Sharp AR-M450 Service Manual page 104

46-16
Purpose Adjustment
Function (Content) Used to adjust the reading density in the FAX
mode (super fine mode). (Only when FAX is
installed.)
Section
Item Picture quality
Operation/Procedure The exposure mode to be set is selected.
(FAX super fine mode individual adjustment)
1) The current set value is highlighted on the
right side of each item. In this screen, be sure
to select "1: COPY START." (Set value: 1)
2) Set the exposure level with 10 digit key pad.
Press P to store the set value.
(Default: 50, set range: 0 - 99)
3) Press START, and copying is started and the
set value is stored. (Display value 1)
4) Select a paper feed tray. (Set value 2)
5) Select an exposure level. (Set value 3)
SIMULATION 46-16
EXP. LEVEL SETUP FAX(ULTRA FINE). SELECT 0-8, AND PRESS START.
0. TRAY SELECT 1 1. PRINT START
2. EXP LEVEL 1
3. AUTO 4. LIGHT
6. AUTO(H) 50 7. LIGHT(H)
Select other than 0 - 2,
and press [START] key.
SIMULATION 46-16
EXP. LEVEL SETUP FAX(ULTRA FINE),INPUT VALUE 0-99, AND PRESS
START.
2. AUTO
Select 1, and
Press [START] key.
press [START] key.
SIMULATION 46-16
EXP. LEVEL SETUP FAX(ULTRA FINE). NOW COPYING.
Select 0, and
press [START] key.
SIMULATION 46-16
EXP. LEVEL SETUP FAX(ULTRA FINE). SELECT 1-5, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4 5. BPT
Select 2, and
press [START] key.
SIMULATION 46-16
EXP. LEVEL SETUP FAX(ULTRA FINE). SELECT 3-8, AND PRESS START.
(EXP. LEVEL SELECT)
3. AUTO 4. LIGHT
6. AUTO(H) 7. LIGHT(H)
1
5. DARK
50
50 8. DARK(H)
Press [CUSTOM SETTING] key.
50
Press [CUSTOM SETTING] key.
Or copying is terminated.
Press [START] key or
press [CUSTOME SETTING] key.
1
Press [START] key or
press [CUSTOME SETTING] key.
1
5. DARK
8. DARK(H)
AR-M350 SIMULATIONS 10-43
<List of set values 1>
0 Paper feed tray selection
1 Print start (Default)
2 Exposure level selection
3 Auto
4 Bright
5 Dark
6 Auto (Half tone)
7 Bright (half tone)
8 Dark (Half tone)
<List of display values 1>
Normal display
ERROR display Door open
Jam
Paper empty
<List of set values 2>
1 TRAY1
2 TRAY2
3 TRAY3
4 TRAY4
5 Manual feed
<List of set values 3>
3 Auto
4 Bright
5 Dark
6 Auto (Half tone)
7 Bright (half tone)
8 Dark (Half tone)
46-17
Purpose Adjustment, setup, operation data output, check
(display)
Function (Content) Used to adjust the CCD/CIS shading reference
value.
Section Scanner (reading) / DSPF (reading)
Item Operation
Operation/Procedure 1) Change the shading reference value of
CCD/CIS. The current set value is displayed
don the right of each item. (Set value)
2) Set the exposure level with 10 digit key pad.
Press START to store the set value.
(Default: 128, set range: 0 - 255)
SIMULATION 46-17
CCD/CIS SHADING GAIN DATA SETUP. SELECT 1-3, AND PRESS START.
1. CCD ODD 128 2. CCD EVEN
3. CIS
128
Press [START] key.
SIMULATION 46-17
CCD SHADING GAIN DATA SETUP.INPUT VALUE 0-255, AND PRESS
START.
1. CCD ODD
<Set values>
1 CCD CDD
2 CCD EVEN
3 CS
NOW COPYING
DOOR OPEN.
JAM
PAPER EMPTY.
128
1
Press [CUSTOM SETTING] key.
128