General Maintenance - Ryobi RBC30SET Operator's Manual

EN
FR DE ES
To start a cold engine:
DO NOT squeeze the throttle trigger until the engine
Q
starts and runs.
Install the battery onto the unit as shown in figure 8.
Q
Lay the trimmer on a flat, level surface.
Q
PRIME - Press the primer bulb at least 7 times, so
Q
fuel is clearly visible.
SET the start lever (item 20) to the START position
Q
on the side of the carburettor.
PRESS the 'safety switch' (item 18) and the 'ignition
Q
switch' to position 3 (item 6) at the same time.
N.B. The safety switch is a rocker type switch and will
Q
automatically reset it's self once released.
N.B. The ignition switch is a 3 position switch.
Q
position 1 is 'off' ("0") position 2 is run, and position
3 ("I") is a rocker type switch which will automatically
reset it's self to position 2 once released.
RELEASE the 2 switches after engine starts - they
Q
will revert back to their resting place.
Wait 6-10 seconds, then squeeze the throttle trigger
Q
to run.
NOTE: Squeezing and releasing the throttle trigger
releases the start lever to the RUN position.
To start a warm engine:
Lay the trimmer on a flat, bare surface.
Q
PRESS the 'safety switch' (item 18) and the 'ignition
Q
switch' (Item 6) at the same time.
RELEASE the 2 switches after engine starts - they
Q
will revert back to their resting place.
MAINTENANCE
WARNING:
When servicing, use only identical replacement
parts. Use of any other parts may create a
hazard or cause product damage.
WARNING:
Always wear safety goggles or safety glasses
with side shields during tool operation. If
operation is dusty, also wear a dust mask.
WARNING:
Before inspecting, cleaning, or servicing the
machine, shut off engine, wait for all moving
parts to stop, and disconnect spark plug lead
and move it away from spark plug. Failure to
follow these instructions can result in serious
personal injury or property damage.
:$51,1*
Neglected or poorly conducted maintenance
may create additional hazards. Do not attempt
to repair or maintain this product if you are not
IT PT NL SV DA
English (original instructions)
NO FI HU CS RU
qualified to do so. If in doubt, return to a Ryobi
service centre for professional assistance.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, lubricant, grease.
WARNING:
Do not at any time let brake fluids, petrol,
p e t r o l e u m - b a s e d p r o d u c t s , p e n e t r a t i n g
lubricants, etc., come in contact with plastic
parts. Chemicals can damage, weaken or
destroy plastic which may result in serious
personal injury.
You can often make adjustments and repairs described
here. For other repairs, have the trimmer serviced by an
authorised service dealer.
INSTALLING REEL EASY LINE TRIMMER HEAD
See Figures 5 .
Stop the engine and disconnect the spark plug wire.
Q
Remove currently installed line trimmer head.
Q
Open the Reel Easy Line Trimmer Head by
Q
depressing the latches on each side. The contents of
the line trimmer head are spring loaded, so keep your
other hand over the line trimmer head cover while
depressing the latches.
Remove the line trimmer head cover, knob, and spool
Q
and set aside.
Place the line trimmer head on the drive shaft. Make
Q
sure the line trimmer head is fully seated.
Install the hex bolt into the opening on the drive shaft
Q
and secure using the hex-shaped opening in the
knob to tighten.
NOTE: Only use the knob to tighten the bolt. The use
of other tools may allow over tightening of the bolt,
which could damage the line trimmer head.
Reinstall the spring into the line trimmer head and
Q
push down to seat.
Reinstall the spool. For the RLT30CET curved line
Q
trimmer attachment, the spool should be placed so
"This side out for curved shaft" is visible. If you are
using a straight shaft attachment with the Reel Easy
cutting head the spool should be placed so "This side
out for straight shaft" is visible.
Replace the knob in the spool.
Q
Replace the line trimmer head cover, aligning latches
Q
with openings in the line trimmer head. Press cover
and line trimmer head together until both latches
snap into openings securely.
Install line as described in the next section of this
Q
manual.
INSTALLING LINE IN REEL EASY LINE TRIMMER
29
RO PL SL HR ET LT LV SK BG