Base Charge Modes
Scan in Cradle Off * Scan in Cradle On Shut Down Scanner in Cradle Base Charge Modes When the base has both an external power supply (plugged into the auxiliary power port) and a host interface cable, it will draw its power from the external power sup- ply.
Page 74: Page Mode
External Power Only Page Page Mode By default, the paging button on the base or Access Point pages the scanners associated with that base or Access Point. If you want the paging button on your base or Access Point to be disabled, scan the Page Mode Off bar code, below. When Page Mode is off, the base or Access Point will no longer page scanners when the button is pressed.
Page 75: Error Indicators
High (4200 Hz) Error Indicators Beeper Pitch - Base Error Note: This feature only applies to the CCB01-010BT base. The CCB01-010BT base can be configured to beep at a particular pitch when an error occurs, such as transmission problems to a host system. The beeper pitch codes modify the pitch (frequency) of the error tone the base emits when there is an error.
Page 76: Scanner Report
Scanner Report Scan the bar code below to generate a report for the connected scanners. The report indicates the port, work group, scanner name, and address. To assign a name to your scanner, refer to Menu Command Syntax, page 267. Scanner Report Scanner Address Scan the bar code below to determine the address of the scanner you are using.
Page 77: Charge And Link Mode
In order to program the base for Charge Only Mode, you must link a scanner to it. Once the scanner is linked to the base, scan the Charge Only Mode bar code. Any subsequent scanners placed in that base will charge without linking to it. The scanner used to program the base remains linked to the base.
Page 78: Unlink The Scanner
Open Link Mode - Single Scanner When newly shipped or defaulted to factory settings, a scanner is not linked to a base or an Access Point. A link is established when the scanner is placed into a base, or an Access Point linking bar code is scanned. When in Open Link Mode, a new link is established when a new scanner is placed in the base, or you scan an Access Point linking bar code.
Page 79: Alarm Sound Type
base and to set the alarm duration, scan the appropriate bar code below and then set the time-out duration (from 0-3000 seconds) by scanning digits on the Programming Chart, beginning on page 353, then Save. Default = 0 sec (no alarm). Base Alarm Duration Note: The Access Point does not have a base alarm.
Page 80: Scanner Power Time-Out Timer
Scanner Power Time-Out Timer When there is no activity within a specified time period, the scanner enters low power mode. Scan the appropriate scanner power time-out bar code to change the time-out duration (in seconds). Note: Scanning zero (0) is the equivalent of setting no time-out. If there are no trigger pulls during the timer interval, the scanner goes into power down mode.
Page 81: Flexible Power Management
Flexible Power Management If you are experiencing network performance issues, and suspect the scanner is interfering with other devices, you can turn down the power output of the scanner. This reduces the range between the scanner and a base or an Access Point as shown in the following illustration: 802.11 Scanner...
Page 82: Batch Mode
Access Point once the scanner is back in range or when the records are manually transmitted. Note: Batch Mode is only supported by the Honeywell Charge and Communication Base (CCB) and Honeywell Access Point (AP). Batch mode has limitations when using multiple scanners to one base or Access Point.
Page 83: Batch Mode Beep
Batch Mode Beep When scanning in Inventory Batch Mode (page 62), the scanner beeps every time a bar code is scanned. If using a Granit scanner, it also vibrates. When Batch Mode Beep is On, you will also hear a click when each bar code is sent to the host. If you do not want to hear these clicks, scan Batch Mode Beep Off.
Page 84: Batch Mode Quantity
Batch Mode Quantity When in Batch Mode, you may wish to transmit the number of multiple bar codes scanned, rather than a single bar code multiple times. For example, if you scan three bar codes called XYZ with Batch Mode Quantity Off, when you transmit your data it will appear as XYZ three times.
Page 85 1. Scan the quantity 0 bar code to change the quantity to 1030. 2. Scan the quantity 0 bar code to change the quantity to 0300. 3. Scan the quantity 1 bar code to change the quantity to 3001. 4. Scan the quantity 0 bar code to change the quantity to 0010. Default = 1.
Page 86: Batch Mode Output Order
Batch Mode Output Order When batch data is transmitted, select whether you want that data sent as FIFO (first-in first-out), or LIFO (last-in first-out). Default = Batch Mode FIFO. * Batch Mode FIFO Batch Mode LIFO Total Records If you wish to output the total number of bar codes scanned when in Batch Mode, scan Total Records.
Page 87: Transmit Records To Host
Transmit Records to Host If you are operating in Inventory Batch Mode (see Inventory Batch Mode on page 62), you must scan the following bar code to transmit all the stored data to the host system. Transmit Inventory Records Batch Mode Transmit Delay Sometimes when accumulated scans are sent to the host system, the transmission of those scans is too fast for the application to process.
Page 88: Scanner Name
To put the scanner in multiple scanner mode, scan the bar code below. Once you scan this bar code, the scanner is unlinked from the base or Access Point and must either be placed into the base, or you must scan the Access Point linking bar code in order to relink.
Page 89: Application Work Groups
You could assign all the scanners in the retail area to one work group and those in the warehouse to another. Consequently, any desired changes to either the retail or warehouse area would apply to all scanners in that particular work group. Honeywell’s online configuration tool, EZConfig-Scanning (page 262), makes it easy for you to program your system for use with multiple scanners and multiple work groups.
Page 90: Application Work Group Selection
linked to another Access Point, it will be updated with the new base/Access Point settings for whatever work group to which that the scanner was previously assigned. For example, if the scanner was in work group 1 linked to the first base, it will be placed in work group 1 in the second base with the associated settings.
Page 91: Reset The Custom Defaults: All Application Work Groups
The scanner can be used either with the charge base, an Access Point, or with other Bluetooth devices. Those devices include personal computers, laptops, PDAs, and Honeywell mobility systems devices. Bluetooth Secure Simple Pairing (SSP) Secure Simple Pairing (SSP) allows you to connect simply and securely to other...
Page 92: Bluetooth Hid Keyboard Connect
sion 2.1 or higher. When SSP is on, no PIN is required for pairing. Turn SSP off if you are connecting to a Bluetooth device that is not using a compatible Bluetooth version. Default = Bluetooth SSP On. Note: SSP is only supported by the Granit 1981i scanner. * Bluetooth SSP On Bluetooth SSP Off Bluetooth HID Keyboard Connect...
Page 93 Save Xenon/Granit User Guide...
Page 94: Virtual Keyboard
Non-Base BT Connection PDAs/Mobility Systems Devices You may also use the scanner with a PDA or a Honeywell Mobility Systems device. Scan the bar code below and follow the instructions supplied with your Bluetooth device to locate the scanner, and connect with it.
Page 95: Change The Scanner's Bluetooth Pin Code
Change the Scanner’s Bluetooth PIN Code Some devices require a PIN code as part of the Bluetooth security features. Your scanner’s default PIN is 1234, which you may need to enter the first time you con- nect to your PDA or PC. The PIN code must be between 1 and 16 characters. To change the PIN, scan the bar code below and then scan the appropriate numeric bar codes from the Programming Chart,...
Page 96: Trigger Reconnect Mode
Event Auto Reconnect On Auto Reconnect Off Scanner out of range Relink occurs automatically. If The scanner is relinked by maximum number of link attempts pulling the trigger, or scanning is unsuccessful, then the scanner the Access Point linking bar must be relinked by either pulling code.
Page 97: Relink Time-Out
fere with other users of the ISM band, the number of attempts to connect is limited by this setting. After the maximum number of attempts is reached, the scanner will not attempt to reconnect to a base or an Access Point. Pressing the trigger, scan- ning an Access Point linking bar code, or placing the scanner in the cradle resets the attempt count and the scanner will again try to link.
Page 98: Host Acknowledgment
When the scanner goes out of range, 15 attempts are made to link to the base unit or Access Point. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time. After 15 cycles (8*15 =120), or about 2 minutes, the scanner stops trying to connect to the base or Access Point, but retains any bar codes that may have been saved in batch mode.
Page 99 • A comma must be used as a terminator. • The host terminal software must be capable of interpreting the bar code data, make decisions based on the data content, and send out appropriate escape commands to the scanner. Escape commands are addressed to the scanner via “Application Work Groups.” Once a command is sent, all scanners in a group respond to that command.
Page 100: Host Ack On/Off
Host ACK On/Off Host ACK On * Host ACK Off Host ACK Timeout You can set a timeout for the length of time the scanner waits for a valid escape command when using Host Acknowledgment Mode. Set the length (in seconds) for a timeout by scanning the following bar code, then setting the timeout (from 1-90 seconds) by scanning digits from the Programming Chart,...
Page 101: Chapter 4 - Cordless System Operation: Xenon 1902G-Bf
CHAPTER CORDLESS SYSTEM OPERATION: XENON 1902G-BF Note: This chapter applies only to Xenon 1902g-BF cordless scanning systems. It does not apply to corded scanners, Xenon 1902g/1912, or Granit 1911i/1981i scanners. See Cordless System Operation: Xenon 1902g/1912 and Granit 1911i/1981i beginning on page 43 for other Xenon and Granit cordless scanning systems.
Page 102: Link The Scanner To A Charge Base
Link the Scanner to a Charge Base Xenon Scanner CCB01-010BT-07N-BF Charge Base Page Button and Base LEDs When the base is connected and powered up, put the scanner in the base to estab- lish a link. The green LED on the base flashes to indicate the scanner’s instant charge pack is charging.
Page 103: Communication Between The Cordless System And The Host
Communication Between the Cordless System and the Host The cordless scanner provides immediate feedback in the form of a “good read” indication with a green LED on the scanner and an audible beep. This indicates that the bar code has been scanned correctly and the base has acknowledged receiving the data.
Page 104: System Conditions
of 33 feet (10m) between the scanner and base, depending on the environment. Flexible Power Management, page 99, for information about controlling this range. System Conditions The components of the cordless system interact in specific ways as you associate a scanner to a base, as you move a scanner out of range and bring a scanner back in range.
Page 105: About The Instant Charge Pack
The instant charge pack must be charged before initial use. When the scanner is not in use, return it to the base. The model CCB01-010BT-07N-BF base is designed for use with the Honeywell model Xenon 1902g-BF scanner.
Page 106: Scanner
Scanner Scanner Communication and Scanning The following feedback is provided by the scanner and indicates communication and scanning status. LED Indication Beeper Indication Cause Normal Operation Red Flash None Charge pack low Green Flash 1 beep Successful communication or linking Red, blinking Razz or error tone Failed communication...
Page 107: Low Power Alert Range
Low Power Alert Range Set the power range that will trigger a low power alert. Default = 10-30%. *Low Power Alert 10-30% Low Power Alert 10-50% Low Power Alert Flash Number You can program the scanner’s LEDs to flash up to 9 times for the low power alert. If the Low Power Alert Beep (page 88) is on, a double beep will sound with each...
Page 108: Low Power Alert Beep
Interval Between Alerts If you have set the Low Power Alert Repeat (page 87) to more than 1, you can set the length of time, in seconds, between the low power alerts. To set this interval, scan the bar code below and then scan a digit (10-120) bar code from the Programming Chart, beginning on page 353, then Save.
Page 109: Base Charge Status
Base Charge Status When charging, the base indicates the progress while the scanner resides in the base. Approximate Expected Base Button/LED Charge Level Scans* Green on 100% Green slow blink 50-99% Green fast blink 30-50% Yellow fast blink 0-30% Charging - do not scan * The number of scans was measured with a clearly printed UPC code in good light.
Page 110: Page Button With Scanner Out Of The Base
the interface cable. However, the scanner instant charge pack charges more slowly from a host interface cable than if auxiliary power were available. Using the follow- ing selections, you can specify whether the scanner instant charge pack is charged from power supplied via the host interface cable. When Base Charge Off is selected, the scanner instant charge pack does not charge when the scanner is in the base cradle.
Page 111: Page Button With Scanner In The Base
Page Button with Scanner in the Base When the scanner is in the base, press the page button on the base to begin Streaming Presentation Mode. The scanner acts as a presentation scanner for 10 seconds. If a bar code is scanned before the 10 second timeout is reached, the timer starts over.
Page 112: Paging
Scan in Cradle Off * Scan in Cradle On Shut Down Scanner in Cradle Paging Page Mode When the scanner is out of the base, the paging button on the base pages the scanner associated with that base. If you want to disable the paging button, scan the Page Mode Off bar code, below.
Page 113: Linking Sound
Medium (3250 Hz) High (4200 Hz) Linking Sound Under normal operations, the scanner clicks when linking to a base. If you want to silence this sound, scan the Silent Linking bar code below. To return to the default clicking sound, scan Linking Sound. Default = Linking Sound. * Linking Sound Silent Linking Error Indicators...
Page 114: Number Of Beeps - Base Error
Number of Beeps - Base Error The number of beeps and LED flashes emitted by the base for an error condition can be programmed from 1 - 9. For example, if you program this option to have five error beeps, there will be five error beeps and five LED flashes in response to an error.
Page 115: Scanner Modes
Scanner Modes Charge Only Mode There may be times when you want to charge your scanner, but not link to the base. In order to program the base for Charge Only Mode, you must link the scanner to it. Once the scanner is linked to the base, scan the Charge Only Mode bar code. Any subsequent scanners placed in that base will charge without linking to it.
Page 116: Unlink The Scanner
Locked Link Mode - Single Scanner If you link a scanner to a base using the Locked Link Mode, other scanners are blocked from being linked if they are inadvertently placed into the base. If you do place a different scanner into a base, it will charge the scanner, but the scanner will not be linked.
Page 117: Override Locked Scanner
Override Locked Scanner If you need to replace a broken or lost scanner that is linked to a base, scan the Override Locked Scanner bar code below with a new scanner and place that scan- ner in the base. The locked link is overridden, the broken or lost scanner’s link with the base is removed, and the new scanner is linked to the base.
Page 118: Scanner Power Time-Out Timer
Setting Sound 4 short beeps, high pitch single chirps, medium pitch 2 chirps, then 1 chirp, medium pitch single chirps, high pitch 2 chirps, then 1 chirp, high pitch Base Alarm Type Scanner Alarm Type Scanner Power Time-Out Timer When there is no activity within a specified time period, the scanner enters low power mode.
Page 119: Flexible Power Management
0 seconds 200 seconds * 400 seconds 900 seconds 3600 seconds 7200 seconds Note: When the scanner is in power down mode, pull the trigger to power the unit back up. There will be a set of power up beeps and a delay of up to a few seconds for the radio to join.
Page 120: Batch Mode
Full Power * Medium High Power Medium Power Low Power Batch Mode Batch mode is used to store bar code data when a scanner is out of range of its base, or when performing inventory. The data is transmitted to the base once the scanner is back in range or when the records are manually transmitted.
Page 121: Batch Mode Beep
* Batch Mode Off Automatic Batch Mode Inventory Batch Mode Persistent Batch Mode Batch Mode Beep When scanning in Inventory Batch Mode (page 101), the scanner beeps every time a bar code is scanned. When Batch Mode Beep is On, you will also hear a click when each bar code is sent to the host.
Page 122: Batch Mode Quantity
* Flash Storage RAM Storage Batch Mode Quantity When in Batch Mode, you may wish to transmit the number of multiple bar codes scanned, rather than a single bar code multiple times. For example, if you scan three bar codes called XYZ with Batch Mode Quantity Off, when you transmit your data it will appear as XYZ three times.
Page 123 Example: Add a quantity of 1,500 for the last item scanned. 1. Scan the item's bar code. 2. Scan the quantity 1 bar code. 3. Scan the quantity 5 bar code. 4. Scan the quantity 0 bar code. 5. Scan the quantity 0 bar code. Example: Change a quantity of 103 to 10.
Page 124: Batch Mode Output Order
Quantity Codes (Continued) Batch Mode Output Order When batch data is transmitted, select whether you want that data sent as FIFO (first-in first-out), or LIFO (last-in first-out). Default = Batch Mode FIFO. * Batch Mode FIFO Batch Mode LIFO Total Records If you wish to output the total number of bar codes scanned when in Batch Mode, scan Total Records.
Page 125: Delete Last Code
Delete Last Code If you want to delete the last bar code scanned when in Batch Mode, scan Delete Last Code. Delete Last Code Clear All Codes If you want to clear the scanner’s buffer of all data accumulated in Batch Mode, scan Clear All Codes.
Page 126: Scanner Name
Batch Mode Transmit Delay Short (250 ms) Batch Mode Transmit Delay Medium (500 ms) Batch Mode Transmit Delay Long (1000 ms) Scanner Name You may assign a name to each scanner you are using for identification purposes. The default name is in the format “ScannerName_Model_SN_XXXXXXXXXX” Per- form the rename operation using either the bar codes on page 107, or by sending...
Page 127: Change The Scanner's Bluetooth Pin Code
0006 0007 Reset You may also scan the Scanner Name bar code below and scan a number for the scanner name. For example, if you wanted to name the linked scanner “312,” you would scan the bar code below, scan the 3, 1, and 2 bar codes on the Programming Chart, beginning on page 353, then Save.
Page 128: Auto Reconnect Mode
Auto Reconnect Mode Auto Reconnect controls whether or not the scanner automatically begins the relink process when a loss of connection is detected. When the Auto Reconnect On bar code is scanned, the scanner begins the relink process immediately, without user intervention.
Page 129: Relink Time-Out
number of attempts is reached, the scanner will not attempt to reconnect to a base. Pressing the trigger or placing the scanner in the base resets the counter and the scanner will again try to link. Scan the Maximum Link Attempts bar code, then scan the number of attempts for the setting (from 0-100) from theProgramming Chart, beginning on page 353,...
Page 130: Host Acknowledgment
stops trying to connect to the base, but retains any bar codes that may have been saved in batch mode. After one hour, the scanner powers off and batch mode data is lost. Example: Auto Reconnect Mode set to 0 Maximum Link Attempts set to 15 Other values at default setting When the scanner goes out of range, no action is taken to relink.
Page 131: Host Ack On/Off
The commands to which the scanner responds are listed on page 112. The [ESC] is a 1B in hex. A typical command string is [ESC] x,. [ESC] x is the escape command, and the comma is the terminator, which is required. Example: Commands may be strung together to create custom response sequences.
Page 132: Host Ack Timeout
Host ACK Timeout You can set a timeout for the length of time the scanner waits for a valid escape command when using Host Acknowledgment Mode. Set the length (in seconds) for a timeout by scanning the following bar code, then setting the timeout (from 1-90 seconds) by scanning digits from the Programming Chart, beginning on page 353,...
Page 133: Chapter 5 - Input/Output Settings
CHAPTER INPUT/OUTPUT SETTINGS Power Up Beeper Note: This feature does not apply to the CCB02-100BT/CCB05-100BT base. The scanner can be programmed to beep when it’s powered up. If you are using a cordless system, the base can also be programmed to beep when it is powered up. Scan the Off bar code(s) if you don’t want a power up beep.
Page 134: Beep On Bel Character
Beep on BEL Character You may wish to force the scanner to beep upon a command sent from the host. If you scan the Beep on BEL On bar code below, the scanner will beep every time a BEL character is received from the host. Default = Beep on BEL Off. *Beep on BEL Off Beep on BEL On Trigger Click...
Page 135: Beeper Volume - Good Read
Beeper Volume – Good Read The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High for Granit/Xenon, Low for Xenon HC. * Low Medium * High Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read.
Page 136: Beeper Pitch - Error
The scanner vibrates once when a bar code is successfully read, and twice when a programming bar code is successfully read. When a programming bar code is unsuccessful, the scanner emits one long vibration (2 times the Vibrate Duration length). Scan Vibrate - Good Read Off to keep the scanner from vibrating. Default = Vibrate - Good Read On.
Page 137: Beeper Duration - Good Read
Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read. Default = Normal. * Normal Beep Short Beep Short Beep LED – Good Read The LED indicator can be programmed On or Off in response to a good read. Default = On.
Page 138: Beeper Volume Max
to an error. To change the number of error beeps, scan the bar code below and then scan a digit (1-9) bar code from the Programming Chart, beginning on page 353, then Save. Default = 1. Number of Error Beeps/LED Flashes Beeper Volume Max Note: The Beeper Volume Max feature only applies to Granit products.
Page 139: User-Specified Good Read Delay
User-Specified Good Read Delay If you want to set your own length for the good read delay, scan the bar code below, then set the delay (from 0 - 30,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 353, then Save. User-Specified Good Read Delay Trigger Modes Manual Trigger...
Page 140 *Trigger Toggle Off Trigger Toggle - Image Capture Trigger Toggle - Cell Phone Read Trigger Toggle - Centering Trigger Number This sets the number of trigger preses required to activate the Trigger Toggle Mode. 2 Quick Triggers 3 Quick Triggers 4 Quick Triggers Trigger Timing This sets the timing of the trigger presses in order to qualify as a trigger toggle,...
Page 141: Serial Trigger
Trigger Toggle Timeout This sets the length of time the scanner stays in trigger toggle mode before revert- ing to scan mode. After scanning the Trigger Toggle Timeout bar code, set the time-out duration (from 0 to 65 seconds) by scanning digits from the Programming Chart, beginning on page 353, then Save.
Page 142: Presentation Mode
Presentation Mode Presentation Mode uses ambient light and scanner illumination to detect bar codes. When in Presentation Mode, the LEDs remain dim until a bar code is pre- sented to the scanner, then the aimer turns on and the LEDs turn up to read the code.
Page 143: Presentation Centering
Presentation Centering Use Presentation Centering to narrow the scanner’s field of view when it is in the stand to make sure the scanner reads only those bar codes intended by the user. For instance, if multiple codes are placed closely together, Presentation Centering will insure that only the desired codes are read.
Page 144: In-Stand Sensor Mode
Scan Presentation Centering On, then scan one of the following bar codes to change the top, bottom, left, or right of the centering window. Then scan the per- cent you want to shift the centering window from the Programming Chart, begin- ning on page 353, then Save.
Page 145: Poor Quality Codes
This feature senses when the scanner is removed from the stand and tells it to begin manual triggering. When Sensor On is enabled, the scanner defaults to Streaming Presentation Mode when it is in the stand, and to Manual Trigger Mode when it is removed from the stand.
Page 146: Poor Quality Pdf Codes
Poor Quality PDF Codes This setting improves the scanner’s ability to read damaged or badly printed PDF codes by combining information from multiple images. It is useful when a com- plete bar code cannot be seen in one image. This setting does not affect 1D bar code reading.
Page 147: Codegate
® CodeGate Note: CodeGate is not supported by the Granit 1980i and 1981i. When CodeGate is On, the trigger is used to allow decoded data to be transmitted to the host system. The scanner remains on, scanning and decoding bar codes, but the bar code data is not transmitted until the trigger is pressed.
Page 148: Streaming Presentation In-Stand
Streaming Presentation In-Stand This option is available when using In-Stand Sensor Mode, page 124. You may pro- gram a specific Streaming Presentation Mode for in-stand scanning, and a Manual Trigger mode for out-of-stand scanning. To do this, you must first scan the pre- ferred Streaming Presentation mode (Normal, Enhanced, or Mobile Phone), then scan the Manual Trigger mode (Normal, Enhanced, or Mobile Phone) you want to use.
Page 149: Reread Delay
Reread Delay This sets the time period before the scanner can read the same bar code a second time. Setting a reread delay protects against accidental rereads of the same bar code. Longer delays are effective in minimizing accidental rereads. Use shorter delays in applications where repetitive bar code scanning is required.
Page 150: Character Activation
Short (1000ms) Medium (2000ms) Long (3000ms) Extra Long (4000ms) Character Activation You may use a character sent from the host to trigger the scanner to begin scan- ning. When the activation character is received, the scanner continues scanning until either the Character Activation Timeout (page 5-131), the deactivation char- acter is received (see...
Page 151: End Character Activation After Good Read
End Character Activation After Good Read After a bar code is successfully detected and read from the scanner, the illumina- tion can be programmed either to remain on and scanning, or to turn off. When End Character Activation After Good Read is enabled, the illumination turns off and stops scanning after a good read.
Page 152: Deactivation Character
Deactivation Character This sets the character used to terminate scanning when using Character Deacti- vation Mode. On the ASCII Conversion Chart (Code Page 1252), page 342, find the hex value that represents the character you want to use to terminate scanning. Scan the following bar code, then use the Programming Chart, beginning on page...
Page 153: User-Specified Aimer Delay
500 milliseconds * Off (no delay) User-Specified Aimer Delay If you want to set your own length for the duration of the delay, scan the bar code below, then set the time-out by scanning digits (0 - 4,000 ms) from the Programming Chart, beginning on page 353, then Save.
Page 154: Laser Aimer - Scan Duration
Laser Aimer - Scan Duration Note: Only the Granit 1910i, 1911i, 1980i, and 1981i support this feature. Use the following bar codes to specify how long you want the laser aimer to remain on after the trigger is released. Scan the 10 Second Scan Duration bar code to set the duration to 10 seconds (default setting for Granit 1910i1D/1911i1D scan- ners).
Page 155: Custom Centering
Custom Centering Use the following settings to customize your centering window. If a bar code is not touched by a predefined window, it will not be decoded or output by the scanner. If centering is turned on by scanning Centering On, the scanner only reads codes that pass through the centering window you specify using the Top of Centering Window, Bottom of Centering Window, Left, and Right of Centering Window bar codes.
Page 156: Preferred Symbology
* Centering Off Top of Centering Window Bottom of Centering Window Left of Centering Window Right of Centering Window Preferred Symbology The scanner can be programmed to specify one symbology as a higher priority over other symbologies in situations where both bar code symbologies appear on the same label, but the lower priority symbology cannot be disabled.
Page 157: High Priority Symbology
Scan a bar code below to enable or disable Preferred Symbology. Default = Pre- ferred Symbology Off. Preferred Symbology On * Preferred Symbology Off High Priority Symbology To specify the high priority symbology, scan the High Priority Symbology bar code below.
Page 158: Preferred Symbology Default
encountered. Scan the bar code below, then set the delay (from 1-3,000 millisec- onds) by scanning digits from the Programming Chart, beginning on page 353, then Save. Default = 500 ms. Preferred Symbology Time-out Preferred Symbology Default Scan the bar code below to set all Preferred Symbology entries to their default val- ues.
Page 159: Output Sequence Editor Commands
3. Length Specify what length (up to 9999 characters) of data output will be acceptable for this symbology. Make a note of the length. If you are using bar codes to create your output sequence, scan the 4 digit data length Programming Chart, beginning on page 353.
Page 160 Output Sequence Example 1 - Three Symbologies In this example, you are scanning PDF417, Code 128, and Code 39 bar codes, but you want the scanner to output Code 39 first, Code 128 second, and PDF417 third. Set up the sequence editor with the following command line: SEQBLK sequence editor start command code identifier for Code 39...
Page 161 Output Sequence Example 2 - Three Symbologies with <> Separators In this example, you are scanning the same three bar codes, but you want <> brack- ets and a carriage return and line feed to separate your output. The sequence editor would use the same command line as shown in Output Sequence Example 1 - Three Symbologies (page 140):...
Page 162: Enter Output Sequence
line feed The whole command line would look like this: SEQBLK62999943FF6A999954FF7299994DFFSEQSEP993C3ESEQSUF990D0 The data is output as: <CODE39SMPL> <TSTMSGCODE128> <MSGPDF417> Enter Output Sequence If you are using bar codes to create your output sequence, scan Enter Output Sequence to begin scanning your string. Enter Output Sequence Partial Sequence If an output sequence operation is terminated before all your output sequence cri-...
Page 163 You would use the same command line as shown in Output Sequence Example 2 - Three Symbologies with <> Separators (page 141): SEQBLK sequence editor start command code identifier for Code 39 9999 code length that must match for Code 39, 9999 = all lengths start character match for Code 39, 43h = "C"...
Page 164 left bracket (<) The whole command line would look like this: SEQBLK62999943FF6A999954FF7299994DFFSEQSEP993C3ESEQSUF990D0 ASEQTTS1SEQISU993E5041525449414C3C The data is output as: >PARTIAL< <TSTMSGCODE128> <MSGPDF417> Discard Partial Output Sequence If you want to discard partial sequences when the output sequence operation is terminated before completion, scan Discard Partial Sequence. * Discard Partial Sequence Default Output Sequence Default Sequence programs the scanner to all universal values.
Page 165: Good Read Tone - Output Sequences
Required On/Not Required *Off Good Read Tone - Output Sequences Note: Partial sequence programming is only supported by Granit 1910i and Granit 1911i scanners. The scanner may be programmed to either beep or click in response to a good read of each bar code in an output sequence, or to emit a beep or error tone for a partial sequence.
Page 166: No Read
(if turned on) for each read. If using a Granit scanner, the scanner also vibrates. The scanner attempts to find and decode new symbols as long as the trigger is pulled. When this programming selection is turned Off, the scanner will only read the sym- bol closest to the aiming beam.
Page 167: Working Orientation
Video Reverse Only Video Reverse and Standard Bar Codes * Video Reverse Off Working Orientation Some bar codes are direction-sensitive. For example, KIX codes and OCR can mis- read when scanned sideways or upside down. Use the working orientation settings if your direction-sensitive codes will not usually be presented upright to the scan- ner.
Page 168 Vertical, Bottom to Top Upside Down Vertical, Top to Bottom Xenon/Granit User Guide...
Page 169: Chapter 6 - Healthcare Settings
CHAPTER HEALTHCARE SETTINGS The following settings have been developed to enhance scanning in a healthcare environment. These settings are only supported by the Xenon 1900h scanner and Xenon 1902h scanner and base. They allow you to set quickly configure streaming presentation, and to set the scanner and base to quiet modes for scanning that do not disturb resting patients.
Page 170: Silent Mode With Long Led
Silent Mode with Long LED Scan the following bar code to completely silence the Xenon 1900h scanner or Xenon 1902h scanner and base. The scanner beep, base beep, base and scanner power up beep, and scanner linking sounds are all silenced. When a bar code is scanned, the LED and aimer remain solidly lit for 1 second.
Page 171: Low Beeper (Daytime Mode)
Low Beeper (Daytime Mode) The following bar code sets all sounds to on, but at a low volume. The scanner beep, base beep, base and scanner power up beep, and scanner linking sounds are all set to low volume. Daytime Mode - Cordless Scanner and Base Daytime Mode - Corded Scanner...
Page 172: Number Of Led Flashes
Number of LED Flashes If you have silenced the scanner’s beeper, you may set the number of times the LED flashes when reading bar codes. Default = 1 LED Flash. Note: If you have set LED Solid (No Flash) (page 153), to anything but Off, that setting will override the LED Flash settings.
Page 173: Led Solid (No Flash)
LED Solid (No Flash) Under normal operations, the scanner’s LED flashes once for a good read. You may set the LED to remain on for a length of time after a good read instead of flashing. Default = LED Solid Off (Resume Flash). * LED Solid Off (Resume Flash) LED Solid 1 Second...
Page 174: Out-Of-Range Alarm Volume
Page Volume Medium Page Volume High Out-of-Range Alarm Volume Note: This setting is not supported by the Xenon 1900h scanner. If your scanner is out range of the base, an alarm sounds from both your base and scanner. If your scanner is out range of an Access Point, an alarm sounds from just the scanner.
Page 175: Out-Of-Range Delay
Base Alarm Volume High Scanner Alarm Volume High Out-of-Range Delay Note: This setting is not supported by the Xenon 1900h scanner. When using the Out-of-Range Alarm settings, the length of the delay for the alarm is set with an Out-of-Range Delay. When the scanner is out of range of the base or Access Point, the alarm will delay for a set length of time before going off.
Page 176 Xenon/Granit User Guide...
Page 177: Chapter 7 - Direct Part Mark (Dpm) Settings
CHAPTER DIRECT PART MARK (DPM) SETTINGS The following settings have been developed for the Granit 1920i scanner and are supported only by that device. DPM Illumination Settings Cycle Illumination This is the default setting for the Granit 1920i. Cycle Illumination cycles through the Direct Illumination - Top and Bottom, and Indirect Illumination settings.
Page 178: Direct Illumination - Top And Bottom
Direct Illumination - Top and Bottom This setting enables both top and bottom illumination. It is recommend when read- ing printed label bar codes and DPMs on highly reflective surfaces. Direct Illumination - Top and Bottom Direct Illumination - Bottom This setting enables just the bottom illumination.
Page 179 Low Contrast Data Matrix Enhancements Off Xenon/Granit User Guide...
Page 180 Xenon/Granit User Guide...
Page 181: Chapter 8 - Data Edit
CHAPTER DATA EDIT Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string.
Page 182: Add A Prefix Or Suffix
• When setting up for specific symbologies (as opposed to all symbologies), the specific symbology ID value counts as an added prefix or suffix character. • The maximum size of a prefix or suffix configuration is 200 characters, which includes header information. Add a Prefix or Suffix: Step 1.
Page 183: Add A Carriage Return Suffix To All Symbologies
Step 1. Scan the Clear One Prefix or Clear One Suffix symbol. Step 2. Determine the 2 digit hex value from the Symbology Chart (included in Symbology Charts, beginning on page 339) for the symbology from which you want to clear the prefix or suffix. Step 3.
Page 184: Function Code Transmit
Clear All Suffixes Function Code Transmit By default, all ASCII control characters are transmitted with bar code data. These non-printable characters are translated into predefined key strokes, or CTRL+X functions (see ASCII Conversion Chart (Code Page 1252), beginning on page 342). If these key strokes interfere with your host’s software application, scan Disable to keep these ASCII control characters from being transmitted.
Page 185: User Specified Intercharacter Delay
To remove this delay, scan the Intercharacter Delay bar code, then set the number of delays to 0. Scan the Save bar code from the Programming Chart, beginning on page 353. Note: Intercharacter delays are not supported in USB serial emulation. User Specified Intercharacter Delay An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed after the transmission of a particular character of scanned data.
Page 186: Intermessage Delay
To remove this delay, scan the Interfunction Delay bar code, then set the number of delays to 0. Scan the Save bar code from the Programming Chart, beginning on page 353. Intermessage Delay An intermessage delay of up to 5000 milliseconds (in 5ms increments) may be placed between each scan transmission.
Page 187: Chapter 9 - Data Format
CHAPTER DATA FORMAT Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output.
Page 188: Show Data Format
If you have changed data format settings, and wish to clear all formats and return to the factory defaults, scan the Default Data Format code below. * Default Data Format Show Data Format Scan the bar code below to show current data format settings. Data Format Settings Add a Data Format Step 1.
Page 189: Other Programming Selections
this symbology. Scan the four digit data length from the Programming Chart, beginning on page 353. For example, 50 characters is entered as 0050. Note: 9999 indicates all lengths. Step 6. Editor Commands Refer to Data Format Editor Commands (page 170). Scan the symbols that represent the command you want to enter.
Page 190: Terminal Id Table
Save Discard Terminal ID Table Terminal Model(s) Terminal ID PC keyboard (HID) Mac Keyboard PC Keyboard (Japanese) Serial (COM driver required) HID POS USB SurePOS Handheld USB SurePOS Tabletop Serial RS232 TTL RS232 True RS485 (IBM-HHBCR 1+2, 46xx) Keyboard PS2 compatibles AT compatibles Data Format Editor Commands When working with the Data Format Editor, a virtual cursor is moved along your...
Page 191 Send a number of characters F2 Include in the output message a number of characters followed by an insert character. Start from the current cursor position and continue for “nn” characters or through the last character in the input message, followed by character “xx.” Syntax = F2nnxx where nn stands for the numeric value (00-99) for the number of characters, and xx stands for the insert character’s hex value for its ASCII code.
Page 192 Send all characters up to a particular character F3 Include in the output message all characters from the input message, starting with the character at the current cursor position and continuing to, but not including, the search character “ss,” followed by an insert character. The cursor is moved forward to the “ss”...
Page 193 42 is the hex value for B The data is output as: 1234567890 Send all but the last characters E9 Include in the output message all but the last “nn” characters, starting from the current cursor position. The cursor is moved forward to one position past the last input message character included.
Page 194 1234567890**ABCDEFGHIJ <CR> Insert symbology name B3 Insert the name of the bar code’s symbology in the output message, without moving the cursor. Only symbologies with a Honeywell ID are included (see Symbology Charts on page 339). Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 342 for decimal, hex and character codes.
Page 195 B3 is the “Insert symbology name” command F4 is the “Insert a character multiple times” command 20 is the hex value for a space 01 is the number of times the space character is sent B4 is the “Insert bar code length” command F4 is the “Insert a character multiple times”...
Page 196: Move Commands
If there are three keystrokes, the syntax would change from B5xxssnn for one key- stroke to B5xxssnnssnnssnn. An example that would insert "abc" is as follows: B503001F00320030F833. Note: Key modifiers can be added together when needed. The sum is converted to hexadecimals.
Page 197: Search Commands
FE and F7 Example: Manipulate bar codes that begin with a 1 Search for bar codes that begin with a 1. If a bar code matches, move the cursor back to the beginning of the data and send 6 characters followed by a carriage return.
Page 198 F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: DEFGHIJ <CR> Search backward for a character F9 Search the input message backward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx”...
Page 199 Search backward for a string B1 Search backward for “s” string from the current cursor position, leaving cursor pointing to “s” string. Syntax = B1nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B1000454657374 will search backward for the first occurrence of the 4 character string “Test.”...
Page 200: Miscellaneous Commands
Miscellaneous Commands Suppress characters FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is advanced by other commands. When the FC command is encountered, the suppress function is terminated. The cursor is not moved by the FB command.
Page 201 If the bar code has characters that the host application does not want included, you can use the E4 command to replace those characters with something else. In this example, you will replace the zeros in the bar code above with carriage returns. Command string: E402300DF10D E4 is the “Replace characters”...
Page 202 EC Example: Only output the data if the bar code begins with a number If you want only data from bar codes that begin with a number, you can use EC to check for the number. Command string: ECF10D EC is the “Check for a number” command F1 is the “Send all characters”...
Page 203: Data Formatter
Insert a delay EF Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting from the current cursor position. Syntax = EFnnnn where nnnn stands for the delay in 5ms increments, up to 9999. This command can only be used with keyboard emulation. Discard Data B8 Discards types of data.
Page 204: Data Format Non-Match Error Tone
requirements generates an error tone and the data in that bar code is not transmitted. If you wish to process this type of bar code without generating an error tone, see Data Format Non-Match Error Tone. • Data Format Required, Drop Prefix/Suffix Scanned data is modified according to your data format.
Page 205: Primary/Alternate Data Formats
Data Format Non-Match Error Tone Off Primary/Alternate Data Formats You can save up to four data formats, and switch between these formats. Your pri- mary data format is saved under 0. Your other three formats are saved under 1, 2, and 3.
Page 206 Single Scan-Data Format 1 Single Scan-Data Format 2 Single Scan-Data Format 3 Xenon/Granit User Guide...
Page 207: Chapter 10 - Symbologies
CHAPTER SYMBOLOGIES This programming section contains the following menu selections. Refer to Chapter 13 for settings and defaults. • All Symbologies • Interleaved 2 of 5 • Aztec Code • Korea Post • China Post (Hong Kong 2 of 5) •...
Page 208: All Symbologies
All Symbologies For best scanner performance, we recommend you only enable the symbologies that you need. Scan All Symbologies Off to disable all symbologies, then enable the symbologies you need by scanning the On bar code for each symbology. All Symbologies Off Message Length Description You are able to set the valid reading length of some of the bar code symbologies.
Page 209 Codabar Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Trans- mit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.” You can program the scanner to read only Codabar bar codes with Modulo 16 check characters.
Page 210 Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concate- nated into one with the “D” characters omitted. A 1 2 3 4 D D 5 6 7 8 A Select Require to prevent the scanner from decoding a single “D”...
Page 211: Code 39
Code 39 < Default All Code 39 Settings > Code 39 On/Off * On If you are reading Code 39 bar codes, Codablock A should remain disabled. If you are enabling Codablock A (see Codablock A on page 222), you should disable Code Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code.
Page 212 When Check Character is set to Validate and Transmit, the scanner only reads Code 39 bar codes printed with a check character, and will transmit this character at the end of the scanned data. Default = No Check Character. * No Check Character Validate, but Don’t Transmit Validate and Transmit Code 39 Message Length...
Page 213 Code 32 Pharmaceutical (PARAF) Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian phar- macies. This symbology is also known as PARAF. Note: Trioptic Code (page 221) must be turned off while scanning Code 32 Pharmaceutical codes.
Page 214: Interleaved 2 Of 5
* Full ASCII Off Code 39 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting.
Page 215: Nec 2 Of 5
When Check Digit is set to Validate and Transmit, the scanner only reads Inter- leaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit...
Page 216 Check Digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data.
Page 217: Code 93
Code 93 < Default All Code 93 Settings > Code 93 On/Off * On Code 93 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 188) for additional information. Minimum and Maximum lengths = 0-80.
Page 218: Straight 2 Of 5 Industrial (Three-Bar Start/Stop)
* Off Code 93 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting.
Page 219: Straight 2 Of 5 Iata (Two-Bar Start/Stop)
Straight 2 of 5 Industrial Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 188) for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length Straight 2 of 5 IATA (two-bar start/stop)
Page 220: Matrix 2 Of 5
code. To adjust the redundancy, scan the Straight 2 of 5 IATA Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart, beginning on page 353. Then scan the Save bar code. Default = 0. Straight 2 of 5 IATA Redundancy Straight 2 of 5 IATA Message Length...
Page 221: Code 11
Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 188) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 11...
Page 222: Code 128
Code 11 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 188) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 128 <Default All Code 128 Settings>...
Page 223 design, 3) a variation of Code 128 that supports concatenation of neighboring symbols, and 4) the standard layout for bar codes on a blood product label. Use the bar codes below to turn concatenation on or off. Default =Off. * Off Code 128 Redundancy If you are encountering errors when reading Code 128 bar codes, you may want to adjust the redundancy count.
Page 224: Gs1-128
Code 128 bar codes until it reads a Code 128 bar code that does not have the append trigger. The data is then transmitted in the order in which the bar codes were read (FIFO). Default = Off. * Off Code 128 Code Page Code pages define the mapping of character codes to characters.
Page 225: Telepen
GS1-128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 188) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 1, Maximum Default = 80. Minimum Message Length Maximum Message Length Telepen <Default All Telepen Settings>...
Page 226: Upc-A
Original Telepen Output Telepen Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 188) for additional information. Minimum and Maximum lengths = 1-60. Minimum Default = 1, Maximum Default = 60. Minimum Message Length Maximum Message Length UPC-A...
Page 227 UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On UPC-A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the begin- ning of the scanned data, but can be programmed so it is not transmitted (Off).
Page 228 UPC-A Addenda Required When Required is scanned, the scanner will only read UPC-A bar codes that have addenda. You must then turn on a 2 or 5 digit addenda listed on page 207. Default = Not Required. Required * Not Required Addenda Timeout You can set a time during which the scanner looks for an addenda.
Page 229: Upc-A/Ean-13 With Extended Coupon Code
UPC-A/EAN-13 with Extended Coupon Code Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. When left on the default setting (Off), the scanner treats Coupon Codes and Extended Coupon Codes as single bar codes. If you scan the Allow Concatenation code, when the scanner sees the coupon code and the extended coupon code in a single scan, it transmits both as one sym- bologies.
Page 230: Coupon Gs1 Databar Output
Coupon GS1 DataBar Output If you scan coupons that have both UPC and GS1 DataBar codes, you may wish to scan and output only the data from the GS1 DataBar code. Scan the GS1 Output On code below to scan and output only the GS1 DataBar code data. Default = GS1 Output Off.
Page 231 * Off UPC-E0 Addenda Required When Required is scanned, the scanner will only read UPC-E bar codes that have addenda. Default = Not Required. Required * Not Required Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-E0 Addenda...
Page 232 UPC-E0 Check Digit Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On UPC-E0 Leading Zero This feature allows the transmission of a leading zero (0) at the beginning of scanned data.
Page 233: Upc-E1
UPC-E1 Most U.P.C. bar codes lead with the 0 number system. For these codes, use UPC-E0 (page 210). If you need to read codes that lead with the 1 number system, use the UPC-E1 On selection. Default = Off. UPC-E1 On * UPC-E1 Off EAN/JAN-13 <Default All EAN/JAN Settings>...
Page 234 EAN/JAN-13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit Addenda.
Page 235: Isbn Translate
Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-E0 Addenda Required.
Page 236: Ean/Jan-8
EAN/JAN-8 <Default All EAN/JAN-8 Settings> EAN/JAN-8 On/Off * On EAN/JAN-8 Check Digit This selection allows you to specify whether or not the check digit should be trans- mitted at the end of the scanned data. Default = On. * On EAN/JAN-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data.
Page 237 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-8 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-8 bar codes that have addenda. Default = Not Required. Required * Not Required Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-E0 Addenda...
Page 238: Msi
<Default All MSI Settings> MSI On/Off * Off MSI Check Character Different types of check characters are used with MSI bar codes. You can program the scanner to read MSI bar codes with Type 10 check characters. Default = Validate Type 10, but Don’t Transmit. When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI bar codes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned data.
Page 239 Validate 2 Type 10 Characters, but Don’t Transmit Validate 2 Type 10 Characters and Transmit Validate Type 11 then Type 10 Character, but Don’t Transmit Validate Type 11 then Type 10 Character and Transmit Disable MSI Check Characters MSI Message Length Scan the bar codes below to change the message length.
Page 240: Gs1 Databar Omnidirectional
GS1 DataBar Omnidirectional < Default All GS1 DataBar Omnidirectional Settings > GS1 DataBar Omnidirectional On/Off * On GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited On/Off * On Xenon/Granit User Guide...
Page 241: Gs1 Databar Expanded
GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off * On GS1 DataBar Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 188) for additional information. Minimum and Maximum lengths = 4-74.
Page 242: Codablock A
Codablock A <Default All Codablock A Settings> Codablock A On/Off * Off If you are reading Code 39 bar codes, Codablock A should remain disabled. If you are enabling Codablock A, you should disable Code 39 (see Code 39 on page 191). Codablock A Message Length Scan the bar codes below to change the message length.
Page 243: Codablock F
Codablock F <Default All Codablock F Settings> Codablock F On/Off * Off If you are reading Code 128 bar codes, Codablock F should remain disabled. If you are enabling Codablock F, you should disable Code 128 (see Code 128 on page 202).
Page 244: Pdf417
*Off PDF417 < Default All PDF417 Settings > PDF417 On/Off * On PDF417 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 188) for additional information. Minimum and Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750. Minimum Message Length Maximum Message Length Xenon/Granit User Guide...
Page 245: Macropdf417
MacroPDF417 MacroPDF417 is an implementation of PDF417 capable of encoding very large amounts of data into multiple PDF417 bar codes. When this selection is enabled, these multiple bar codes are assembled into a single data string. Default = On. * On MicroPDF417 <...
Page 246: Gs1 Composite Codes
Maximum Message Length GS1 Composite Codes Linear codes are combined with a unique 2D composite component to form a new class called GS1 Composite symbology. GS1 Composite symbologies allow for the co-existence of symbologies already in use. Default = Off. * Off UPC/EAN Version Scan the UPC/EAN Version On bar code to decode GS1 Composite symbols that...
Page 247: Gs1 Emulation
Maximum Message Length GS1 Emulation The scanner can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, ITF-14, GS1- 128, and GS1-128 DataBar and GS1 Composites.
Page 248: Tcif Linked Code 39 (Tlc39)
TCIF Linked Code 39 (TLC39) This code is a composite code since it has a Code 39 linear component and a MicroPDF417 stacked code component. All bar code readers are capable of read- ing the Code 39 linear component. The MicroPDF417 component can only be decoded if TLC39 On is selected.
Page 249 Maximum Message Length QR Code Append This function allows the scanner to append the data from several QR Code bar codes together before transmitting them to the host computer. When the scanner encounters an QR Code bar code with the append trigger character(s), it buffers the number of QR Code bar codes determined by information encoded in those bar codes.
Page 250: Data Matrix
Data Matrix < Default All Data Matrix Settings > Data Matrix On/Off * On Data Matrix Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 188) for additional information. Minimum and Maximum lengths = 1-3116.
Page 251: Maxicode
MaxiCode < Default All MaxiCode Settings > MaxiCode On/Off * Off MaxiCode Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 188) for additional information. Minimum and Maximum lengths = 1-150. Minimum Default = 1, Maximum Default = 150. Minimum Message Length Maximum Message Length Xenon/Granit User Guide...
Page 252: Aztec Code
Aztec Code < Default All Aztec Code Settings > Aztec Code On/Off * On Aztec Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 188) for additional information. Minimum and Maximum lengths = 1-3832.
Page 253: Chinese Sensible (Han Xin) Code
Aztec Code Page Aztec Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting.
Page 254: Postal Codes - 2D
Han Xin Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 188) for additional information. Minimum and Maximum lengths = 1-7833. Minimum Default = 1, Maximum Default = 7833. Minimum Message Length Maximum Message Length Postal Codes - 2D The following lists the possible 2D postal codes, and 2D postal code combinations...
Page 255 Japanese Post On KIX Post On Planet Code On Also see Planet Code Check Digit, page 237. Postal-4i On Postnet On Postnet On Also see Postnet Check Digit, page 238. Postnet with B and B’ Fields On InfoMail On Combination 2D Postal Codes: InfoMail and British Post On Intelligent Mail Bar Code and...
Page 256 Postnet and Postal-4i On Postnet and Intelligent Mail Bar Code On Postal-4i and Intelligent Mail Bar Code On Postal-4i and Postnet with B and B’ Fields On Planet Code and Postnet On Planet Code and Postnet with B and B’ Fields On Planet Code and Postal-4i On Planet Code and...
Page 257: Planet Code Check Digit
Planet Code, Postal-4i, and Intelligent Mail Bar Code On Postnet, Postal-4i, and Intelligent Mail Bar Code On Planet Code, Postal-4i, and Postnet with B and B’ Fields On Planet Code, Intelligent Mail Bar Code, and Postnet with B and B’ Fields On Postal-4i, Intelligent Mail Bar Code, and Postnet with B and B’...
Page 258: Postnet Check Digit
* Don’t Transmit Check Digit Postnet Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of Postnet data. Default = Don’t Transmit. Transmit Check Digit * Don’t Transmit Check Digit Australian Post Interpretation This option controls what interpretation is applied to customer fields in Australian 4-State symbols.
Page 259: Postal Codes - Linear
Combination C and N Tables Postal Codes - Linear The following lists linear postal codes. Any combination of linear postal code selec- tions can be active at a time. China Post (Hong Kong 2 of 5) <Default All China Post (Hong Kong 2 of 5) Settings> China Post (Hong Kong 2 of 5) On/Off * Off China Post (Hong Kong 2 of 5) Message Length...
Page 260: Korea Post
Korea Post <Default All Korea Post Settings> Korea Post * Off Korea Post Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 188) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length Korea Post Check Digit...
Page 261: Chapter 11 - Imaging Commands
CHAPTER IMAGING COMMANDS The scanner is like a digital camera in the way it captures, manipulates, and trans- fers images. The following commands allow you to alter the way the scanner per- forms these functions. Note: If you are using the scanner in a stand, you must set the In-Stand Sensor Mode to Off in order to take images (see In-Stand Sensor Mode on page 124).
Page 262: Image Snap - Imgsnp
Image Ship - IMGSHP (page 245) Intelligent Signature Capture - IMGBOX (page 255) The modifiers for each of these commands follow the command description. Note: The images included with each command description are examples only. The results you achieve may be different from those included in this manual. The quality of the output you receive will vary depending on lighting, quality of the initial image/object being captured, and distance of the scanner from the image/object.
Page 263 B - Beeper Causes a beep to sound after an image is snapped. No beep (default) Sounds a beep when the image is captured. T - Wait for Trigger Waits for a hardware trigger press before taking the image. This is only available when using Photo Style (1P).
Page 264 G - Gain Gain is used in Manual Style only (2P). Like a volume control, the gain modifier boosts the signal and multiplies the pixel value. As you increase the gain, the noise in an image is also amplified. No gain (default) Medium gain Heavy gain Maximum gain...
Page 265: Image Ship - Imgshp
U - Update Tries This sets the maximum number of frames the scanner should take to reach the Delta for Acceptance. Update Tries is only available when using Photo Style (1P). (Default = 6) Range: 0 - 10 % - Target Set Point Percentage Sets the target point for the light and dark values in the captured image.
Page 266: Imgshp Modifiers
IMGSHP Modifiers A - Infinity Filter Enhances pictures taken from very long distances (greater than 10 feet or 3m). The Infinity Filter should not be used with IMGSNP Modifiers (page 242). Infinity filter off (default) Infinity filter on Example: Infinity Filter off (0A) nfinity Filter on (1A) from approximately 12 feet from approximately 12 feet (3.66m)
Page 267 E - Edge Sharpen An edge sharpen filter cleans up the edges of an image, making it look cleaner and sharper. While edge sharpening does make the image look cleaner, it also removes some fine detail from the original image. The strength of the edge sharpen filter can be entered from 1 to 24.
Page 268 F - File Format Indicates the desired format for the image. KIM format TIFF binary TIFF binary group 4, compressed TIFF grayscale Uncompressed binary (upper left to lower right, 1 pixel/bit, 0 padded end of line) Uncompressed grayscale (upper left to lower right, bitmap format) JPEG image (default) BMP format (lower right to upper left, uncompressed) TIFF color compressed image...
Page 269 I - Invert Image Invert image is used to rotate the image around the X or Y axis. Invert around the X axis (flips picture upside down) Invert around the Y axis (flips picture left to right) Example: Image not inverted: Image with Invert Image with Invert Image set to 1ix:...
Page 270 IR - Image Rotate Image as snapped (rightside up) (default) Rotate image 90 degrees to the right Rotate image 180 degrees (upside down) Rotate image 90 degrees to the left Example: Image Rotate set to 2ir: Image Rotate set to 0ir: Image Rotate set to 1ir: Image Rotate set to 3ir: J - JPEG Image Quality...
Page 271 K - Gamma Correction Gamma measures the brightness of midtone values produced by the image. You can brighten or darken an image using gamma correction. A higher gamma correc- tion yields an overall brighter image. The lower the setting, the darker the image. The optimal setting for text images is 50K.
Page 272 The bottom edge of the shipped image corresponds to row n - 1 of the image in memory. Range: 000 - 639. (Default = all rows) Example: Uncropped Image: Image Crop set to Image Crop set to 300R: 300L: Image Crop set to 200B: Image Crop set to 200T: Alternately, specify the number of pixels to cut from the outside margin of the image;...
Page 273 The smaller number of pixels shipped, the smaller the image, however, after a cer- tain point the image becomes unusable. ship every pixel (default) ship every 2nd pixel, both horizontally and vertically ship every 3rd pixel, both horizontally and vertically Pixel Ship Pixel Ship Pixel Ship set to 1S:...
Page 274: Image Size Compatibility
V - Blur Image Smooths transitions by averaging the pixels next to the hard edges of defined lines and shaded areas in an image. Don’t blur (default) Blur Example: Blur Image Off (0V): Blur Image On (1V): W - Histogram Ship A histogram gives a quick picture of the tonal range of an image, or key type.
Page 275: Intelligent Signature Capture - Imgbox
* Native Resolution Intelligent Signature Capture - IMGBOX IMGBOX allows you to configure the size and location of a signature capture area relative to its proximity to a bar code. This allows you to tailor a signature capture area to a specific form. In order to use IMGBOX, you need a set form where the sig- nature box location is in a known location relative to a bar code.
Page 276: Imgbox Modifiers
To see this example, align the aimer with the signature area (not with the bar code), then press the trigger. Send the following IMGBOX command string after the trigger press: Example: IMGBOX245w37h55y. Note: Case is not important in the command string. It is used here only for clarity. The following image is captured: The IMGBOX commands have many different modifiers that can be used to change the size and appearance of the signature image output by the scanner.
Page 277 B - Output Image Height This option is used to size the image vertically. If using this option, set the resolu- tion (R) to zero. Example: Image Height set to 50B: Image Height set to 100B: D - Pixel Depth This indicates the number of bits per pixel in the transmitted image, which defines whether it will be grayscale or black and white.
Page 278 H - Height of Signature Capture Area The height of the signature capture area must be measured in inches divided by .01. In the example, the height of the area to be captured is 3/8 inch, resulting in a value of H = .375/0.01 = 37.5. Example: IMGBOX245w37h55y.
Page 279 decimal point between the first and second digit. For example, use 2500 to specify a resolution of 2.5. Set to zero when using the A and B modifiers (see A - Output Image Width B - Output Image Height on page 257). Example: Resolution set to 0R: Resolution set to 1000R:...
Page 280: Rf Default Imaging Device
Y - Vertical Bar Code Offset The vertical bar code offset allows you to offset the vertical center of the signature capture area. Negative numbers indicate that the signature capture is above the bar code, and positive numbers indicate that the area is below the bar code. Mea- surements are in multiples of the minimum bar width Example: Vertical Offset set to -7Y:...
Page 281: Chapter 12 - Utilities
CHAPTER UTILITIES To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts, beginning on page 339) for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D.
Page 282: Show Software Revision
Show Software Revision Scan the bar code below to output the current software revision, unit serial number, and other product information for both the scanner and base. Show Software Revision Test Menu When you scan the Test Menu On code, then scan a programming code in this manual, the scanner displays the content of a programming code.
Page 283: Application Plug-Ins (Apps)
Application Plug-Ins (Apps) Any apps that you are using can be turned off or on by scanning the following bar codes. Apps are stored in groups: Decoding, and Formatting. You can enable and disable these groups of apps by scanning that group’s On or Off bar code below. You can also scan the List Apps bar code to output a list of all your apps.
Page 284: Ezconfig Cloud For Scanning Operations
Imaging also lets you preview the images continuously captured by the scanner. Install EZConfig Cloud for Scanning Use the EZConfig Cloud for Scanning tool to configure your scanner online: 1. Access the Honeywell web site at www.honeywellaidc.com 2. Click on the Browse Products tab. Under Software, select Device Management.
Page 285 If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want to restore the scanner to factory default settings, first scan the Remove Custom Defaults bar code, then scan Activate Defaults. This resets the scanner to the factory default settings. Remove Custom Defaults Activate Defaults Note: If using a cordless system, scanning the Activate Defaults bar code also causes both...
Page 286 Xenon/Granit User Guide...
Page 287: Chapter 13 - Serial Programming Commands
CHAPTER SERIAL PROGRAMMING COMMANDS The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will program the scanner. For complete descriptions and examples of each serial programming command, refer to the corresponding programming bar code in this manual.
Page 288: Query Commands
scanner. This setting is changed by using the BT_NAM command, which accepts alphanumeric values. If the name is not known, a wildcard (*) can be used :* Note: Since the base stores all work group settings and transfers to them to scanner once they are linked, changes are typically done to the base and not to the scanner.
Page 289 SubTag Field Usage When a query is used in place of a SubTag field, the query applies only to the sub- set of commands available that match the Tag field. In this case, the Data field should not be used because it is ignored by the device. Data Field Usage When a query is used in place of the Data field, the query applies only to the spe- cific command identified by the Tag and SubTag fields.
Page 290: Trigger Commands
This response indicates that Codabar Coding Enable (CBRENA) has a range of val- ues from 0 to 1 (off and on). Example: What is the default value for Codabar Coding Enable? Enter: cbrena^. Response: CBRENA1[ACK] This response indicates that the default setting for Codabar Coding Enable (CBRENA) is 1, or on.
Page 291: Reset The Custom Defaults
The scanner scans until a bar code has been read, until the deactivate command is sent, or until the serial time-out has been reached (see Read Time-Out on page 121 for a description, and the serial command on page 284). Reset the Custom Defaults If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults bar code below.
Page 292: Menu Commands
Menu Commands Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Product Default Settings Set Custom Defaults Set Custom Defaults MNUCDP Save Custom Defaults MNUCDS Reset the Custom Defaults Activate Custom Defaults DEFALT Reset the Factory Defaults - Factory Default Settings: PAPDFT&...
Page 293 # Indicates a numeric Page * Indicates default entry Plug and Play Codes Verifone Ruby Terminal PAPRBY Gilbarco Terminal PAPGLB Honeywell Bioptic Aux Port PAPBIO Datalogic Magellan Aux Port PAPMAG NCR Bioptic Aux Port PAPNCR Wincor Nixdorf Terminal PAPWNX Wincor Nixdorf Beetle...
Page 294 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Greek KBDCTY17 Greek (220 Latin) KBDCTY64 Greek (220) KBDCTY61 Greek (319 Latin) KBDCTY65 Greek (319) KBDCTY62 Greek (Latin) KBDCTY63 Greek (MS) KBDCTY66 Greek (Polytonic) KBDCTY60 Hebrew KBDCTY12 Hungarian (101 key) KBDCTY50 Hungary...
Page 295 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Serbia (Latin) KBDCTY36 Slovakia KBDCTY22 Slovakia (QWERTY) KBDCTY49 Slovakia (QWERTZ) KBDCTY48 Slovenia KBDCTY31 Spain KBDCTY10 Spanish variation KBDCTY51 Sweden KBDCTY23 Switzerland (French) KBDCTY29 Switzerland (German) KBDCTY6 Tatar KBDCTY85 Turkey F KBDCTY27...
Page 296 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Keyboard Modifiers *Control + X Off KBDCAS0 DOS Mode Control + X KBDCAS1 Windows Mode Control + X KBDCAS2 Windows Mode Prefix/Suffix Off KBDCAS3 *Turbo Mode Off KBDTMD0 Turbo Mode On KBDTMD1...
Page 297 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry RS232 Handshaking *RTS/CTS Off 232CTS0 Flow Control, No Timeout 232CTS1 Two-Direction Flow Control 232CTS2 Flow Control with Timeout 232CTS3 RS232 Timeout 232DEL#### *XON/XOFF Off 232XON0 XON/XOFF On 232XON1 *ACK/NAK Off 232ACK0...
Page 298 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Beeper Pitch - Base Error *Razz (250) (min 200Hz) BASFQ2250 Medium (3250) BASFQ23250 High (4200) (max 9000Hz) BASFQ24200 Number of Beeps - Base Error BASERR3 Range 1 - 9 BASERR# Scanner Report Scanner Report...
Page 299 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Batch Mode Quantity *Off BATQTY0 BATQTY1 Quantity Codes BATNUM0 BATNUM1 BATNUM2 BATNUM3 BATNUM4 BATNUM5 BATNUM6 BATNUM7 BATNUM8 BATNUM9 Batch Mode Output Order *FIFO BATLIF0 LIFO BATLIF1 Total Records Total Records BATNRC Delete Last Code...
Page 300 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Bluetooth HID Keyboard PAPSPP Disconnect Bluetooth Serial Port - PCs/ BT_TRM0;BT_DNG5 Laptops BT Connection - PDA/Mobility BT_TRM0;BT_DNG1 Systems Device Bluetooth PIN Code BT_PIN Auto Reconnect Mode *Auto Reconnect On BT_ACM1 Auto Reconnect Off BT_ACM0...
Page 301 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Scan While in Base Cradle Scan in Cradle Off BT_SIC0 *Scan in Cradle On BT_SIC1 Shut Down Scanner in Cradle BT_SIC2 Base Charge Modes Base Charge Off BASCHG0 *External or Interface Cable Power BASCHG1...
Page 302 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Scanner Power Time-Out Timer Timer (0-7200 seconds) BT_LPT0 200 Seconds BT_LPT200 *400 Seconds BT_LPT400 900 Seconds BT_LPT900 3600 Seconds BT_LPT3600 7200 Seconds BT_LPT7200 Flexible Power Management Full Power BT_TXP8 *Medium High Power BT_TXP7...
Page 303 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Batch Mode Transmit Delay *Off BATDLY0 Short (ms) BATDLY250 Medium (ms) BATDLY500 Long (ms) BATDLY1000 Scanner Name Name 1-7 BT_NAM##### Reset RESET_ Scanner Name BT_NAM Bluetooth Connection Bluetooth PIN Code BT_PIN Auto Reconnect Mode...
Page 304 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Vibrate Duration Duration TFBDUR#### (100 - 2,000 ms) *100- Granit1910i1D/1911i1D *300-all other scanners Beeper Pitch - Error (Frequency) *Razz (250) (min 200Hz) BEPFQ2800 Medium (3250) BEPFQ23250 High (4200) (max 9000Hz) BEPFQ24200 Beeper Duration - Good Read *Normal Beep...
Page 305 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Presentation LED Behavior After *LEDs On TRGPCK1 Decode LEDs Off TRGPCK0 Presentation Sensitivity (not Range 0-20 (*1) TRGPMS## supported by Granit 1980i and 1981i) Presentation Centering Window Presentation Centering On PDCWIN1 *Presentation Centering Off...
Page 306 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry 2D Reread Delay *2D Reread Delay Off DLY2RR0 Short (1000ms) DLY2RR1000 Medium (2000ms) DLY2RR2000 Long (3000ms) DLY2RR3000 Extra Long (4000ms) DLY2RR4000 Character Activation Mode *Off HSTCEN0 HSTCEN1 Activation Character (Range 0- HSTACH### 255) *12 [DC2]...
Page 307 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Preferred Symbology PRFENA1 *Off PRFENA0 High Priority Symbology PRFCOD## Low Priority Symbology PRFBLK## Preferred Symbology Timeout PRFPTO#### (*500) Range 100-3000 Preferred Symbology Default PRFDFT Output Sequence Editor Enter Output Sequence SEQBLK Add Prefix to Complete Output...
Page 308 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Video Reverse Video Reverse Only VIDREV1 Video Reverse and Standard Bar VIDREV2 Codes *Video Reverse Off VIDREV0 Working Orientation *Upright ROTATN0 Vertical, Bottom to Top (Rotate ROTATN1 CCW 90°) Upside Down ROTATN2...
Page 309 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry LED Flash Rate *Fast Flash BEPLFR50 Medium Flash BEPLFR250 Slow Flash BEPLFR500 LED Solid (No Flash) *LED Solid Off (Resume Flash) BEPLOT0 LED Solid 1 Second BEPLOT1 LED Solid 3 Seconds BEPLOT3 LED Solid 5 Seconds...
Page 310 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Low Contrast Data Matrix * Low Contrast Data Matrix DEPMENA1 Enhancements Enhancements On Low Contrast Data Matrix DPMENA0 Enhancements Off Prefix/Suffix Selections Add CR Suffix to All Symbologies VSUFCR Prefix Add Prefix...
Page 311 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Primary/Alternate Data Formats Primary Data Format ALTFNM0 Data Format 1 ALTFNM1 Data Format 2 ALTFNM2 Data Format 3 ALTFNM3 Single Scan Data Format Change Single Scan-Primary VSAF_0 Data Format Single Scan-Data Format 1 VSAF_1...
Page 312 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Code 39 Append *Off C39APP0 C39APP1 Code 32 Pharmaceutical (PARAF) *Off C39B320 C39B321 Code 39 Full ASCII *Off C39ASC0 C39ASC1 Code 39 Code Page C39DCP Interleaved 2 of 5 Default All Interleaved I25DFT 2 of 5 Settings...
Page 313 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Straight 2 of 5 Industrial Default All Straight 2 of 5 R25DFT Industrial Settings *Off R25ENA0 R25ENA1 Straight 2 of 5 Industrial Message Minimum (1 - 48) *4 R25MIN## Length Maximum (1 - 48) *48...
Page 314 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry GS1-128 Default All GS1-128 Settings GS1DFT GS1ENA1 GS1ENA0 GS1-128 Message Length Minimum (1 - 80) *1 GS1MIN## Maximum (0 - 80) *80 GS1MAX## Telepen Default All Telepen TELDFT Settings *Off...
Page 315 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry UPC-E0 Default All UPC-E UPEDFT Settings UPEEN00 UPEEN01 UPC-E0 Expand *Off UPEEXP0 UPEEXP1 UPC-E0 Addenda Required Required UPEARQ1 *Not Required UPEARQ0 Addenda Timeout Range (0 - 120) *500 DLYADD##### UPC-E0 Addenda Separator UPEADS1...
Page 316 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry ISBN Translate *Off E13ISB0 E13ISB1 EAN/JAN-8 Default All EAN/ EA8DFT JAN 8 Settings EA8ENA0 EA8ENA1 EAN/JAN-8 Check Digit EA8CKX0 EA8CKX1 EAN/JAN-8 Addenda *2 Digit Addenda Off EA8AD20 2 Digit Addenda On EA8AD21 *5 Digit Addenda Off...
Page 317 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry GS1 DataBar Limited Default All GS1 DataBar Limited RSLDFT Settings RSLENA0 RSLENA1 GS1 DataBar Expanded Default All GS1 DataBar RSEDFT Expanded Settings RSEENA0 RSEENA1 GS1 DataBar Expanded Msg. Minimum (4 - 74) *4 RSEMIN## Length...
Page 318 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry UPC/EAN Version COMUPC1 *Off COMUPC0 GS1 Composite Codes Msg. Length Minimum (1-2435) *1 COMMIN#### Maximum (1-2435) *2435 COMMAX#### GS1 Emulation GS1-128 Emulation EANEMU1 GS1 DataBar Emulation EANEMU2 GS1 Code Expansion Off EANEMU3 EAN8 to EAN13 Conversion...
Page 319 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Aztec Code Page Aztec Code Page (*51) AZTDCP## Chinese Sensible (Han Xin) Code Default All Han Xin Code Settings HX_DFT HX_ENA1 *Off HX_ENA0 Chinese Sensible (Han Xin) Code Minimum (1-7833) *1 HX_MIN#### Msg.
Page 320 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Postnet, Postal-4i, and Intelligent POSTAL24 Mail Bar Code On Planet, Postal-4i, and Postnet with POSTAL25 B and B’ Fields On Planet, Intelligent Mail Bar Code, POSTAL26 and Postnet with B and B’ Fields Postal-4i, Intelligent Mail Bar POSTAL27 Code, and Postnet with B and B’...
Page 321 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry *Imaging Style - Photo SNPSTY1 Imaging Style - Manual SNPSTY2 Beeper On SNPBEP1 *Beeper Off SNPBEP0 *Wait for Trigger Off SNPTRG0 Wait for Trigger On SNPTRG1 *LED State - Off SNPLED0 LED State - On SNPLED1...
Page 322 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Histogram Stretch On IMGHIS1 *Noise Reduction Off IMGFSP0 Noise Reduction On IMGFSP1 Invert Image around X axis IMGNVX1 Invert Image around Y axis IMGNVY1 Rotate Image none IMGROT0 Rotate Image 90°...
Page 323 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Show Software Revision REVINF Test Menu TSTMNU1 *Off TSTMNU0 Application Plug-Ins (Apps) *Decoding Apps On PLGDCE1 Decoding Apps Off PLGDCE0 *Formatting Apps On PLGFOE1 Formatting Apps Off PLGFOE0 List Apps PLGINF...
Page 324 Xenon/Granit User Guide...
Page 325: Chapter 14 - Product Specifications
CHAPTER PRODUCT SPECIFICATIONS Xenon 1900/1900h Corded Scanner Product Specifications Parameter Specification Mechanical Height 6.3 inches (160mm) Length 4.1 inches (104.1mm) Width 2.8 inches (71.1mm) Weight 5.2 ounces (147.42g) Electrical Voltage Requirements 4 - 5.5 VDC at input connector Current Draw @5VDC ScanningStandby B&W 470mA, 2.35W90mA, .45W...
Page 326: Xenon 1902/1902H/1912 Cordless Scanner Product Specifications
Parameter (Continued) Specification Humidity 0 to 95% non-condensing Mechanical Drop Operational after 50 drops from 6 feet (1.83m) to concrete at 23°C Vibration Withstands 5G peak from 22 to 300 Hz ESD Tolerance Up to 15kV direct air Up to 8 kV indirect coupling plane Image Image Size 838 x 640 pixels...
Page 327 Parameter (Continued) Specification Expected Hours of Operation Expected Charge Time 4.5 hours Radio Frequency 2.4 to 2.5 GHz (ISM Band) Frequency Hopping Bluetooth v.2.1 Range 33 ft. (10 m) typical Data Rate Up to 1 MBps Environmental Temperature Ranges: Operating 32...
Page 328: Xenon 1902G-Bf Scanner Product Specifications
Xenon 1902g-BF Scanner Product Specifications Parameter Specification Mechanical Height 6.3 inches (160mm) Length 4.1 inches (104.1mm) Width 2.8 inches (71.1mm) Weight 6.9 ounces (195g) Electrical Illumination LED: Peak Wavelength 624nm + 18nm (red LED) IEC 62471: “Exempt Risk Group” 442nm, 552nm (white LED) IEC 62471: “Exempt Risk Group”...
Page 329: Granit 1910I Industrial Corded Scanner Product Specifications
Parameter (Continued) Specification Motion Tolerance: Up to 240 inches per second for 13 mil UPC Symbol Contrast Grade 1.0 (20% or greater) Granit 1910i Industrial Corded Scanner Product Specifications Parameter Specification Mechanical Height 7.7 in. (195.6mm) Length 5.2 in. (132.1mm) Width 2.9 in.
Page 330: Granit 1911I Industrial Cordless Scanner Product Specifications
Parameter (Continued) Specification Scan Performance Skew Angle +65° Pitch Angle +45° Motion Tolerance: Streaming Presentation Trigger: 240 inches per second at 6.5 in. (16.5cm) 13 mil UPC 150 inches per second at 10 in. (25.4cm) Symbol Contrast Grade 1.0 (20% or greater) Granit 1911i Industrial Cordless Scanner Product Specifications Parameter...
Page 331: Granit 1980I Industrial Full Range Corded Scanner Product Specifications
Parameter (Continued) Specification Environmental Temperature Ranges: Operating while not charging -4F to + 122F (-20C to 50C) Operating while charging 41F to + 104F (5C to 40C) Storage with battery* -4F to +95F (-20C to 35C) for storage up to 90 days -4F to +68F (-20C to 20C) for storage up to 365 days...
Page 332: Granit 1981I Industrial Full Range Cordless Scanner Product Specifications
Parameter (Continued) Specification Current Draw @5VDC ScanningStandby 470mA, 2.35W100mA, 0.5W Power Supply Noise Rejection Maximum 100mV peak to peak, 10 to 100 kHz Illumination LED: Peak Wavelength 617nm + 18nm (amber LED) IEC 62471: “Exempt Risk Group” Aiming: Peak Wavelength Laser 650nm IEC 60825-1: “Class 2”...
Page 333 Parameter (Continued) Specification Weight 14.8 oz. (420g) Electrical Illumination LED: Peak Wavelength 617nm + 18nm (amber LED) IEC 62471: “Exempt Risk Group” Aiming: Peak Wavelength Laser 650nm IEC 60825-1: “Class 2” Optical Power Laser <1mW Battery Battery: Lithium Ion 2400 mAHr minimum Number of Scans at least 7200 scans (1 scan every 4 seconds for 8 hours)
Page 334: Granit 1920I Industrial Dpm Scanner Product Specifications
Parameter (Continued) Specification Pitch Angle +70° typical, 200 lux, EAN/UPC Motion Tolerance: 30 inches per second typical on 13 mil UPC/EAN bar code 8 in. from scanner nose Symbol Contrast 1D codes 30% or greater (typical, 200 lux, 13 mil) 2D codes 40% or greater (typical, 200 lux, 20 mil) *Storage outside of this temperature range could be detrimental to battery life.
Page 335: Ccb01-010Bt Charge Base Product Specifications
Parameter (Continued) Specification Image Image Size 844 x 640 pixels Scan Performance 1D Skew Angle +65° 2D Skew Angle +45° Pitch Angle +45° Motion Tolerance: Enhanced Streaming Presentation 138 in. per second at 2.8 in. Trigger for 13 mil UPC (3500 mm per second at 70mm) Symbol Contrast CCB01-010BT Charge Base Product Specifications...
Page 336: Ccb01-010Bt-07N-Bf Charge Base Product Specifications
Parameter (Continued) Specification ESD Sensitivity Up to 15kV direct air Up to 8 kV indirect coupling plane CCB01-010BT-07N-BF Charge Base Product Specifications Parameter Specification Mechanical Height 3.2 inches (81.3mm) Length 5.19 inches (131.8mm) Width 3.98 inches (101.1mm) Weight 6.3 oz (179g) Electrical Voltage: 4.5 to 5.5 volts...
Page 337: Ccb02-100Bt/Ccb05-100Bt Industrial Charge Base Product Specifications
CCB02-100BT/CCB05-100BT Industrial Charge Base Product Specifications Parameter Specification Mechanical Height 2.6 in. (66mm) Length 9.8 in. (248.9mm) Width 4.05 in. (102.9cm) Weight 10.05 oz. (285g) Electrical Voltage: 4.5 to 5.5 volts Current Draw: Host Terminal Port 500mA Aux Power Port Charge Time 5 hours Radio...
Page 338: Depth Of Field Charts
Depth of Field Charts Xenon B&W Scanner Typical Performance Focus High Density (HD) Standard Range (SR) Extended Range (ER) Near Near Near Symbology Distance Distance Distance Distance Distance Distance 5 mil Code 39 96.5 40.6 134.6 203.2 13 mil UPC 16.7 20.7 12.7...
Page 339: Xenon B&W Scanner Guaranteed Performance
Xenon B&W Scanner Guaranteed Performance Focus High Density (HD) Standard Range (SR) Extended Range (ER) Near Near Near Symbology Distance Distance Distance Distance Distance Distance 5 mil Code 39 7.62 83.8 53.3 129.5 106.7 198.1 13 mil UPC 15.6 19.7 17.8 154.9 10.2...
Page 340 Xenon Color Scanner (Model COL) Guaranteed Performance Focus High Density (HD) Standard Range (SR) Near Near Symbology Far Distance Far Distance Distance Distance 5 mil Code 39 83.8 43.2 124.5 13 mil UPC 14.5 15.2 132.1 10.2 368.3 20 mil Code 39 17.5 12.7 12.7...
Page 341 Granit 1910i/1911i Scanner Guaranteed Performance Focus Extended Range (ER) Symbology Near Distance Far Distance 5 mil Code 39 96.5 182.9 20 mil Code 39 28.7 25.4 100% UPC 21.7 15.2 551.2 6.7 mil PDF417 76.2 215.9 10 mil Data Matrix 78.7 246.4 20 mil QR Code...
Page 342 Focus (Continued) Full Range (FR) Symbology (Continued) Near Distance Far Distance 10 mil Data Matrix 40.3 10.0 102.3 55 mil Data Matrix 16.9 232.8 42.8 591.3 100 mil Data Matrix 31.8 406.5 80.7 1032.5 Resolution (1D Code 39) 2 mil (.051mm) Resolution (2D Data Matrix) 2 mil (.051mm) Granit 1980i/1981i Scanner Guaranteed Performance (200 lux)
Page 343 Granit 1920i Typical Performance Focus Symbology Near Distance Far Distance 3 mil Code 39 5 mil Code 39 100% UPC 5 mil PDF417 5 mil Data Matrix 20 mil QR Code Resolution (1D Code 39) 2.5 mil (0.063mm) Resolution (2D Data Matrix) 4 mil (0.102mm) Granit 1920i Guaranteed Performance Focus...
Page 344 Standard Connector Pinouts Note: The following pin assignments are not compatible with Honeywell legacy products. Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty.
Page 345 RS485 Output 10 Pin RJ41 Modular Plug - connects to the base Note: RS485 signal conversion is performed in the cable. 1Cable shield 2Cable select 3Supply ground 4Transmit data 5Receive data - serial data to scanner 7+5V power 8Transmit Enable 10 Pin Modular Plug - connects to the base 1Cable shield 2Cable select...
Page 346 Required Safety Labels Xenon 1900/1902 Scanner LASER LIGHT- DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT. RAYONNEMENT LASER NE PAS REGARDER DANS LE FAISCEAU. APPAREIL À LASER DE CLASSE 2. MAX. 1mW: 630-680 nm IEC 60825-1:2007. Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No.
Page 347 CCB01-010BT/CCB01-010BT-07N-BF Base Part Number, Serial Number and Compliance Label Revision locations Information location Xenon/Granit User Guide...
Page 348 Granit 1910i/1911i/1920i/1980i/1981i Scanner LASER LIGHT- DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT. RAYONNEMENT LASER NE PAS REGARDER DANS LE FAISCEAU. APPAREIL À LASER DE CLASSE 2. MAX. 1mW: 630-680 nm IEC 60825-1:2007. Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No.
Page 349 CCB02-100BT/CCB05-100BT Base Compliance Label locations Xenon/Granit User Guide...
Page 350 Xenon/Granit User Guide...
Page 351 CHAPTER MAINTENANCE AND TROUBLESHOOTING Repairs Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized service center (see Customer Support page xvii). Maintenance Your device provides reliable and efficient operation with a minimum of care. Although specific maintenance is not required, the following periodic checks ensure dependable operation: Clean the Scanner...
Page 352 When properly seated, the connector is held in the scanner’s handle by a flexible retention tab. The interface cable is designed to be field replaceable. • Order replacement cables from Honeywell or from an authorized distributor. • When ordering a replacement cable, specify the cable part number of the original interface cable.
Page 353 Replace a Xenon Interface Cable 1. Turn off the power to the host system. 2. Disconnect the scanner’s cable from the terminal or computer. 3. Locate the small hole on the back of the scanner’s handle. This is the cable release. 4.
Page 354 3. Turn the base upside down. 4. Pull the connector out while maintaining pressure on the connector release clip. CCB02-100BT/CCB05-100BT Base: CCB01-010BT Base: 5. Replace with the new cable. Insert the connector into the opening and press firmly. The connector is keyed to go in only one way, and will click into place.
Page 355 Change a Granit Scanner Battery 1. Twist the tab in the bottom of the end cap and open the hinged battery door. (When new, the bat- tery door may stick. Use pliers to twist the tab and open the door until it loosens up.) 2.
Page 356 If you aren’t sure what programming options have been set in the scanner, or if you want the factory default settings restored, refer to Reset the Factory Defaults page 264. Troubleshoot a Cordless System Troubleshoot a Base Note: Visit the Services and Support section of our website (www.honeywellaidc.com) to check for the latest software for both the scanner and the base.
Page 357 The bar code is displayed on the host device correctly, but you still have to press a key to enter it (the Enter/Return key or the Tab key, for example). • You need to program a suffix. Programming a suffix enables the scanner to output the bar code data plus the key you need (such as “CR”) to enter the data into your application.
Page 358 Xenon/Granit User Guide...
Page 359 Refer to Data Edit beginning on page 161 and Data Format beginning on page 167 for information about using Code ID and AIM ID. Linear Symbologies Honeywell Possible modifiers Symbology All Symbologies Codabar Code 11 Code 128 0, 1, 2, 4 Code 32 Pharmaceutical (PARAF) <...
Page 360 0, 1, 2, 3, 8, 9, A, B, C UPC-A UPC-A with Add-On UPC-A with Extended Coupon Code UPC-E UPC-E with Add-On UPC-E1 Add Honeywell Code ID 5C80 Add AIM Code ID 5C81 Add Backslash 5C5C Batch mode quantity 2D Symbologies...
Page 361 Honeywell Possible modifiers Symbology Chinese Sensible Code (Han Xin Code) Codablock A 0, 1, 4, 5, 6 Codablock F 0, 1, 4, 5, 6 Code 49 0, 1, 2, 4 Data Matrix GS1 Composite GS1 DataBar Omnidirectional MaxiCode PDF417 MicroPDF417...
Page 362 ASCII Conversion Chart (Code Page 1252) In keyboard applications, ASCII Control Characters can be represented in 3 differ- ent ways, as shown below. The CTRL+X function is OS and application dependent. The following table lists some commonly used Microsoft functionality. This table applies to U.S.
Page 363 Lower ASCII Reference Table Note: Windows Code page 1252 and lower ASCII use the same characters. Printable Characters Character Character DEC Character <SPACE> " & < > ⌂ Extended ASCII Characters CP 1252 ASCII Alternate Extended PS2 Scan Code ↑ €...
Page 364 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code Œ î Reserved ì Reserved Ž Ä Numeric Keypad Enter 0x1C Å Numeric Keypad / 0x35 É 0x3B ‘ æ 0x3C ’ Æ 0x3D “ ô 0x3E ” ö...
Page 365 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code Â ┬ Ã ├ Ä ─ Å í Æ ╞ Ç ╟ È ╚ É ╔ Ê ╩ Ë ╦ Ì ╠ Í ═ Î ╬ Ï ╧ Ð...
Page 366 (standard ASCII) Automatic National Character ISO/IEC 2022 2 (default) Replacement Binary Code page Default “Automatic National Character replacement” will select the below Honeywell Code Page options for Code128, Code 39 and Code 93. United States ISO/IEC 646-06 Canada ISO /IEC 646-121...
Page 367 Honeywell Code Page Selection Method/ Keyboard Code Standard Country Country Page Option Spain ISO/IEC 646-17 Spain ISO/IEC 646-85 Xenon/Granit User Guide...
Page 368 à â ç ê î ô é ù è û à â ç ê É ô é ù è û ⎯ ¥ ⎯ ¥ £ ˜ £ à ° ç § µ é ù è ¨ § Ä Ö Ü ä...
Page 369 Keyboard Key References 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 4B 50 55 5A 5F 64 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 4C 51 56 5B 60 65 1F 20 21 22 23 24 25 26 27 28 29...
Page 370 Xenon/Granit User Guide...
Page 371 SAMPLE SYMBOLS UPC-A Interleaved 2 of 5 01234567890 0 123456 7890 EAN-13 9 780330 290951 Code 128 Code 39 Code 128 BC321 Codabar A13579B Code 93 Straight 2 of 5 Industrial 123456 123456-9$ Matrix 2 of 5 6543210 RSS-14 PDF417 Car Registration (01) 00123456789012 Code 49...
Page 372 SAMPLE SYMBOLS (CONTINUED) Postnet Data Matrix Zip Code Test Symbol QR Code Numbers MaxiCode Micro PDF417 Test Message Test Message Xenon/Granit User Guide...
Page 373 PROGRAMMING CHART Xenon/Granit User Guide...
Page 374 PROGRAMMING CHART (CONTINUED) Save Discard Reset Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again. Xenon/Granit User Guide...
Page 376 Honeywell 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com ™ Xenon-UG Rev V 7/18...

This manual is also suitable for:

Granit series Xenon 1900 Xenon 1900h Xenon 1902 Xenon 1902h Xenon 1902g-bf ... Show all

Honeywell Xenon Series User Manual

Chapter 1 - Get Started

Chapter 2 - Program the Interface

Chapter 3 - Cordless System Operation

Chapter 4 - Cordless System Operation: Xenon 1902G-BF

Chapter 5 - Input/Output Settings

Chapter 6 - Healthcare Settings

Chapter 7 - Direct Part Mark (DPM) Settings

Quick Links

Related Manuals for Honeywell Xenon Series

Summary of Contents for Honeywell Xenon Series