Siemens SINUMERIK 805 Operating Instructions Manual page 147

5 Operating Sequences
5.3.5 Program control
06.90
iÿ§Mtinc>iur:HHKÿÿ|ja3!l» aW® WWm
i
iiBa»
j
{jnlHi
i
iffffli «Hfll
:
llllllKÿÿlllll
:
A
$SÿSSSWSPWÿ!SH!!9Sÿ!SSÿ®J®
J
::S!¥SJÿR :W!RRÿSS
j
SSWSÿTO
:
i®!8S!ÿR!
;
:?B!BHSK
:
:
*>ttWOC<<««MWC*«<ÿ<WWÿWO«<«CCC$
C«<OOXÿ:OOw\X<WOÿXOOÿÿÿ>XWÿX»OC*OC«ÿÿ:ÿÿ«v>X<OÿC<ÿ>eW>Cÿÿe«ÿ
WOOJQOW
AUTOMATIC
j
oooco
i,Vi> Vi>
>
RESET
V VAVAWy'WAiW»%VAV/«VÿViW1V/iWÿV/AViW,i\S%VA
W.SVAWVVVWVW/AÿMVAWVSVVVVAVVSÿVVVVWVWA*.
»|
>\VVW«AÿVAVWVVAVWÿYAV/WAVhVÿVSVWVV\VWÿVWMVÿVAVAWÿVVWiiVW/WAfSWVVVÿVWVVVVtiVÿÿ
yWVAY/AWbSV
8 ?
*
J
<
VUWÿ\VAW«VAVÿVSVÿWsr»V»%VWWAWAWÿWÿVVAÿVANVAWYAW/AVÿ\WAVtiVVSA\Vÿ
The
status
display is shown irrespective of the menu selected.
Program control SKP
skip block
Program blocks
which are
marked with an oblique in front of the block
number, are ignored
during the processing of the program (e.g. M/100...,').
•!:.!
Program control DRY
dry run
Traversing is carried
out at
the feedrate value entered
in the "dry run feedrate" setting data.
The programmed feedrate in program
blocks G01, G02, G03, G33, G34 and
G35 is no
longer
valid.
The dry run feedrate also
applies instead of the programmed feed per revolution in program
blocks with G95.
Program control
ROV
rapid traverse override
There are
two
possible ways of applying this function:
a)
There
is a common override switch for the feedrate and rapid traverse override.
: The value of the feedrate override switch with an override value
limit of
1
00
%
is valid for the rapid traverse override.
ROV
ROV : Rapid
traverse override is
not
possible.
The override value
of
1
00
%
is stipulated.
There is a
separate
override switch for the rapid traverse override. b)
R
: ROV
The values
set
with the rapid traverse override switch
are active.
: ROV The values
set
with the rapid
traverse override switch are
not
active. The override value of
100
%
is stipulated.
5-30 ®
Siemens AG
1990 All Rights Reserved
6ZB5 410-0EE02
SINUMERIK
805,
SW2
(BA)
i;
»: 1
11
1
1
Li I la*.