Panasonic AJ-HPX2000 Operating Instructions Manual page 37

Shooting procedures when INTERVAL REC is ON
1
Following basic operations of shooting and recording
according to " Basic Procedures ", lock the camera
securely.
2
Check that "i" is blinking in the display, and that the
interval recording mode is selected.
3
Press either REC START/STOP button, REC button on
the handle, or VTR button at the lens.
Interval recording starts. Recording automatically stops
after the specified TAKE TOTAL TIME, and the entire
recording is generated as one clip.
"i" starts blinking in the display when the internal
recording mode is selected. "iREC" illuminates after
recording starts. "iREC" blinks during a pause.
The display in the viewfinder is the same as that in the
display window.
The tally lamp illuminates during recording. If PAUSE
TIME is set at 2 minutes or longer, the tally lamp
illuminates at 5-second intervals to indicate that it is
paused. The tally lamp also blinks 3 seconds before
recording starts.
Time Axis
iREC start
t1 t1
Real-time video
1 2
Sound
t2 t2
TAKE TOTAL TIME
(Time necessary for shooting)
Content on P2 card
1 2 3
TOTAL REC TIME
(Recording time on P2 card)
For continuous recording
Press either the REC START/STOP button, REC button on
the handle, or VTR button at the lens, again. Interval
recording resumes.
To stop recording
Press the STOP button. Recording stops. Then, the camera
accesses the P2 card to record the video stored in memory
before recording stops. The record from the beginning of the
interval recording to the moment of pressing the STOP
button is generated as one clip.
To stop the Interval recording mode
Setting the menu option INTERVAL REC MODE to "OFF".
When INTERVAL REC HOLD is set to [OFF], the mode
returns to ordinary recording mode if the POWER switch of
the unit is turned OFF.
If INTERVAL REC HOLD is set to [ON], the interval record-
ing mode will not change even if the POWER switch is
turned OFF.
REC TIME
(Recording
t1 t1 t1
time=t1)
3 N-1 N
PAUSE TIME
(Recording
t2
time=t2)
N-1
N
One clip
Shooting procedures for the ONE SHOT mode of
INTERVAL REC
After setting the INTERVAL REC mode, follow these steps:
1
Following basic operations of shooting and recording
according to " Basic Procedures ", lock the camera
securely.
2
Press either the REC START/STOP button, REC
button on the handle, or VTR button at the lens.
The AJ-HPX2000 automatically goes into ONE SHOT
pause mode after the specified REC TIME.
3
Performs recording for the duration specified under
the REC TIME option by pressing either the REC
START/STOP button, REC button on the handle, or
VTR button at the lens, and returns to ONE SHOT
pause mode.
4
Press the STOP button.
The video and sound stored in memory are generated
as one clip.
iREC
Time
start
Axis
Real-time video
A
Sound
t
Previous clip
Content on P2 card
One clip
To check the previous recording during a pause
Press the RET button at the lens to put the AJ-HPX2000 into
REC REVIEW mode. ONE SHOT operation continues after
the REC REVIEW.
To divide clips or to change the P2 card used for
recording
Even during ONE SHOT mode, clips will not be generated
on the P2 card until the STOP button is pressed. Press the
STOP button, and stop ONE SHOT mode operation.
To stop the ONE SHOT mode of INTERVAL REC
Set the menu option INTERVAL REC MODE to "OFF".
When INTERVAL REC HOLD is set to [OFF], the mode
returns to ordinary recording mode if the POWER switch of
the unit is turned OFF.
If INTERVAL REC HOLD is set to [ON], the interval record-
ing mode will not change even if the POWER switch is
turned OFF.
Recording and Playback ：Interval Recording
iREC STOP
start button
B
t
REC TIME
A B
(Recording
time=t)
37