Panasonic AJ-PX270 Operating Instructions Manual page 139

Item
[START DELAY]
[PRE REC]
[ONE CLIP REC]
[SIMUL REC]
[BACKGROUND REC]
[DUAL CODEC [CODEC USAGE]
SETTING]
[STREAMING MODE]
[PROXY REC MODE]
[PROXY DISP]
[QoS MAX RATE]
[QoS MIN RATE]
[STREAMING
LATENCY]
[START TEXT MEMO]
[TIME STAMP]
[DF MODE]
[TCG]
[TC PRESET]
Chapter 6 Menu Operations — Menu list
Selects whether to delay the recording start time by approximately one second when performing interval
recording or one-short recording.
[ON], [OFF]
f Factory setting: [OFF]
Selects whether to perform pre-recording. If [ON] is selected, pre-recording is performed for approximately
three seconds in HD, and for approximately seven seconds in SD.
[ON], [OFF]
f Factory setting: [OFF]
Selects whether to perform one-clip recording.
[ON], [OFF]
f Factory setting: [OFF]
Selects whether to perform simultaneous recording.
[ON], [OFF]
f Factory setting: [OFF]
Selects whether to perform background recording.
[ON], [OFF]
f Factory setting: [OFF]
Selects media for recording proxy data.
[PROXY REC(P2)]: Records proxy data to a P2 card.
[PROXY REC(P2&SD)]: Records proxy data to both of a P2 card and SD memory card.
[STREAMING]: Outputs streaming.
[OFF]: Does not record proxy data.
f Factory setting: [OFF]
If the [CODEC USAGE] setting cannot be changed, change the [PROXY REC MODE] or [STREAMING
MODE] setting.
Sets the transfer mode for streaming.
[LOW], [HQ], [AVC-G6], [SHQ (QoS)], [AVC-G (QoS)]
f Factory setting: [HQ]
Sets the recording mode of proxy data.
[LOW 2CH MOV], [HQ 2CH MOV], [SHQ 2CH MOV], [AVC-G6 2CH MOV]
f Factory setting: [HQ 2CH MOV]
Selects whether to display proxy data recorded information or messages in the viewfinder and LCD
monitor.
[ON]: Displays proxy recording information and SD memory card remaining capacity at the start of
recording. Warning information is displayed at all times.
[OFF]: Displays proxy and SD memory card warning information for only three seconds when warning
occurs.
f Factory setting: [OFF]
Sets the maximum bitrate for video data when the QoS is operating. This setting is used when the
streaming distribution is started from the operation of the camera.
This can be set when [CAMERA] is selected in the main menu → [NETWORK SETUP] → [STREAMING
SETTING] → [START TRIGGER].
[256Kbps], [512Kbps], [1Mbps], [1.5Mbps], [2.5Mbps], [3.5Mbps], [6Mbps], [9Mbps]
f Factory setting: [9Mbps]
[9Mbps] cannot be selected when [STREAMING MODE] is set to [SHQ (QoS)].
Sets the minimum bitrate for video data when the QoS is operating. This setting is used when the
streaming distribution is started from the operation of the camera.
This can be set when [CAMERA] is selected in the main menu → [NETWORK SETUP] → [STREAMING
SETTING] → [START TRIGGER].
[256Kbps], [512Kbps], [1Mbps], [1.5Mbps], [2.5Mbps], [3.5Mbps], [6Mbps], [9Mbps]
f Factory setting: [256Kbps]
Sets the delay mode during the streaming distribution. This setting is used when the streaming distribution
is started from the operation of the camera.
This can be set when [CAMERA] is selected in the main menu → [NETWORK SETUP] → [STREAMING
SETTING] → [START TRIGGER].
[NORMAL]: Sets if you want to emphasize the stability of streaming.
[SHORT]: Sets if you want to emphasize the reduction of streaming delay.
f Factory setting: [NORMAL]
Selects whether to automatically add a text memo at recording start position each time recording is started.
[ON], [OFF]
f Factory setting: [OFF]
Selects whether to superimpose [DATE]/[TIME] information on shot videos.
[ON]: Superimposes information set in the [DATE]/[TIME] item on video.
[OFF]: Does not superimpose information set in the [DATE]/[TIME] item on video.
f Factory setting: [OFF]
Sets the counting method of the built-in time code generator.
[DF]: Uses the drop frame mode.
[NDF]: Uses the non-drop frame mode.
f Factory setting: [DF]
Sets the operation mode to advance the built-in time code generator.
[FREE RUN]: Advances regardless of the operation mode.
[REC RUN]: Advances when recording is in process.
f Factory setting: [REC RUN]
In native recording in variable frame rate mode, if the number of frames differs for shooting and recording,
the time code operation will be [REC RUN].
Sets the default value of the time code to record.
– 139 –
Description of settings