Configuring Appletalk Cable Vlans; Configuration Guidelines - HP 9304m Installation And Getting Started Manual

Installation and Getting Started Guide
HP9304-C(config-vlan-ipx-network)# other-proto name block-other-protocols
HP9304-C(config-vlan-other-proto)# exclude e 1/9 to 1/16
HP9304-C(config-vlan-other-proto)# no dynamic
HP9304-C(config-vlan-other-proto)# interface ve 3
HP9304-C(config-vif-3)# ip addr 1.1.10.1/24
HP9304-C(config-vif-3)# ip ospf area 0.0.0.0
HP9304-C(config-vif-3)# int ve4
HP9304-C(config-vif-4)# ipx network 10 ethernet_802.3
HP9304-C(config-vif-4)# vlan 4 name Bridged_ALL_Protocols
HP9304-C(config-vlan-4)# untag ethernet 1/17 to 1/24
HP9304-C(config-vlan-4)# tag ethernet 1/25 to 1/26
HP9304-C(config-vlan-4)# spanning-tree
HP9304-C(config-vlan-4)# vlan 7 name Rtr_BB_to_Bldg.2
HP9304-C(config-vlan-7)# tag e 1/25
HP9304-C(config-vlan-7)# no spanning-tree
HP9304-C(config-vlan-7)# router-interface ve5
HP9304-C(config-vlan-7)# vlan 6 name Rtr_BB_to_Bldg.1
HP9304-C(config-vlan-6)# tag ethernet 1/26
HP9304-C(config-vlan-6)# no spanning-tree
HP9304-C(config-vlan-6)# router-interface ve6
HP9304-C(config-vlan-6)# int ve5
HP9304-C(config-vif-5)# ip addr 1.1.8.2/24
HP9304-C(config-vif-5)# ip ospf area 0.0.0.0
HP9304-C(config-vif-5)# ipx network 8 ethernet_802.3
HP9304-C(config-vif-5)# int ve6
HP9304-C(config-vif-6)# ip addr 1.1.5.2/24
HP9304-C(config-vif-6)# ip ospf area 0.0.0.0
HP9304-C(config-vif-6)# ipx network 5 ethernet_802.3
HP9304-C(config-vif-6)#

Configuring AppleTalk Cable VLANs

You can configure up to eight AppleTalk cable VLANs within a port-based VLAN.
To configure an AppleTalk cable VLAN, you create a port-based VLAN, then create up to eight cable VLANs within
the port-based VLAN. You create the AppleTalk cable VLAN by assigning a number to the VLAN, optionally
naming the cable VLAN, assigning ports from the port-based VLAN, and specifying the router interface (virtual
interface) on which the Routing Switch will send and receive traffic for the cable VLAN.
All the ports in an AppleTalk cable VLAN are within the same AppleTalk cable range. The device switches traffic
within the VLAN and routes traffic between VLANs.

Configuration Guidelines

Use the following guidelines when configuring AppleTalk cable VLANs:
• Up to eight AppleTalk cable VLANs are supported in a protocol-based VLAN. Each VLAN must be numbered
from 1 – 8.
• Each AppleTalk cable VLAN can have only one router interface. The router interface must be a virtual
interface.
• The AppleTalk cable VLANs cannot overlap. Thus, you cannot use the same port in more than one AppleTalk
cable VLAN.
• You must add the ports to the AppleTalk cable VLAN using the static option. You cannot use the dynamic or
exclude options.
• You cannot have an AppleTalk cable VLAN and an AppleTalk protocol VLAN in the same port-based VLAN. If
you already have an AppleTalk protocol VLAN in the port-based VLAN, you must delete the AppleTalk
protocol VLAN first, then configure the AppleTalk cable VLAN.
7 - 28