Denon AVR-2313CI Owner's Manual page 156

GAudioH
Symptom
Audio is not output. • Check the connections for all devices.
• Check the speaker connections and configurations.
• Check whether the audio device power is turned on.
• Adjust the master volume.
• Cancel the mute mode.
• Check the connection with the playback device and select the
proper input source.
• Match the input mode and the terminal assigned to be the digital
input terminal.
• Disconnect the headphones. No sound is output from the
speakers when headphones are connected.
The volume does not • The maximum volume is set too low. Set the maximum volume
increase. using "Limit"on the menu.
• Power for external devices connected to the output connectors
of the unit may not be turned on. Check the power of connected
external devices.
No sound is • Check if the surround speakers are connected to the SURROUND
produced from terminals.
surround speaker.
No sound is • Check if "Assign Mode" is set appropriately in order to output
produced from audio from the surround back speakers.
surround back • Set "Speaker Config." – "Surr. Back" on the menu to something
speaker. other than "None".
• Set the sound mode to something other than "STEREO" and
"VIRTUAL".
No sound is • Check if "Assign Mode" is set appropriately in order to output
produced from front audio from the front height speakers.
height speaker. • Set "Speaker Config." – "Front Height" on the menu to something
other than "None".
No sound is • Check if "Assign Mode" is set appropriately in order to output
produced from front audio from the front wide speakers.
wide speaker. • Set "Speaker Config." – "Front Wide" on the menu to something
other than "None".
DVD
Cause/Solution
9,
15,
19,20,
79,
83,84,
Symptom
Page
No sound is • Check the subwoofer connections.
1 0, 1 3, 1 4, produced from
subwoofer. • Turn on the subwoofer's power.
1 6, 1 7, 1 8,
2 1, 2 3 • Set "Speaker Config." – "Subwoofer" on the menu to "Yes".
• If "Front" and "Center" for "Speaker Config." are set to "Large",
and "Subwoofer Mode" is set to "LFE", no sound may be output
8 0, 8 1, 8 2,
from the subwoofers, depending on the input signal or selected
8 5, 8 6
sound mode.
–
DTS sound is not • Set "Decode Mode" on the menu to "Auto" or "DTS".
33, 96
output.
33, 96
Dolby TrueHD, DTS- • Make HDMI connections.
32, 96
HD, Dolby Digital
Plus audio is not
117
output.
• Check that "Speaker Config." – "Center" or "Surround" is set to
Dolby PLg mode or
135
other than "None". If the speaker system is 2.0/2.1ch, this sound
DTS NEO:6 mode
mode cannot be selected.
cannot be selected.
106
• When headphones are used, Dolby PLg or DTS NEO:6 cannot be
selected.
–
Audyssey MultEQ ®
• Switch the sound mode to other than "DIRECT" or "PURE
XT, Audyssey DIRECT".
Dynamic EQ ® and • When headphones are used, Audyssey MultEQ ® XT, Audyssey
–
Dynamic EQ ® and Audyssey Dynamic Volume ® cannot be
Audyssey Dynamic
Volume ® cannot be
selected.
selected.
120
Audyssey DSX ®
• Check that "Speaker Config." – "Front Height" or "Front Wide" is
cannot be selected. set to other than "None".
121
• Check that "Speaker Config." – "Center" is set to other than
"None".
69
• Switch the sound mode to DOLBY listening mode or DTS listening
mode.
120 • When headphones are used, Audyssey DSX ® cannot be selected.
• Run Audyssey ® Setup.
Audyssey Dynamic
121
EQ ® and Audyssey
Dynamic Volume ®
120
cannot be selected.
"Restorer" cannot • Check that an analog signal or PCM signal (Sample Rate=44.1/48
121
be selected. kHz) is input. For playback of multichannel signals such as Dolby
Digital or DTS surround, "Restorer" cannot be used.
• Switch the sound mode to other than "DIRECT" or "PURE
DIRECT".
153
Cause/Solution
79,
83,84,
Page
8 0, 8 1, 8 2,
8 5, 8 6
–
120
120, 121
117
10
120
–
69
–
121
120
69
–
25, 87
105
69