Warning System; Cases Indicated By Error Codes; Cases Indicated By Error Messages - Panasonic AJ-PX270 Operating Instructions Manual

Warning system

If an error is detected immediately after the camera is turned on or during operation, the viewfinder, LCD monitor, and tally lamp indicate the error. Deal
with the error by following the indications.

Cases indicated by error codes

Error code Display
[TURN POWER OFF]
[E-30]
[P2 CARD]
[TURN POWER OFF]
[E-31]
[SYSTEM MODE]
[SYSTEM ERROR]
[E-33]
[CAMERA]
[SYSTEM ERROR]
[E-35]
[CODEC]
[SYSTEM ERROR]
[E-36]
[P2 SYSTEM]
[SYSTEM ERROR]
[E-37]
[P2CS]
[SYSTEM ERROR]
[E-39]
[INITIALIZE]
[SYSTEM ERROR]
[E-64] [FRAME SIGNAL]
(or no display)

Cases indicated by error messages

During recording/playback
Display
[AUTH NG CARD] (slot number)
[BACKUP BATT EMPTY]
[SET DATE AND TIME]
[CARD ERROR] (slot number)
[DIR NG CARD] (slot number)
[FAN STOPPED]
[HIGH TEMPERATURE]
[PB INTERMITTENT] (slot number)
Chapter 10 Maintenance and Inspection — Warning system
Description
An error occurred in the camera built-in memory
because the P2 card being accessed was ejected.
f Tally lamp flashes four times per second.
System mode error occurred.
f Tally lamp flashes four times per second.
Camera unit error occurred.
f Tally lamp flashes four times per second.
Codec control error occurred.
f Tally lamp flashes four times per second.
P2 system error occurred.
f Tally lamp flashes four times per second.
P2CS microcomputer error occurred.
f Tally lamp flashes four times per second.
Video initialization error occurred.
f Tally lamp flashes four times per second.
Reference signal error occurred.
f Tally lamp flashes four times per second.
Description
CPS authentication of microP2 memory card has failed.
The microP2 memory card whose CPS authentication
failed cannot be recorded or played back.
Displays any reduced voltage detected on the backup
battery in the internal clock when the power is turned
on.
Displayed when the internal clock setting is reset.
Displayed when an data error caused by the P2 card
occurs during recording.
Displayed after recording stops until the next operation.
Also displayed for three seconds during playback when
a P2 card error causes playback to stop.
f If the error occurs during recording, the tally lamp
flashes four times per second for approx. three
seconds after recording stops.
f The tally lamp does not flash when an error occurs
during playback.
The directory position is not correct.
Displayed when the fan motor stops.
The temperature inside the camera is higher than that of
the normal conditions.
Playback is interrupted on the SDHC/SDXC memory
card. A card whose playback performance cannot be
assured is inserted.
– 203 –
Behavior and cause
f Cannot operate.
f Follow the message to turn off the power once and
turn on the power again.
f Ensure that there is no error in the clips on the ejected
card, and restore the clips as necessary.
f Cannot operate.
f Follow the message to turn off the power once, turn
on the power again, and check that there is no error
display.
f The operation stops.
f Contact your dealer.
f The operation stops.
f Contact your dealer.
f The operation stops.
f Contact your dealer.
f The operation stops.
f Contact your dealer.
f The operation stops.
f Contact your dealer.
f The operation stops.
f Contact your dealer.
Behavior and cause
f The current operation will continue.
f Select [AUTHENTICATE] in the main menu → [CLIP],
and enter the password.
f The current operation will continue.
f Charge the built-in battery.
f The current operation will continue.
f Set the date/time of the internal clock. (page 33)
f The operation will stop.
f After it stops, the P2 card on which the error occurred
is write-protected. Replace the P2 card of the slot
where the error occurred.
f The current operation will continue.
f Make a card backup immediately and format the card
to use it again.
f The current operation will continue.
f If the fan has stopped with error, stop using the
camera immediately and consult your dealer.
f If the fan has stopped, temperature of the camera
will rise. Therefore, do not use the camera for a long
period of time.
f The current operation will continue.
f Turn off the power of the camera, turn it on again,
and check recording and playback operations. If the
problem persists, consult your dealer.
f The current operation will continue.
f Use of microP2 or P2 memory card is recommended.