Table of Contents
Advertisement
Disassembly Procedures
!
Grill Module
1. To remove grill module from range, turn oven controls
off, remove grill grates, grasp grill burners at front
and lift module slightly, then slide module towards
front of the range.
2. To remove grill burner and electrode assembly,
remove screws securing assembly to burner support
and lift assembly out of the pan.
3. To remove burner electrode, remove electrode
mounting screw, bend flashtube shield tab slightly
upward, lift ignitor upward and slide it out through
rear opening.
4. To remove module ground pin, first remove burner
and electrode assembly (step 2) and then remove
ground pin mounting screw and lock-washer.
5. To remove burner support, remove burner and
electrode assembly (step 2) and remove burner
support mounting screws.
Oven Tank
1. Turn off power to the range.
2. Turn off and disconnect gas supply to the range.
3. Disconnect downdraft venting ductwork and remove
range from cabinet.
4. Remove oven door, oven racks and storage drawer.
5. Remove maintop assembly and burner box.
6. Remove upper rear shield mounting screws and
remove shield.
7. Remove rear wire shield mounting screws and
remove shield.
8. Remove rear plenum cover mounting screws and
carefully remove cover.
9. Disconnect bake and broil ignitor wire leads, oven hi-
limit switch wire leads, oven light socket wire leads
and thermostat sensor wire leads at disconnect plug.
10.Remove rear plenum assembly mounting screws.
11. Remove screws securing bake burner orifice support
bracket to rear plenum.
12.Pull rear plenum assembly partially away from range
to allow access to left oven tank hook bolt retaining
nut and flat washer.
13.Remove left and right oven tank hook bolt retaining
nuts and washers and remove hook bolts from oven
tank.
RS2310003 Rev. 0
WARNING
Unplug power source and shut off gas suppl before servicing,
unless testing requires it.
14.Disconnect broil burner supply tubing from broil
burner orifice.
15.Remove broil burner assembly mounting screws and
remove burner and ignitor assembly.
16.Remove broil burner support mounting screws and
remove support.
17.Remove oven tank chip cover mounting screws and
remove cover.
18.Remove oven light lens and bulb.
19.Remove thermostat sensor mounting screws and
remove cover.
20.Remove oven bottom.
21.Remove bake burner ignitor mounting screws and
remove ignitor and mounting bracket assembly.
22.Remove bake burner mounting screw and remove
burner.
23.Remove lower burner box mounting screws and
remove burner box.
24.Remove oven vent mounting screws and remove
vent assembly and vent gasket. Inspect gasket for
damage and replace it if necessary.
25.Disconnect thermal fan switch wire leads and remove
top plenum and switch assembly.
26.Remove screws securing door latch switch mounting
bracket to door latch.
27.Remove latch arm mounting screws and remove arm.
Loosen latch hold-down bracket mounting screw.
28.Remove latch assembly mounting screws and
remove latch assembly.
29.Carefully pull oven tank out of the range.
30.Remove oven light socket, broil burner plate and
gasket, ignitor wire raceway, and broil burner orifice.
Transfer these parts to replacement oven tank.
31.Before inserting replacement oven tank into range,
several pieces of thin gauge sheet metal
(approximately 10" x 28") should be inserted in range
cavity at top, bottom, and sides to help prevent oven
insulation from "bunching up" when replacement tank
is being inserted into range cavity.
32.Carefully push replacement tank into range until the
front lip of tank is approximately inches from the front
frame.
33.Remove pieces of sheet metal and push rest of the
tank into cavity.
34.Reassemble tank using the reverse procedures.
35.After reassembly is completed, check unit for proper
operation.
54
Advertisement
Table of Contents
