Icom ID-51A Advanced Manual page 2

Previous view
INTRODUCTION
About these Advanced Manual (PDF format)
These Advanced Manual describe the details of the ID-51A/E features. This PDF formatted manual provides you
with convenient functions, as follows.
Move to the previously read page.
Click
Previous view
each page, to move back to the previ-
ously read page.
Previous view
15
REPEATER AND DUPLEX OPERATIONS
Duplex operation
Shows the location of keys
When the cursor is moved over a term with a red
The Duplex operation shifts the transmit frequency
underline, a red circle appears around the appro-
up or down from the receive frequency by an offset
priate key(s) on the illustration of the transceiver.
amount.
D Setting the frequency offset
q Push [V/MHz] to select the VFO mode.
w Push [MENU] .
e Push D-pad( ) to select the root item ("DUP/
TONE..."), and then push D-pad(Ent).
D-pad
Example: When the cursor is moved over
(Ent)
( ) [V/MHz]
red circle appears around the ap-
r Push D-pad( ) to select the "Offset Freq," and then
propriate key(s).
push D-pad(Ent).
t Rotate [DIAL] to set the frequency offset to be-
tween 0.000.00 and 59.99500 MHz, and then push
D-pad(Ent). (Setting example: 1.000.00 MHz)
• The selected tuning step in the VFO mode is used when
setting the frequency offset.
• Pushing [V/MHz]
below.
TS* 1 MHz
* The frequency changes according to the preset tuning
Move to the page, if clicked.
steps. (p. 5-8)
y Push [MENU] to exit the [MENU] screen.
(p. 15-5)
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the
To reset to the default value.
United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand, and/or other countries.
Push [QUICK] in step t as described above, then
Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United
push D-pad(Ent) to reset to the default value.
States and/or other countries.
All other products or brands are registered trademarks or trademarks of their respective holders.
NOTE:
• The frequency offset cannot be changed while using
the DR function.
• The Auto repeater function uses the preset frequen
cy offset. Depending on the frequency offset value,
Previous view
15
REPEATER AND DUPLEX OPERATIONS
Duplex operation
The Duplex operation shifts the transmit frequency
up or down from the receive frequency by an offset
amount.
D Setting the frequency offset
q Push [V/MHz]
at the left top on an
w Push [MENU]
e Push D-pad( ) to select the root item ("DUP/
TONE..."), and then push D-pad(Ent).
D-pad
(Ent)
( )
Previous view
r Push D-pad( ) to select the "Offset Freq," and then
push D-pad(Ent).
15
REPEATER AND DUPLEX OPERATIONS t Rotate [DIAL] to set the frequency offset to be-
tween 0.000.00 and 59.99500 MHz, and then push
D-pad(Ent).
• The selected tuning step in the VFO mode is used when
setting the frequency offset.
Duplex operation • Pushing [V/MHz]
below.
TS*
The Duplex operation shifts the transmit frequency
up or down from the receive frequency by an offset
* The frequency changes according to the preset tuning
steps. (p. 5-8)
amount.
y Push [MENU]
D Setting the frequency offset
q Push [V/MHz]
w Push [MENU]
e Push D-pad( ) to select the root item ("DUP/
TONE..."), and then push D-pad(Ent).
D-pad
(Ent)
( )
r Push D-pad( ) to select the "Offset Freq," and then
push D-pad(Ent).
t Rotate [DIAL] to set the frequency offset to be-
To reset to the default value.
tween 0.000.00 and 59.99500 MHz, and then push
in the description, a
Push [QUICK]
D-pad(Ent).
push D-pad(Ent) to reset to the default value.
• The selected tuning step in the VFO mode is used when
setting the frequency offset.
NOTE:
• Pushing [V/MHz]
• The frequency offset cannot be changed while using
below.
the DR function.
TS* 1 MHz
• The Auto repeater function uses the preset frequen
cy offset. Depending on the frequency offset value,
* The frequency changes according to the preset tuning
the off band indication, "OFF," appears on the display
steps. (p. 5-8)
toggles the tuning digit, as shown
when [PTT] is pushed. (p. 15-5)
y Push [MENU]
10 MHz
[DIAL]
To reset to the default value.
Push [QUICK] in step t as described above, then
push D-pad(Ent) to reset to the default value.
NOTE:
• The frequency offset cannot be changed while using
the DR function.
• The Auto repeater function uses the preset frequen
cy offset. Depending on the frequency offset value,
the off band indication, "OFF," appears on the display
when [PTT] is pushed. (p. 15-5)
-
Shows a term description
to select the VFO mode.
When the mouse cursor is moved over a term which
.
is highlighted in yellow, the description of the term is
displayed.
(Setting example: 1.000.00 MHz)
toggles the tuning digit, as shown
1 MHz 10 MHz
Previous view
to exit the [MENU] screen.
15
REPEATER AND DUPLEX OPERATIONS
[DIAL]
to select the VFO mode.
Duplex operation
.
The Duplex operation shifts the transmit frequency
up or down from the receive frequency by an offset
amount.
D Setting the frequency offset
q Push [V/MHz] to select the VFO mode.
w Push [MENU] .
e Push D-pad( ) to select the root item ("DUP/
TONE..."), and then push D-pad(Ent).
D-pad
(Ent)
( )
r Push D-pad( ) to select the "Offset Freq," and then
push D-pad(Ent).
t Rotate [DIAL] to set the frequency offset to be-
tween 0.000.00 and 59.99500 MHz, and then push
D-pad(Ent). (Setting example: 1.000.00 MHz)
• The selected tuning step in the VFO mode is used when
setting the frequency offset.
• Pushing [V/MHz] toggles the tuning digit, as shown
in step t as described above, then
below.
(Setting example: 1.000.00 MHz)
TS* 1 MHz 10 MHz
* The frequency changes according to the preset tuning
steps. (p. 5-8)
y Push [MENU] to exit the [MENU] screen.
toggles the tuning digit, as shown
[DIAL]
10 MHz
to exit the [MENU] screen.
To reset to the default value.
Push [QUICK] in step t as described above, then
[DIAL]
push D-pad(Ent) to reset to the default value.
NOTE:
• The frequency offset cannot be changed while using
the DR function.
• The Auto repeater function uses the preset frequen
cy offset. Depending on the frequency offset value,
the off band indication, "OFF," appears on the display
when [PTT] is pushed. (p. 15-5)
The screen shots at the right column, correspond
to the operating instructions and procedures
shows both setting and operating example.
i
The current frequency
offset
Rotate [DIAL], then
push D-pad(Ent).
-
The current frequency
offset
Push [QUICK]
Rotate [DIAL], then
push D-pad(Ent).
Push D-pad(Ent)
- 15-4
The current frequency
offset
15-4
Push [QUICK]
-
Push D-pad(Ent)
The current frequency
offset
Rotate [DIAL], then
push D-pad(Ent).
Push [QUICK]
The current freque
offset
Push D-pad(Ent)
Rotate [DIAL], the
push D-pad(Ent).
The current frequency
offset
Push [QUICK]
Push D-pad(Ent)