Warning And Error Display For Thumbnail Operation And Usb Host Mode - Panasonic AJ-HPX2000 Operating Instructions Manual

Card Warning Code
Code No. Description
The directory organization on the inserted P2
card does not comply with the standards. ([DIR
E-70
NG CARD (Slot No.)] is indicated on the
viewfinder.)
A P2 card was inserted where the number of
rewrites exceeds the limit of the standards.
E-71
([RUN DOWN CARD (Slot No.)] is indicated on
the viewfinder.)

Warning and Error Display for Thumbnail Operation and USB HOST MODE

Item Message
CANNOT ACCESS!
WRITE
PROTECTED!
CARD FULL!
NO CARD!
NO FILE!
CANNOT COPY!
CANNOT DELETE !
UNKNOWN
CONTENTS
FORMAT!
CANNOT FORMAT!
CANNOT REPAIR!
CANNOT RE-
CONNECT!
INVALID VALUE!
UNKNOWN DATA!
Thumbnails
CANNOT REPAIR IN
SELECTION!
NO SD CARD!
NO COPY TO SAME
CARD!
SAME CLIP IS
SELECTED!
USER CLIP NAME
MODIFIED!
TOO MANY CLIPS!
LACK OF REC
CAPACITY!
CANNOT CHANGE!
MISSING CLIP!
Although different kinds of recording
operations will function, data may not be
recorded properly. Use the unit to format the
card immediately.
Although different kinds of recording
operations will function, data may not be
recorded properly. It is recommended to
replace it.
Description
Data cannot be accessed because it is
corrupted or for other reasons.
The P2 or SD card is write protected.
The P2 or SD card is full.
No P2 or SD card is inserted.
The designated file is not found.
Images cannot be copied.
Contents version mismatch prevents
deletion.
Warning displayed to indicate contents
version mismatch.
P2 card problem prevents formatting.
Data cannot be repaired since content that
cannot be repaired is selected.
A clip that does not span multiple P2 cards
cannot be reconnected.
Entered data was invalid.
The metadata character code is invalid.
Some of the selected clip could not be
repaired.
No SD card is inserted.
A clip cannot be copied to the card storing
the original clip.
The clip cannot be copied because a clip that
has already been copied and the original clip
have been selected.
Characters in the clip name had to be
deleted in adding the counter value.
Too many clips are selected.
There is not enough recording capacity left
on the card.
Any thumbnails that cannot be produced on
the AVC-Intra 100 or AVC-Intra 50 and
displayed in gray cannot be changed at the
text memo position.
A shot mark will be added to the clips recorded
on multiple P2 cards when all P2 cards are not
inserted yet.
Recording
A warning code blinks once
every 2 seconds on the time
code display section of the
display window.
Measure
Restore media and clips to normal state before
access.
Insert write-enabled media.
Insert media with sufficient capacity.
Insert compatible media.
Check the file.
Check the conditions for copying.
Match devices and contents version.
Match devices and contents version.
Check P2 card.
Check selected content.
Check selected content.
Enter data in a valid range.
Use UTF-8 for the metadata character code. Use
the viewer to enter correct characters.
Insert an SD card.
Copy the selected clip to a card that does not
contain the original clip.
Confirm the selected clip and release either the
source clip or the destination clip and then execute
the copy operation.
The user clip name plus the counter value can only
contain up to 100 bytes. Characters in the clip
name are automatically deleted when the total
exceeds 100 bytes.
Reduce the number of selected clips.
Insert a card with sufficient recording capacity.
Install the AVC-Intra codec board (AJ-YBX200G,
optional) and set SYSTEM MODE according to the
clips.
Insert all P2 cards with recorded clips, and confirm
that the incomplete clip indicators disappear, and
then add shot marks.
Maintenance and Inspections : Warning System
Indication in display
window
149