Rf Transmitter Points - NAPCO Gemini GEM-P1632 Programming Instructions Manual

!
Page 10
USER OPTIONS
USER CODE AREA 1
OPTIONS
(UP TO 6 DIGITS)
AREA OPTIONS
Disabled User Code not active in this area.
Arm/Disarm Allows User Code to arm/disarm this area.
Arm Only Prevents User Code from disarming this area.
Service A Service Code has restricted arm/disarm rights; if an area is armed with a
Service Code, a "
area can be disarmed with any valid User Code, including a Service Code. If
the area is armed with OTHER than a Service Code, it CANNOT be disarmed
with a Service Code. This is typically used to allow tradesmen access to
premises under control of the owner.
Access This is normally used to activate a door strike while an area is disarmed. Also
program "Access Control on PGM2 Output" (Address 0719) and "PGM2 Output
Access Control Timeout" (Address 0711).
Ambush Allows User Code to send Ambush signal to Central Station.
* User Program User Program Option is enabled for Keypad 1 only, wherever it is connected
(Area 1 or Area 2). To enable User Program Option for any user add 8 to the
data entry for Area 1 Option (see example). Then, User Programming can be
performed only at Keypad 1 by a user code with user program enabled.
Related User Options: "Enable Global Ambush Code" (Address 0720),
"Global Ambush Code" (Address 1054) & "Enable Managers Mode" (Address 0719).
CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described above and press
U
to save. Similarly, to cancel a code, blank out each number of the code press
RF Transmitter Points (Press the (
(For wireless systems only. Also see Quick Method, which follows)
Zn# 01
For each transmitter (key fob transmitters also), enter the zone number (01–32) to which the transmitter
will be mapped, the 6-digit RF ID #:1-digit checksum number printed on the transmitter and box, the
000000
point number (1–4); enter "9" for unsupervised (all points). NOTE: When programming the ID Code
number, "0" through "9" =
(Direct Entry)
G 2
save. Press the NEXT/YES button button to proceed.
:0 Pt
(Direct Entry)
Quick Method.
If a receiver is already installed in the panel, Napco transmitter
wireless points can be programmed automatically ("enrolled")
using the following procedure. NOTE: The transmitter point will
be enrolled only if the signal strength is 3 or greater.
1. Enter the zone number to which the transmitter point will be
mapped.
2. Press the button to enter the Enroll Mode. The red and
B
green LEDs on the keypad will flash.
3. Open the loop of the point that is to be programmed (GEM-
TRANS2 only).
4. Install the transmitter battery. The keypad will beep to indicate
that the point has been successfully enrolled.
transmitters can be
simultaneously (Example).
X
GEM-P1632 Programming Instructions
USER AREA OPTIONS
AREA 2
DATA ENTRIES
OPTIONS
L
blank(•)
blank(•)
blank(•)
blank(•)
blank(•)
blank(•)
blank(•)
EXPLANATION
MONITOR ON
" appears on the GEM-RP2ASe2 keypad and the
0
; "D" = G 3
Multi-point
mapped to successive
AREA OPTIONS: Area 1 and Area 2 Options
OPTION
may be programmed for all 32 users.
ENABLED
R
!
blank Disabled
1 Arm/Disarm
2 Arm Only
3 Service
Example: Program a code of "2222" for user 02, with
4 Access
area 1 options of "Arm/Disarm" and "User Program".
5 Ambush
Enter "2222" for a user code, "•(blank) 9" for area 1
options and "•(blank) •(blank)" for area 2 options.
Add 8 * User Program
!
For Area 2 Options (ACC), press
again.
options. NOTE: Press
!
Press
Code, press
Number and change it using the number buttons.
Program a new User Code as previously described.
Remember to record your user codes in the Easy
Menu Programming Worksheet at the back of this
manual.
U
R ) button to set cursor.)
through ; "A" =
9 G 0
; "E" = G 4
Example. A 2-point transmitter has the RF ID number 287613:1.
Map point 1 to Zone 6 and point 2 to Zone 9.
1. Enter the Enroll mode as described above.
2. Enter Zone "06".
3. Open point-1 loop.
4. Install the battery. The keypad will beep once to indicate that
one point has been programmed. (Transmitter 287613:1, point
1 will be mapped to Zone 6).
5. Enter Zone "09".
6. Close point-1 loop and open point-2 loop.
7. Remove the transmitter battery, then re-install it. The keypad
will beep once to indicate that one point has been
programmed. (Transmitter 287613:1, point 2 is mapped to
zones
Zone 9).
Select the desired Area Options (Area 1 and
Area 2) from the table shown and enter in
the remaining four boxes for each user code.
Refer to the table above for available
for blank space (•).
0
U
to save. To proceed to the next User
to set the cursor to the User
R
to save.
; "B" =
G 1
and "F" = G 5
L
NAPCO Security Systems
once
A
; "C" =
U
. Press to