Ver. 6 Please refer to the MODIFICATION NOTICE. SERVICE MANUAL MODEL E1K E1C AVR-1912 AVR-2112CI INTEGRATED NETWORK AV RECEIVER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. •...
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. LEAKAGE CURRENT CHECK Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
[AM]18 μV n Remote Control Unit (RC-1156) Batteries : R6/AA Type (two batteries) Maximum external dimensions : 53 (W) x 224 (H) x 28 (D) mm DIMENSION Weight : 160 g (including batteries) [AVR-1912E3 model] 30.5 30.5 86.0 344.0 435.0...
Page 6
[AVR-1912E2/EA/E1C,2112CIE3 model] s 35.5 30.5 86.0 344.0 435.0...
PRESET CHANNEL 3 PRESET CHANNEL 2 Service Jig When you repair the printing board, you can use the following JIG (Extension cable kit). Please order it from Denon Official Service Distributor in your region if necessary. 8U-110084S EXTENSION UNIT KIT 1 Set (Refer to 43 page.)
DISASSEMBLY • Disassemble in order of the arrow in the following figure. • In the case of the re-assembling, assemble it in order of the reverse of the following flow. • In the case of the re-assembling, observe "attention of assembling". •...
Page 9
About the photos used for "descriptions of the DISASSEMBLY" section • The shooting direction of each photograph used herein is indicated on the left side of the respective photograph as "Shooting direction: ***". • Refer to the diagram below about the shooting direction of each photograph. •...
(2) Cut the wire clamp band, then disconnect the connector wires and FFC cable. Remove the screws. STYLE PIN : Loosen CP101 Except the AVR-1912E3 model. STYLE PIN : Loosen FFC cable Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in FRONT PANEL ASSY.
2. PCB RS232C (AVR-2112CI only) Proceeding : TOP COVER PCB RS232C (AVR-2112CI only) → (1) Remove the screws. Shooting of photograph: A Please refer to "EXPLODED VIEW" for the disassembly method of PCB RS232C.
3. PCB HDMI Proceeding : TOP COVER PCB RS232C (AVR-2112CI only) PCB HDMI → → (1) Remove the screws. Shooting of photograph: A (2) Cut the wire clamp band, then disconnect the connector wires and FFC cable. Disconnect the connector board. FFC cable Board to board Board to board...
4. POWER TRANS MAIN Proceeding : TOP COVER PCB RS232C (AVR-2112CI only) PCB HDMI → → POWER TRANS MAIN → (1) Disconnect the connector wires, then remove the screws. CP101 STYLE PIN : Loosen CX102 CP102,104 5. PCB AUDIO_VIDEO ASSY Proceeding : TOP COVER PCB RS232C (AVR-2112CI only)
(3) Remove the PCB SMPS/PCB SPK from the CHASSIS, then cut the wire clamp band. PCB SMPS PCB SPK Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B. 7. PCB REG/PCB REG_CNT Proceeding : TOP COVER PCB RS232C (AVR-2112CI only) PCB HDMI →...
8. RADIATOR ASSY Proceeding : TOP COVER RADIATOR ASSY → (1) Remove the screws. View from the bottom (2) Disconnect the connector wires and FFC cable. STYLE PIN : Loosen CP401 CP402 CP403 CP405 FFC cable...
Page 17
(3) Remove the screws. Shooting direction: C Shooting direction: D CP101 STYLE PIN : Loosen Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in RADIATOR ASSY.
STATUS paths. (Troubleshooting) CHANNEL 1 The signal paths of the set can be easily confirmed after repair. When using multiple DENON AV receivers in the same room, make PRESET Remote ID Setup mode STATUS this setting so that only the desired AV receiver operates.(Refer to 25...
STATUS paths. (Troubleshooting) CHANNEL 1 The signal paths of the set can be easily confirmed after repair. When using multiple DENON AV receivers in the same room, make PRESET Remote ID Setup mode STATUS this setting so that only the desired AV receiver operates.(Refer to 25...
1. µcom/DSP Version display mode 1.1. Operation specifications µcom/DSP version display mode: When the set is started up in this mode, the version information is displayed. Starting up: Press the "ON/STANDBY" button to turn on the power while pressing the "STATUS" and "iPod 1 " buttons. Now, press the "STATUS"...
Page 21
i Ethernet(DM860) 1st Boot Loader, Hardware ID : E t h e r n e t F B L Press the "STATUS" button. * * * * * * * * - b d o Ethernet(DM860) 2nd Boot Loader, Rhapsody Flag : E t h e r n e t S B L Press the "STATUS"...
1.3. Error display See the following table for each "Error information" display and its explanation (status). Display order is q , w , e , r , t . Condition Status FL Display Trouble shooting • Please check the Compared with the destination setting destination-resistors (R773/R776, HDMI on the board.
When the set is started up in this mode, the error information is displayed. Starting up: [AVR-1912E3 model] Press the "ON/STANDBY" button to turn on the power while pressing the "STATUS" and "NET/USB" buttons. The error (protection history display) mode is set.
Page 24
2.3. Clearing the protection history There are two ways to clear the protection history, as described below. (1) Start up the set in error (protection display) mode and display the error, then press and hold down the "INTERNET RADIO" button for 3 seconds. P R T : D C Press and hold down "INTERNET RADIO"...
3. Remote ID Setup mode 3.1. Specifications When using multiple DENON AV receivers in the same room, make this setting so that only the desired AV receiver operates. When you change the remote ID, make sure that the remote control unit and the remote ID of the main unit are exactly the same.
4. DIAGNOSTIC MODE (Video/Audio (signal) path confirmation mode) This mode is used for confirming the Video and Audio (signal) paths. (Troubleshooting) Confirming the operation of unit can be easily done after repair. Backup data will not be lost. 4.1. Starting diagnostic mode Press the ON/STANDBY button to turn on the power while pressing both the "PRESET CHANNEL1" button and the "STATUS" button at the same time. d Q1, Q2 and Q3 are lit in FL display.
Page 28
4.5. Audio system confirmation items fig.XX : Refer to the block diagram of the fig.XXth. Output sequence of remote control codes Confirmation item Setting and display Details of how to operate remote controller Contents of confirmation Remarks b It is useful to form a macro program. Analog (signal) Path Input Mode : Fixed ANALOG 1.Press [AMP]...
When you repair the printing board, you can use the following JIG (Extension cable kit). Please order it from DENON Official Service. Distributor in your region if necessary. NOTE: The incorrect connection with in the JIG (EXTENSION UNIT KIT) may cause damage.
Page 44
(4) Connect the six extension jig cables. PCB HDMI Connection table of Board to Board Ref. No. Ref. No. 13 pin SIDE CNT HDMI 19 pin SIDE CNT HDMI 33 pin CP11 FRONT CNT HDMI 13 pin CP10 FRONT CNT HDMI 13 pin FRONT CNT...
WHEN THE MICROPROCESSOR IS REPLACED WITH A NEW ONE When the U-PRO (Microprocessor) or the Flash ROM is replaced, confirm the following. After PWB Name Ref. No. Description Remark replaced HDMI IC41 R5F56108VNFP SOFTWARE: Main HDMI EN29LV160BB-70TIP SOFTWARE: DSP ROM HDMI IC22 EPM3032A-TC44...
Page 46
[AVR-2112CI model] s 1.1. Preparations before starting the operation (1) Personal Computer (Installed "DFW_0049_AVR1912_2112_(Rev.X.X.X).exe". (2) RS-232 cable (9P (Male ), Straight). 1.2. Connection of AV receiver (1) Confirm the power on/off switch of the AV receiver is turning off. (2) Connect the RS-232C cable from PC with the "RS232C Terminal of AV receiver". RS-232C Cable [All model commonness] 1.3.
Page 47
(3) When connection is good, then you can see the "Communication check OK." message. (4) If connection is not good, then you can see the "Communication check NG" message. Please confirm the following (a) Check the connection of the AV receiver and PC. (refer to "1.2. Connection of the AV receiver" ) (b) Check the operation mode of the AV receiver.
Page 48
1.7. Complete the firmware updating (1) Click the "Update" button. XXXXXXXX XXXXXXX (2) When writing of the firmware is completed, the power of AV receiver turns on automatically and you can see the "Update completed" message. (3) If you can’t complete the firmware update, please retry the firmware update from "1.3. Turn on the AV receiver". 1.8.
2. How to update by DPMS You can update the firmware by downloading the latest version from the Internet. 2.1. Connecting to the Network (1) System requirements • Internet Connection by Broadband Circuit • Modem • Router • Ethernet cable (CAT-5 or greater recommended) (2) Setting Internet Computer...
Page 50
2.3. About the error code d See the table below for error codes, details of faults, and coping strategies when the firmware is updated through DPMS (Denon Product Management Server). Error Details of Error code Display Coping strategies Code Reset and update again.
Page 51
Error Details of Error code Display Coping strategies Code Main CPU failed to receive firmware Turn off and on the power. for rewriting sent from DM860 (when U p d a t i n g f a i l Updating starts automatically. an error occurred).
Page 52
Error Details of Error code Display Coping strategies Code Check the network connection. Connection to DPMS timed out Carry out the update in an environment C o n n e c t i o n F a i l 3 9 when Main CPU was rewritten.
Page 53
Error Details of Error code Display Coping strategies Code DSP, PLD etc. failed to receive Turn off and on the power. firmware for rewriting sent from U p d a t i n g f a i l Updating starts automatically. DM860 (when timed out).
Page 54
Error Details of Error code Display Coping strategies Code Line congestion via DPMS access Check the network connection. was notified when DM860 related Carry out the update in an environment S e r v e r b u s y A 3 firmware was rewritten (Application that has little network load.
Page 55
Device display during firmware update d Display of target device during firmware update. Target device Display Error code when an error occurs 08 - 0C 10 - 15 Main M a i n : * * % * * * m i n 22 - 24 36 - 3E 50 - 52 Audio PLD...
ADJUSTMENT Audio Section Adjusting Idling Current Required measurement equipment: DC Voltmeter 1. Preparation (1) Temperature should be at avoid direct blow from an air conditioner or an electric fan and humidity should be moderate, and place the set at normal usage environment. 15 °C ~ 30 °C (59 °F ~ 86 °F) (2) Presetting •...
TROUBLE SHOOTING 1. POWER 1.1. Power not turn on Power not turn on. When the power turned on, When the power turned on, does the ON/STANDBY does the ON/STANDBY indicator on the front panel indicator on the front panel flashing green? flashing red? Is the fuse blown? Refer to 1.2.Fuse is blown.
2. Analog video MONITOR OUT (CVBS) output NG Input CVBS Input S Input Function : SAT Function : DOCK COMPONENT To A To B Not output HDMI OUT output NG Input CVBS Input S Input COMPONENT Input Function : SAT Function : DOCK Function : SAT HDMI...
Page 63
Input CVBS Is the power supply voltage correctly output? FRONT CONNECTOR B'D REGULATOR B'D flaw. V+5V : CP13B-4pin V-5V : CP13B-1pin Check on set value of each IC. Is they the following voltage values? HDMI B'D HDMI B'D flaw. FB112 : H(5V) FB114 : L(0V) FB116 : L(0V) FB124 : H(5V)
Page 64
Input Is the power supply voltage correctly output? FRONT CONNECTOR B'D REGULATOR B'D flaw. V+5V : CP13B-4pin V-5V : CP13B-1pin Check on set value of each IC. Is they the following voltage values? HDMI B'D HDMI B'D flaw. FB124 : L(0V)) FB126 : L(0V) FB118 : L(0V) FB120 : L(0V)
Page 65
Input CVBS/S/COMPONENT Check the input signal to VIDEO DECODER. Is signal confirmed for the Input CVBS : Check A- q - t following point? Input S : Check B- q - t Check the signal of signal DET. HDMI B'D If no problems are found in the Is they the following voltage values? : FB68...
Page 66
Input COMPONENT Is the power supply voltage correctly output? FRONT CONNECTOR B'D REGULATOR B'D flaw. V+5V : CP13B-4pin V-5V : CP13B-1pin Check on set value of each IC. Is they the following voltage values? HDMI B'D HDMI B'D flaw. FB100 : H(5V) FB103 : H(5V) FB122 : H(5V) Extend HDMI B'D using a jig.
(6) Is the BD/DVD player's HDMI output setting correct? the BD/DVD player operating instructions. (7) When you use a DENON BD/DVD player, is the fluorescent display tube's "HDMI" indicator lit? If you use a non-DENON BD/ DVD player, proceed to "YES".
Page 69
JACK4/JACK5/JACK7) display's "HDMI" indicator lit? JACK4/JACK5/JACK7 : TP[D_5V]) for the input on to the IC (U1 or IC9) are If using a non-DENON BD/ the side on which the BD/DVD player is connected. defective. DVD player, proceed to "NO". Is communication waveform confirmed in TP[SCL/ Replace the IC9.
Page 70
Check operation of each device. (AMP source : BD / Video input of player : 480P / Connect the TV.) Check operation of U1(ADV3002). (20) Check power supply. Are 5V or 3.3V supplied to U1 (each power supply pin)? The power supply circuitry is defective. Refer to [Detail C] of the substrate for test point.
Page 71
3.2. No picture is output (Analog to HDMI) No picture is output. (1) Is the set's input set to ANALOG VIDEO input(CVBS/S/ Check set's input setting, referring to the COMPONENT)? set's operating instructions. The set does not recognize the TV. (2) Is TP [HP_TX] set to the "H"(3V-5V)? The pattern and circuit from the HDMI With the TV connected,check the voltage of the IC on the side on...
Page 72
(8) Check the input signal Is each waveform confirmed with the following terminal of IC12? 2pin : 1TXVSYNC 79pin : 1TXPCK The U4 is defective. 97pin : 1TXDE 98pin : 1TXHSYNC (If the waveform is not the reference waveform, proceed to NO.) Check operation of IC12(ADV7511) (9) Check power supply.
Page 75
DDC_CLK/DDC_DATA/TMDS : Check items HDMI to HDMI (17)/(19)/(23), Check items Analog to HDMI (2)/(11) 0.9V DDC_CLK 2.48V TMDS Waveform DDC_DATA Timing waveform illustration from the start of CEC3.3V to when reset is released : Check items HDMI to HDMI (21)/(26), Check item Analog to HDMI (14) CEC3.3V 330ms...
Page 76
Controlled waveform(I2C), when power is turned on : Check item HDMI to HDMI (22), Check item Analog to HDMI (7) HSCL HSDA POWER ON 1TXDE/1TXVSYNC/1TXHSYNC/1TXPCK : Check item Analog to HDMI (8) 31.76us 1TXDE 1TXDE 31.84us 1TXHSYNC 1TXHSYNC 16.68ms 1TXVSYNC 1TXVSYNC 1TXPCK 37.0ns...
4. AUDIO 4.1. AUDIO CHECK Audio output NG. Refer to "Audio Check PATH" (85 page). CHECK1 INPUT SURROND MODE SOURCE Check ANALOG audio BLOCK. Audio output OK? ANALOG 2CH DIRECT ANALOG CHECK2 INPUT SURROND MODE SOURCE Check Digital audio BLOCK. Legacy Audio output OK? COAX or OPT...
Page 78
4.2. Power AMP (MAIN UNIT) No sound is output. The protector operates. Is the power transistor open or short- circuited? Replace the power transistor. 2SB1560/2SD2390 Is the emitter resistance of the power transistor open? Replace the emitter resistance. 0.47Ω Is the base resistance of the power transistor open? Replace the base resistance.
4.3. Analog audio No sound is output Is the voltage of ±8V supplied to The power supply of ±8V is repaired. AV B'D CP14? Is the audio signal transmitted to The power amplifier is repaired. AV B'D CN401? Connect the connectors properly. Is the serial data for electronic volume Is the connector correctly connected transmitted to AV B'D CP14?
5. Network/USB 5.1. Cannot connect to network Checking the environment Turn off the power and check the LAN cable Is the LAN cable properly connected? properly, and then turn the power back on. Checking the settings Set the IP address and other parameters properly.
Page 81
5.2. USB device is not recognized Checking the USB device Are you using a USB hub? Don't use the USB hub. Only mass storage devices in FAT16 or FAT32 format or MTPcompatible devices Is the USB device compatible with the set? and iPod (Remove some models) are supported.
6. SMPS DC 5V is not output. Is there damage in IC102 Replace the IC102(TOP258MG) and (TOP258MG)? D100/D101/D102/D104. Is there the damage in D100/D101/ Is the fuse (F100) blown? Replace the damaged parts. D102/D104/C102? Does the jumper (D301) wire connected to the PWB have disconnection or Repair the jumper wire.
Page 84
Operation waveform for each part Primary drain (Caution: High voltage, electric shock) After primary side rectification (Caution: High voltage, electric shock) After secondary rectifications OPTION SMPS B'D OPTION E3 L101 C131 0.01/250V L100 OPTION OPEN LF4ZBE273H J151 JUMPER D100 1N4007 ZD100 D101 1N4007...
LEVEL DIAGRAM LEVEL DIAGRAM FRONT ch R2A15218FP ANALOG H/POUT SPEAKER LINE IN + GAIN ADJ. + MIC IN + AK5358B + + AK4358VQ - - AZ4580 MAX.OUTPUT 7.78Vrms +30dB SP OUT R2A15218 MAX.OUTPUT 3.8Vrms AK4358VQ 4.24Vrms/8Ω DIFF.OUT AK5358B 0dBFS=5Vpp =1.77Vrms FULL SCALE LEVEL=2Vrms +20dB SINGLE INPUT...
Page 92
LEVEL DIAGRAM ZONE2 R2A15218FP SURR.BACK FRONT/ZONE ASSIGN from F-ch from SPEAKER DA SB-ch + LINE IN + MAIN NET/USB LINEOUT ZONE2 DAC (AVR2112 ONLY) AK4424ET +30dB SP OUT AK4424ET 4.24Vrms/8Ω Single end OUT 0dBFS=5.66Vpp MAX SIGNAL LEVEL 2.00Vrms =2Vrms +20dB +20dB 0dBFS +10dB...
REG_CNT 2/4 SIDE CONNECTOR OPTION_M OPTION_N RC5/M-X PORT RC5/M-X PORT MODEL AVR1712 AVR1912 AVR2112 REG_CNT 4/4 B6 REG_CNT 4/4 B3 AREA E2 E1C EA OPTION M OPTION N OPTION O CN402 CN403 C125Z2-11P C125Z2-13P DIGITAL CNT DIGITAL CNT HDMI 13/13 N4 HDMI 13/13 N3 OPTION_O EXT_IN 1/1 E5...
C365 C366 R187 OPEN 100N-K 10N-K R188 OPEN IC11 MX25L3206EM2I-12G * IC11 OPTION SCHEMATIC DIAGRAMS (14/26) DENON MODEL : AVR2112/AVR1912/AVR1712 HDMI UNIT (3/13) E2/EA/E1C : MX25L6406EM2I-12G (64M) E3/JP : MX25L3206EM2I-12G (32M) HDMI/TMDS SIGNAL LINE POWER + POWER - STBY POWER...
NET/PHY TO DM860 AVR1712 ONLY ALL OPEN TO AUDIO PLD 860SPDIF NET3.3V FROM D_SUPPLY DGND OPEN R262 R263 DLW21SN181SQ2L R264 OPEN 5P(20010WS) microSMD175F 0(2012) IC13 MFI341S2164 R265 R266 2 3 4 5 OPEN R272 FDC608PZ PHY_RST C552 4.7UF-K C553 OPEN R273 E_RESETN C554...
TO DIR/AUDIO PLD MAIN DAC R563 0(1608) R564 R565 OPEN OPEN C798 R566 C799 OPEN OPEN 10/16(MVG) R568 R567 ADINR OPEN OPEN DAGND ADINL C800 IC27:A C802 OPEN OPEN OPEN DAGND R570 0(1608) DACRTNGND R571 0(1608) R572 0(1608) R574 R573 OPEN DASBR OPEN...
CPU LEVEL CHG TO DIGITAL CONNECTOR AVR2112 AVR1912 AVR1712 0-1608 OPEN OPEN *OPTION "E" USE FOR NON-RDS MODEL FROMD.SUPPLY CEC3.3V CEC5V REMOTE3.3V SWM5V SWM3.3V M3.3V DGND FROMD.SUPPLY R661 FFC-4P M3.3V 232MO 232MI SWM3.3V DGND C980 OPEN R687 R688 R689 DGND R824 SWM3.3V 19 18 17...
DSP PARTS TO CPU LEVEL CHG ADV7511 ADV3002 APLD+DAC HDMI PARTS MODEL AVR1712 AVR1912 AVR2112 AREA E3 E2 OPTION A OPTION B OPTION C OPTION D OPTION E TO D.SUPPLY CEC_COM ADV7623_INT1 ADV7623_INT2 ADV7623_TX_INT MAIN_POWER ADV7623_SPI_MO ADV7623_SPI_MI BDOWN R845 OPEN ADV7623_SPI_CLK E_POWER R846...
EXPLODED VIEW J X3 L X3 AVR2112CI BKE3 (INLET) AVR2112 BKCIE3 AVR1912 BKE2/BKEA J X3 A X6 A X17 B X2 C x5 32 X5 E X2 C X5 AVR1912 BKE3 C X5 H X21 G x4 A X3 A X17 J X2 (INLET) AVR1912 BKE2/BKEA...
PARTS LIST OF EXPLODED VIEW z Parts indicated by "nsp" on this table cannot be supplied. z P.W.B. ASS'Y indicated by "nsp" on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts list and order replacement parts. z Parts indicated by the "...
Page 137
Ref. No. Part No. Part Name Remarks Q'ty New BRACKET SIDE 4010210686000S CHASSIS BACK 1912BKE3 3207213806100S CHASSIS BACK 2112CIBKE3 3207213806000S CHASSIS BACK 1912BKE2,1912BKEA 3207213806200S CHASSIS BACK 1912SPE1C 3207213806300S STOPPER CORD AC E3,E1C 4380210002000S 00D9630292205 CORD ASSY L068125100020S 963611500410S CORD ASSY L068250060011S 963101100020S POWER TRANS MAIN...
PACKING VIEW E3,E1C model E2,EA,E1C model SP model E2,EA model E2,EA model E1C model E2,EA model SP model E2,EA model E1C model PARTS LIST OF PACKING & ACCESSORIES z Parts indicated by "nsp" on this table cannot be supplied. z Parts indicated by the " ★ " mark are not illustrated in the exploded view. z The parts listed below are only for maintenance.
Page 139
BOX GIFT 1912BKE3 6007211860000S 963531013500D BOX GIFT 2112CIBKE3 6007211860010S 963531013530D BOX GIFT 1912BKE2,1912BKEA 6007211860040S 963531013540D BOX GIFT 1912SPE1C 6007211860020S LABEL DENON CONTROL 5507000007000S LABEL MAC ADDRESS 5507000002920S 90M-ZC000600R AC CORD L068250160020S 963611001490S AC CORD L068250100070S BUSHING E2,EA,E1C 2410040353010S COLOR LABEL 5507020170680S...
EX3AV SEMICONDUCTORS Only major semiconductors are shown. General semiconductors etc. are omitted from list. The semiconductors which have a detailed drawing in a schematic diagram are omitted from list. Temp Rating EX3AV Part Number (° C) Package 1. IC's EX3AV -40 to +85 38-pin QFN T&R...
Page 143
Pin No. Mnemonic Type Description RXC_2− HDMI input Digital Input Channel 2 Complement of Port C in the HDMI Interface. RXC_2+ HDMI input Digital Input Channel 2 True of Port C in the HDMI Interface. HP_CTRLD Digital output Hot Plug Detect for Port D. 5V_DETD Digital input 5 V Detect Pin for Port D in the HDMI Interface.
Page 144
Pin No. Mnemonic Type Description RXC_2− HDMI input Digital Input Channel 2 Complement of Port C in the HDMI Interface. RXC_2+ HDMI input Digital Input Channel 2 True of Port C in the HDMI Interface. HP_CTRLD Digital output Hot Plug Detect for Port D. 5V_DETD Digital input 5 V Detect Pin for Port D in the HDMI Interface.
Page 145
Pin No. Mnemonic Type Description PGND Ground PVDD Ground. PVDD Power PLL Supply Voltage (1.8 V). XTAL Miscellaneous Input pin for 28.63636 MHz crystal or an external 1.8 V 28.63636 MHz clock oscillator source to analog clock the ADV7623. XTAL1 Miscellaneous Crystal Output Pin.
ADV7623 Block diagram I 1.4 Fast Switching Receiver with 12-Bit, 170 MHz XTAL XTAL1 VIDEO DATA nd Graphics Digitizer and 3D Comb Filter Decoder RXA_C RXB_C RXC_C AUDIO DATA VIDEO DATA RXD_C ADV7844 RXA_0 EQUALIZER SAMPLER RXA_1 RXA_2 AUDIO DATA VIDEO DATA RXB_0 VIDEO DATA...
Page 147
SECTION 5: PIN AND PACKAGE INFORMATION This section shows the pinout of the ADV7511 100-lead LQFP package. This section also contains a brief description of the different pins as well as the mechanical drawings 100-lead LQFP configuration (top view - not to scale) Figure 6 ADV7511BSTZ (HDMI : IC12) PIN 1...
Page 149
±15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWR in a Small Footprint Datasheet LAN8700-AEZG-TR Pin Description Table 2.1 LAN8700/LAN8700I 36-PIN QFN Pinout PIN NO. PIN NAME PIN NO. PIN NAME nINT/TX_ER/TXD4 RX_DV RX_CLK/REGOFF CRS/PHYAD4 RX_ER/RXD4 MDIO TXCLK nRST TXD0...
Page 150
SAA7121H (HDMI : IC15) 33 V SSA2 res. V SSA1 V DDA3 CVBS V SSD1 res. SAA7120 V DDD1 V DDA2 SAA7121 RCV1 res. RCV2 V DDA1 res. MBH790 SAA7121H Block Diagram V DDA1, handbook, full pagewidth RCV1 TTXRQ XTALO V DDA2 , V DDA4 V DDA3...
Page 151
Digital Video Encoder (ConDENC) SAA7120; SAA7121 SAA7121H Pin Description PINNING SYMBOL DESCRIPTION res. − reserved test pin; connected to digital ground for normal operation test pin; connected to digital ground for normal operation line-locked clock; this is the 27 MHz master clock for the encoder digital ground 1 SSD1 digital supply voltage 1...
Page 152
LC89058W-E (HDMI : IC19,21) 35 34 33 32 31 30 29 28 27 26 25 SDIN SLRCK SBCK RDATA XMODE RLRCK LC89058W-E DV DD DGND DGND DV DD RBCK GPIO0 GPIO1 RMCK GPIO2 AGND GPIO3 AV DD RXOUT2 * : Pull-down resistor internal at no selection Pin Functions RXOUT1 RX0-6 input S/PDIF through output pin 1...
Page 153
LC89058W-E Continued from preceding page. Pin No. Name Function DGND Digital GND DV DD Digital power supply (3.3V) XMCK Oscillation amplifier clock output pin XOUT Output pin connected to the resonator External clock input pin, connected to the resonator (12.288MHz/24.576MHz) DV DD Digital power supply DGND...
Page 154
ADSP21487KSWZ3B (HDMI : U8) PIN 1 GND PAD (PIN 177) at BOTTOM TOP VIEW (PINS DOWN) ADSP21487KSWZ3B Terminal Function Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. SDDQM DAI_P10 DPI_P08 FLAG0 SDCKE DPI_P07 FLAG1 DAI_P20...
W9864G2IH W9864G6JH-6 Pin description 5. PIN DESCRIPTION PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Row address: A0−A10. Column address: A0−A7. 24, 25, 26, 27, 60, 61, 62, A0−A10 Address A10 is sampled during a precharge command to 63, 64, 65, 66 determine if all banks are to be precharged or bank selected by BS0, BS1.
Page 158
EN29LV160BB-70TIP (HDMI : U7) BYTE# DQ15/A-1 DQ14 DQ13 Standa rd DQ12 TSOP RESET# DQ11 RY/BY# DQ10 EN29LV160BB-70TIP Block Diagram Block Diagram RY/BY# DQ0-DQ15 (A-1) Block Protect Switches Erase V oltage Generato r Input/Output Buffers State Control Program Voltage Generato r Command Chip Enable Regi s ter...
Page 164
Pull up/ Pin Name Symbol LvCnv STBY Function down STBY 14 VCL Smoothing capacitor connection pin 15 MD1 M3VPu 16 MD0 M3VPu 17 P86 (MUTE POWER) Reserve (PRE MUTE control) 18 P85 REMOTE POWER(232C) 232C POWER control pin(ON: H) 19 RES# RESET Reset input pin (reset: L) 20 XTAL...
Page 165
Pull up/ Pin Name Symbol LvCnv STBY Function down STBY 60 P81/TRSYNC FL RST FL control order pin 61 P80 S VSEL B S VIDEO switcher control pin (TC4052) MINI JACK connection detection pin for DOCK 62 BCLK/P53 iPod DET SW3VPu connection(Connection:H) 63 P52/RD#...
Page 166
Pull up/ Pin Name Symbol LvCnv STBY Function down STBY 110 PD7/D7 JTAG TDO A.PLD rewriting control pin(JTAG) 111 PD6/D6 JTAG TMS/APLD CS A.PLD rewriting & control pin 112 PD5/D5 JTAG TDI/APLD DATA/DAC DATA A.PLD rewriting & control /DAC control pin 113 PD4/D4 JTAG TCK/APLD CLK/DAC CLK A.PLD rewriting &...
Page 167
MC14094B MC14094BDTR2G (HDMI : IC35) PIN ASSIGNMENT STROBE OUTPUT DATA ENABLE CLOCK Q′ TRUTH TABLE Parallel Outputs Serial Outputs Output Enable Q′ Clock Strobe Data No Chg. No Chg. No Chg. No Chg. No Chg. −1 No Chg. −1 No Chg. No Chg.
Page 168
CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control BLOCK DIAGRAM AND PIN CONFIGURATION (TOP VIEW) R2A15218FP (AV : IC801) TRER MUTE AVEE AVCC BASSR2 AVEE BASSR1 ADCL 0/-6/-12/-18dB ADCR TREL SUB2 AGND BASSL2 MAIN INR1 BASSL1 Bass/ Treble 0~-95dB, +42~0dB -14~+14dB...
Page 169
R2A15220FP R2A15220FP CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control PIN DESCRIPTION R2A15218FP Pin Function PIN No. Function Name FROUT,FLOUT, 22,20, COUT,SWOUT, 16,14, Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel SROUT, SLOUT, 10, 8, SBROUT,SBLOUT 2, 100 23,19, FR Pre-out,FL Pre-out, Pre-output pin of FL/FR/SL/SR/SBL/SBR channel 11, 7, SR Pre-out, SL Pre-out,...
PARTS LIST OF P.C.B. UNIT z Parts indicated by "nsp" on this table cannot be supplied. z The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks"...
PCB REG_CNT ASS'Y Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP IC103 00D2630553006 IC NJM7805FA J126780500130S IC104 00D2630554005 IC NJM7905FA J126790500020S IC105 00D2630553006 IC NJM7805FA J126780500130S IC106 00D2630810008 IC NJM7808FA J126780800030S IC107 00D2630503001 IC NJM7908FA J126790800020S IC108 963239003420S IC NJM2388F05 2112CIE3,1912E3 J126238800050S 1912E2,1912EA,...
PCB AUDIO_VIDEO ASS'Y Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP IC801 963239000650S IC R2A15218FP J084152180010S IC806 963233100020S IC TC4052BFT J040405205510S IC821 232810005504S IC BD7628F-E2 J127762800010S IC822 00D2623445901 IC TC4051BFT J040405105510S IC823 232810005504S IC BD7628F-E2 J127762800010S IC825 963239003470S IC NJM2586AM J171258600010S IC826 963233100020S IC TC4052BFT...
PCB HDMI ASS'Y NOTE: When replacing the AVR1912E2, EA, E1C IC18 or IC41, use the AVR2112CIE3, AVR1912E3 IC18(963248100110S) or IC41(963243100070S). When replacing the AVR1912E1C IC11, use the AVR1912E2 (EA) IC11(963248100710S). When the following are replaced, always rewrite with updated firmware using DFW. (Refer to "PROCEDURE FOR UPGRADING THE VERSION OF THE FIRMWARE"...
Page 189
Ref. No. Part No. Part Name Remarks Q'ty IC CPU MICRO PROCESS IC41 963243100070S 2112CIE3,1912E3 8952191200010 (R5F56108VNFP) IC CPU MICRO PROCESS 1912E2,1912EA, IC41 (R5F56108VNFP) 1912E1C NOTE : When replacing the 1912E2(EA) or E1C parts, use the 1912E3/2112CIE3 parts. After replacing the parts, overwrite the firmware with the newest 1912E2(EA) or E1C version firmware. 236810057606S IC LOGIC ADV3002BSTZ J040300205510S NOTE :...