Camera Status Display - Panasonic AJ-PX270 Operating Instructions Manual

f [CLIP&T&=] ([CLIP&T~&]): Cueing up (rewinding) by clip and text memo (when [CLIP&TEXT MEMO] is set in the main menu → [OTHER
FUNCTIONS] → [SEEK POS SEL])
f [START]* : Displayed when recording of a new clip is started in one-clip recording.
1
f [END]* : Displayed when combining of clips is ended in one-clip recording.
1
f [L-]* : Loop recording
2
f [I-]* : Interval recording, one-shot recording
2
f [P-]* : Pre-recording
2
*1 If the display is set to [OFF], only [REC], [START], and [END] are displayed. Also, when pre-recording, loop recording, interval recording, or one-shot
recording is set, it is displayed.
*2 Displayed when [INTERVAL], [ONE SHOT], or [LOOP] is set in the main menu → [RECORDING SETUP] → [RECORDING], or when [ON] is set in the
main menu → [RECORDING SETUP] → [PRE REC].
43 <AUTO/MANUAL> switch operation display
Displayed when the <AUTO/MANUAL> switch is set to <AUTO>.
44 Rec during upload function status display
Displays the status of rec during upload.
f [ ]: Displayed when the rec during upload function is enabled.
The display will blink when recording is started immediately after the power is turned on or the P2 card is inserted, and the upload will not be
executed until the recording is stopped.
f [ ]: Displayed during upload.
f [ ]: Displayed from when transfer error occurred during upload until when the next upload starts.
45 GPS display
Displays the strength of the GPS signal reception in four levels. The GPS signal strength is indicated by the number of vertical bars. It is not
displayed when GPS is disabled.
46 Streaming distribution status display
Displays the streaming status.
f [ ] (flashing): Flashes while the camera is being connected to a device which will receive the streaming video.
f [ ] (illuminated): Displayed when the camera is connected to a device receiving the streaming video and the camera is transmitting streaming
video.
The display turns off when a connection could not be established properly.
@ NOTE
t Depending on the network status, the [
47 HD SDI REMOTE recording status and 4G/LTE connection status
Displays the control status of whether recording has started or stopped for an external device which is connected to the <SDI OUT> terminal.
When the main menu → [OUTPUT SEL] → [HD SDI REMOTE] is set to [ON], it will always be displayed regardless of the settings in the main menu
→ [DISPLAY SETUP]. It is not displayed when [HDSDI REMOTE] is set to [OFF].
f [SDIn]: Status where the recording is being instructed for an external device
f [SDI&]: Status where recording stop is being instructed for an external device
Displays the 4G/LTE connection status. Displays at the 4G/LTE connection. Displays the strength of the signal reception in six levels. Displays the
radio wave strength with the number of vertical bars. It is not displayed when the setting of 4G/LTE is disabled.
f [4G/LTE ]: During 4G/LTE connection
f [4G/LTE ]: When not connected with 4G/LTE
f [4G/LTE ]: When there is a problem with the 4G/LTE connection
@ NOTE
t Depending on the USB modem that is supported, vertical bars that indicate the signal strength may not be displayed.
48 Audio monitor volume adjustment display
Displayed when the <AUDIO MON/ADV> button is pressed for volume adjustment of speaker or headphones. The display disappears three seconds
after the operation.
49 Front audio level volume display
The volume is displayed for three seconds when it is adjusted with the <F.AUDIO LEVEL> dial.

Camera status display

These are indicated in the information display area in the center.
[ABB]: Displayed while automatic black balance operation is active.
[ATW ACTIVE]: Displayed when the <AWB> button is pressed while auto tracking white balance is active.
[ATW]/[ATW LOCK]: Displayed when the <WHITE BAL> switch is turned to <B> if [ATW] is allocated.
[AWB]: Displayed while automatic white balance operation is active.
[AWB P3200K]/[AWB P5600K]: When the <WHITE BAL> switch is at <PRST> position, displays the color temperature assigned to <PRST>. It is also
displayed when you attempt to perform automatic white balance with the switch at <PRST> position.
[BACK LIGHT]: Displayed when pressing the USER button to which [BACK LIGHT] is allocated for iris control and switching the status.
[GAIN**dB]: Displayed when gain is switched.
[IRIS:MANUAL]/[IRIS:AUTO]: Displayed when you switch the iris operation.
[SHUTTER 1/****]/[SHUTTER OFF]: Displayed when you switch the shutter speed.
[SPOT LIGHT]: Displayed when pressing the USER button to which [SPOT LIGHT] is allocated for iris control, and switching the status.
Chapter 7 Display — Screen status display
] display may not be able to follow during actual operation.
– 158 –