Broil Burner Ignitor; Broil Burner/Reflector Assembly; Lower Burner Box; Burner Box - Amana AGDS901 Service Manual

Disassembly Procedures
!
4. Remove oven burner mounting screw located at front
section of lower burner box.
5. Lift the rear of burner off of burner orifice and slide
burner through opening in the rear of the lower

burner box.

6. Reverse procedures to reassemble.
NOTE: When installing burner, verify the open end of
burner slides down over burner orifice. Burner
and orifice can be viewed through storage
drawer opening.

Broil Burner Ignitor

1. Turn off power to the range.
2. Remove oven door and oven racks.
3. Remove screws securing ignitor mounting bracket
and shield to broil burner reflector.
4. Carefully pull ignitor and wire leads into oven cavity.
Remove ceramic wire nuts, disconnect wire leads,
and remove ignitor assembly.
5. Transfer ceramic ignitor wire plug and mounting
bracket and shield to replacement ignitor.
6. Reverse procedures to reassemble.

Broil Burner/Reflector Assembly

1. Turn off power to the range.
2. Remove oven door and oven racks.
3. Remove ignitor shield and bracket mounting screws.
4. Remove burner mounting screws located at front of
the burner and remove burner assembly.
5. Reverse procedures to reassemble.

Lower Burner Box

1. Turn off power to the range.
2. Remove oven door, oven racks, oven bottom and
storage drawer.
3. Remove bake burner ignitor mounting screws and
pull ignitor partially into oven tank.
4. Remove bake burner mounting screw and remove
burner through opening in lower burner box.
5. Remove screws securing lower burner box to bottom
insulation retainer and oven tank and remove lower
burner box.
6. Reverse procedures to reassemble.
NOTE: When reinstalling oven burner, verify open end
of burner slides down over burner orifice. Burner
and orifice can be viewed through storage
drawer opening.
RS2310003 Rev. 0
WARNING
Unplug power source and shut off gas suppl before servicing,
unless testing requires it.
Burner Box
1. Turn off power to the range.
2. Remove maintop assembly (see "Maintop"
procedures).
3. Remove screws securing burner box to left and right
side frames (three screws each side).
4. Remove screws securing left and right plug block and
orifice mounting plates to rear of burner box.
5. Remove fan interlock (bucket) switch mounting
screws and speed nut retainer.
6. Partially remove control panel.
7. Lift burner box to disengage from downdraft top
plenum and remove burner box from range.
8. Remove burner box rear cover plate mounting screws
and transfer plate to replacement burner box.
9. Reverse procedures to reassemble.

Top Burner Valve

1. Turn off power to the range.
2. Turn off gas supply to the range.
3. Partially remove control panel.
4. Remove burner box mounting screws and plug block
orifice mounting plate mounting screws.
5. Disconnect fan interlock (bucket) switch wire leads
and remove burner box.
6. Disconnect spark switch/fan switch wire leads and
remove switch from valve.
7. Disconnect top burner supply tubing from valve.
8. Remove surface valve mounting bolt and remove
valve.
9. Reverse procedures to reassemble.
NOTE: After reassembly verify connections for gas
leaks using a soap solution and check for
proper spark operation.

Surface Burner Supply Tube

1. Turn off power to the range.
2. Turn off gas supply to the range.
3. Remove maintop assembly and burner box.
4. Disconnect burner supply tube fitting from top burner
valve.
5. Remove retaining nut securing orifice and tubing to
plug block and orifice mounting bracket
6. Remove burner supply tube.
7. Reverse procedures to reassemble.
NOTE: After reassembly verify connections for gas
leaks using a soap solution and check for
proper spark operation.
46