Rf Transmitter Points - NAPCO LIBRA LIB-P432EX Programming Instructions Manual

USER OPTIONS
USER CODE AREA 1 AREA 2
OPTIONS OPTIONS
(UP TO 6 DIGITS)
CODE TYPE
Disabled User Code not active.
Arm/Disarm Allows User Code to arm/disarm.
Arm Only Prevents User Code from disarming.
A Service Code has restricted arm/disarm rights; if an area is armed with a Service Code,
a "SERVICE ON" appears on the GEM-DXRP2 keypad and the area can be disarmed with any
Service valid User Code, including a Service Code. If the area is armed with OTHER than a
Service Code, it CANNOT be disarmed with a Service Code. This is typically used to
allow tradesmen access to premises under control of the owner.
This is normally used to activate a door strike. Also program "Access Control on PGM2
Access
Output" (Address 0719) and "PGM2 Output Access Control Timeout" (Address 0711).
There are two types of Ambush Codes: (1) A 2-digit code (prefix) that is entered
immediately prior to (and as part of) the regular User Code and (2) A separate and
unique User Code. Disarming with an Ambush Code will cause a silent report to be
Ambush
sent to a central station. Thus, should a user be forced to disarm, he can silently signal
an emergency while appearing to be merely disarming the system.
User Program Option is enabled for Keypad 1 only, wherever it is connected. To enable
User Program Option for any user add 8 to the data entry Option (see example). Then,
* User Program
User Programming can be performed only at Keypad 1 by a user code with user program
enabled.
Bypass Enable Security Bypass--Bypass is enabled only with a security code.
Related User Options: "Enable Global Ambush Code" (Address 1422) & "Global
Ambush Code" (Address 2045).
28
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
Quick Enroll Method
If a receiver is already installed in the panel, Napco transmitter
wireless points can be programmed automatically ("enrolled")
using the following procedure. NOTE: The transmitter point will
be enrolled only if the signal strength is 3 or greater.
1. Enter the zone number to which the transmitter point will be
mapped.
2. Press the button to enter the Enroll Mode. The red
x
and green LEDs on the keypad will flash and the window will
display as shown at left.
3. Open the loop of the point that is to be programmed (GEM-
TRANS2 or GEM-TRANS4 only).
4. Install the transmitter battery.
indicate that the point has been successfully enrolled. Multi-
point transmitters can be mapped to successive zones
simultaneously (Example 1) or to selected zones point by
point (Example 2).
Example 1. A 4-point transmitter has the RF ID number
410078:1. Map the first three points to Zones 11–13,
respectively.
1. Enter the Enroll mode as described in step 2 above.
2. Enter Zone "11".
NAPCO Security Systems
USER AREA OPTIONS
AREA 3 AREA 4
DATA ENTRIES
OPTIONS OPTIONS
L
blank(•)
blank(•)
blank(•)
blank(•)
blank(•)
blank(•)
blank(•)
4
EXPLANATION
RF Transmitter Points (Press the (
(For wireless systems only. Also see Quick Method, which follows).
For each transmitter (key fob transmitters also), enter the zone number (01–64) to which the
transmitter will be mapped, the 6-digit RF ID#: 1-digit checksum number printed on the transmitter and
box, the point number (1–4); enter "9" for unsupervised (all points). NOTE: When programming the
ID Code number, "A" =
; "F" =
G4 G5
The keypad will beep to
USER OPTIONS: Area 1-4 options for 64 Us-
OPTION
ENABLED
R
blank(•) Disabled
1 Arm/Disarm
2 Arm Only
3 Service
Example: Program a code of "1234" for user 02,
4 Access
with Area 1 options of "Arm/Disarm" and "User
5 Ambush
Add 8 * User Program
Program":
blank(•) Bypass Enable
With "27" displayed in keypad window, press
w
1234
0
options),
u
Notes: (1) For User Code, press
for Blank Space; (2) For User Options, press
0
CHANGING OR CANCELING A CODE: To change
any code, merely program over the existing code as
described above and press
cancel a code, blank out each number of the code
and press
are not allowed; therefore a duplicate Code entered in the
LCD Window will erase when
) button to set cursor)
w
; "B" =
G0 G1
u
. Press to save. Press NEXT ("r" or
3. Open the loops of points 1, 2 and 3.
4. Install the transmitter battery. The keypad will beep 3 times
to indicate that three points have been programmed.
Transmitter 410078:1, point 1 will be mapped to Zone 11.
Transmitter 410078:1, point 2 will be mapped to Zone 12.
Transmitter 410078:1, point 3 will be mapped to Zone 13.
The keypad will now display Zone 13, the last zone enrolled.
Example 2. A 2-point transmitter has the RF ID number
287613:1. Map point 1 to Zone 6 and point 2 to Zone 9.
1. Enter the Enroll mode as described above.
2. Enter Zone "06".
3. Open point-1 loop.
4. Install the battery. The keypad will beep once to indicate
that one point has been programmed.
287613:1, point 1 will be mapped to Zone 6).
5. Enter Zone "09".
6. Close point-1 loop and open point-2 loop.
7. Remove the transmitter battery, then re-install it.
keypad will beep once to indicate that one point has been
programmed. (Transmitter 287613:1, point 2 is mapped to
Zone 9).
LIBRA LIB-P432EX Series Programming Instructions
ers:
Select the desired options from the table
shown and enter in the remaining boxes
for each user code.
, (User 2),
0 2 w
,
G 0 G
(User Code),
09
(User Area 2 Options), and
00
(save).
for Blank Space.
u
to save. Similarly, to
u
to save. Note: Duplicate User Codes
u
is pressed.
; "C" = ; "D" =
G2
p ) to proceed.
Page 17
(User Area 1
G 0
; "E" =
G3
(Transmitter
The