Sharp AR-M450 Service Manual page 72

•The following units are added when the punch unit is installed to the
console finisher:
FPE Punch motor encoder
FPSHPS Punch side register HP
FPUC Punch connection detection
FPDS Punch dust sensor
FPDSS4 Punch side register sensor 4
FPDSS3 Punch side register sensor 3
FPDSS2 Punch side register sensor 2
FPDSS1 Punch side register sensor 1
FPTS Punch timing sensor
3-3
Purpose Operation test, check
Function (Content) Used to check the operation under load in the
finisher and their control circuits.
Section Finisher
Item Operation
Operation/Procedure The display is highlighted when detected.
SIMULATION 3-3
FINISHER LOAD TEST. SELECT 1- , AND PRESS START.
Press [START] key to get started.
SIMULATION 3-3
FINISHER LOAD TEST. EXECUTING...
<List of display values>
Finisher
1 T2S Tray 2 solenoid
2 T2OM Paper exit motor
3 SPS Stopper solenoid
4 SCRS Roller pressure
release solenoid
5 PPS Rear edge h folding
solenoid
6 SCGS Compiler gate
solenoid
7 STTM Staple rotation motor
8 STUM Stapler shift motor
9 MM Main drive motor
10 EVM Elevator motor
11 STM Staple motor
12 JRM Jogger motor rear
13 JFM Jogger motor front
14 PSM Pusher motor
2
Press [CUSTOM SETTING] key to stop.
2
Console finisher
1 FFC Folding clutch
2 FPSM Puncher side register
motor
3 FPNM Punch motor
4 FLM Shift motor
5 FFSM Stapler motor
6 FSM Slide motor
7 FRJM Alignment motor R
8 FFJM Alignment motor F
9 FAM Bundle exit motor
10 FPM Paddle motor
11 FFM Transport motor
AR-M350 SIMULATIONS 10-11
3-6
Purpose Adjustment
Function (Content) Used to adjust the stacking capacity of the
finisher (AR-FN6). (Used to adjust the alignment
plate (jogger) stop position in the finisher paper
width direction. The adjustment is made by
changing the alignment plate home position in
the paper width direction by software. )
Section Finisher
Item Operation
Operation/Procedure Enter the adjustment value with 10 digit key pad
and press START key. The jogger moves to LT
position (Inch series) or A4 position (AB series)
according to the entered value, and stops there.
SIMULATION 3-6
FINISHER JOGGER ADJUSTMENT. INPUT VALUE 40-60, AND PRESS START.
Press [START] key to get started.
SIMULATION 3-6
FINISHER JOGGER ADJUSTMENT. MOVING...
(Stored on PCU PWB)
3-10
Purpose Adjustment
Function (Content) Used to adjust the console finisher (AR-FN7).
Section Finisher
Item Operation
Operation/Procedure Setting of the console finisher is performed.
SIMULATION 3-10
CONSOLE FINISHER SETTING. SELECT 1-10, AND PRESS START.
1. SADDLE POSITION 2. FOLDING POSITION
3. FRONT ADJUST
4. REAR ADJUST 5. STAPLE REAR
6. STAPLE FRONT 7. STAPLE BOTH
8. STAPLE PITCH 9. PUNCH CENTER
10. PUNCH HOLE
Press [START] key to get started.
SIMULATION 3-10
CONSOLE FINISHER SETTING. INPUT VALUE, AND PRESS START.
1. FOLDING POSITION
<List of set values>
Adjustment content
1 Saddle binding position adjustment
2 Saddle folding position adjustment
3 Front alignment position adjustment
4 Rear alignment position adjustment
5 Staple rear one-position binding position adjustment 0~200
6 Staple front one-position binding position adjustment 0~200
7 Staple 2-position binding center adjustment
8 Staple 2-position binding pitch adjustment
9 Punch center adjustment (Slide direction)
10 Punch hole position adjustment (Paper feed direction) 0~99
(Values stored in EEPROM)
50
Press [CUSTOM SETTING] key to stop.
Stops when the operation is terminated.
50
1
Press [CUSTOM SETTING] key to stop.
200
Initial
Range 1STEP
value
0~400 200 0.0707mm
0~400 200 0.0525mm
0~20 10 0.367mm
0~20 10 0.367mm
100 0.04374mm
100 0.04374mm
0~200 100 0.04374mm
0~99 50 0.04374mm
47~53 50 1mm
50 0.105mm