Table of Contents
Advertisement
Warning system
If an error is detected immediately after the camera is turned on or during operation, the viewfinder, LCD monitor, and tally lamp indicate the error. Deal
with the error by following the indications.
Cases indicated by error codes
Error code
Display
[TURN POWER OFF]
[E-30]
[P2 CARD]
[TURN POWER OFF]
[E-31]
[SYSTEM MODE]
[SYSTEM ERROR]
[E-33]
[CAMERA]
[SYSTEM ERROR]
[E-35]
[CODEC]
[SYSTEM ERROR]
[E-36]
[P2 SYSTEM]
[SYSTEM ERROR]
[E-37]
[P2CS]
[SYSTEM ERROR]
[E-39]
[INITIALIZE]
[SYSTEM ERROR]
[E-64]
[FRAME SIGNAL]
(or no display)
Cases indicated by error messages
During recording/playback
Display
[AUTH NG CARD] (slot number)
[BACKUP BATT EMPTY]
[SET DATE AND TIME]
[CARD ERROR] (slot number)
[DIR NG CARD] (slot number)
[FAN STOPPED]
[HIGH TEMPERATURE]
[PB INTERMITTENT] (slot number)
Chapter 9 Maintenance — Warning system
Description
An error occurred in the camera built-in memory
because the microP2 memory card being accessed
was ejected.
f Tally lamp flashes four times per second.
System mode error occurred.
f Tally lamp flashes four times per second.
Camera unit error occurred.
f Tally lamp flashes four times per second.
Codec control error occurred.
f Tally lamp flashes four times per second.
P2 system error occurred.
f Tally lamp flashes four times per second.
P2CS microcomputer error occurred.
f Tally lamp flashes four times per second.
Video initialization error occurred.
f Tally lamp flashes four times per second.
Reference signal error occurred.
f Tally lamp flashes four times per second.
Description
CPS authentication of microP2 memory card has failed.
The microP2 memory card whose CPS authentication
failed cannot be recorded or played back.
Displays any reduced voltage detected on the backup
battery in the internal clock when the power is turned
on.
Displayed when the internal clock setting is reset.
Displayed when a data error caused by the microP2
memory card has occurred during the recording.
Displayed after recording stops until the next operation.
Displayed for three seconds when the playback has
stopped due to error of the microP2 memory card
during the playback.
f If the error occurs during recording, the tally lamp
flashes four times per second for approx. three
seconds after recording stops.
f The tally lamp does not flash when an error occurs
during playback.
The directory position is not correct.
Displayed when the fan motor stops.
The temperature inside the camera is higher than that
of the normal conditions.
Playback is interrupted on the SDHC/SDXC memory
card. A card whose playback performance cannot be
assured is inserted.
– 156 –
Behavior and cause
f Cannot operate.
f Follow the message to turn off the power once and
turn on the power again.
f Ensure that there is no error in the clips on the
ejected card, and restore the clips as necessary.
f Cannot operate.
f Follow the message to turn off the power once, turn
on the power again, and check that there is no error
display.
f The operation stops.
f Contact your dealer.
f The operation stops.
f Contact your dealer.
f The operation stops.
f Contact your dealer.
f The operation stops.
f Contact your dealer.
f The operation stops.
f Contact your dealer.
f The operation stops.
f Contact your dealer.
Behavior and cause
f The current operation will continue.
f Select [AUTHENTICATE] in the main menu → [CLIP],
and enter the password.
f The current operation will continue.
f Charge the built-in battery.
f The current operation will continue.
f Set the date/time of the internal clock. (page 36)
f The operation will stop.
f Once it has stopped, the microP2 memory card
where the error has occurred is write-protected.
Replace the microP2 memory card in the slot where
the error has occurred.
f The current operation will continue.
f Make a card backup immediately and format the card
to use it again.
f The current operation will continue.
f If the fan has stopped with error, stop using the
camera immediately and consult your dealer.
f If the fan has stopped, temperature of the camera
will rise. Therefore, do not use the camera for a long
period of time.
f The current operation will continue.
f Turn off the power of the camera, turn it on again,
and check recording and playback operations. If the
problem persists, consult your dealer.
f The current operation will continue.
f It is recommended to use the microP2 memory card.
Advertisement
Table of Contents
