Page 2
Information furnished by NAPCO is believed to be accurate and reliable. However, no responsibility is assumed by NAPCO for its use; nor for any infringements of other rights of third parties which may result from its use. No li- cense is granted by implications or otherwise under any patent or patent rights of NAPCO.
ING SUITABLE TRAINING, EXPERIENCE AND INSTALLATION EQUIPMENT. IT IS RECOMMENDED THAT AFTER PRO- GRAMMING, THE ERROR CHECK UTILITY OF PCD-WINDOWS DOWNLOAD SOFTWARE BE USED TO VERIFY THAT THE CONTROL PANEL PROGRAM CONTAINS NO ERRORS OR CONFLICTS WHICH MAY INHIBIT ITS INTENDED OPERATION. NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 3...
● Maximum Total combined 24V Standby and Alarm Current: total 12V standby and 12V alarm current must not exceed 2.5A. * Must be reduced if an insufficient number of standby batteries are used. Refer to Battery Standby chart. NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 3...
GEMC-FK1 and GEMC-BK1 are both powered by the keypad bus of the control panel, GEMC-12V2APS or an appropriately rated UL Listed Security/Signaling power-limited power supply. Deduct these values from the system standby current, as described in the control panel wiring diagram. NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 3...
24 hours. Any of the 4 NACs can be used for auxiliary out- Operating Humidity Range: Maximum 85% relative humidity @ 30°C. puts by programming the output with the feature "Reverse Polari- NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 3...
Note: Detector stabilizes within 3 minutes of power up. monitored by a central station. Relative humidity: 85% (non-condensing) Glass types: minimum size: 10-7/8" x 10-7/8", (280 mm x 280 mm) 3/32" - 3/8" • plate; NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 3...
All wiring must comply with the NEC (National Electrical Code) and/or NFPA 70 codes. NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 3...
Burg Exit/Entry Trouble Restore R381 Transmitter Trouble Restore E137 Burg Zone Tamper Alarm E608 Test Timer (Fire System Faulted) R137 Burg Zone Tamper Restore E374 Exit Error E370 Burg Zone Tamper Trouble E459 Recent Close NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 3...
Page 11
Fail to Check-In E342 Fire Monitor AC Fail E998 Used to Disable Restores R342 Fire Monitor AC Fail Restore E342 Fire Monitor AC Fail Trouble R342 Fire Monitor AC Fail Trouble Restore NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 3...
• Honeywell Ademco Wave 2 (2-Tone Siren) GEMC-FW-SLC: Fire SLC Module (see WI1647) GEMC-HSKIT1416: Small Enclosure only + PCB mounting bar kit * Not investigated by UL. ** Not investigated by UL for Commercial applications. NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 3...
Page 13
Burg Module, provides isolated 4-wire Burg bus for Burg key- less or conventional fire devices, 4 on board NACs provid- pads and devices, plus 12V power output for aux devices. ing up to 6.5A notification power Independent Burg Bell output. NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 3...
Page 14
SLC loop. Designed to be used with pull stations, water flow switches, and other applica- tions requiring the monitoring of dry contact alarm initiating devices. NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 3...
Excel file, available online at the NAPCO website: http://www.napcosecurity.com/ Once at the NAPCO website, click the link "Dealer support docs" and follow the links to find and download the Excel file to your local computer. This Excel file contains all of the calculation worksheets that may be required by the AHJ ("authority having jurisdic- tion") for each installation NAPCO Commercial (GEMC) C- Series configuration type, namely:...
7. Reconnect all wires to their correct terminals and reconnect all Modules. Place the Burg Service Jumper back to the OFF position to restore Burglary system operation. Test the system and resume normal premises operation. NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 3...
Page 18
NAC C + NAC D + NAC A - NAC B - NAC C - Zero (0) Volts NAC D - REM PWR - AUX PWR - 2 or 4 GEMC-FW-SLC Loop (-) NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 3...
4. The .hex file name references the Micro number (either Micro Micro example, "ComboMicro1.hex"). Therefore, for the Micro number referenced in the file name, click the appro- priate Browse button (within either the Micro 1 or NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 3...
Connect the EOL relay to a conventional or SLC zone programmed as a Fire Monitor Zone. (EXAMPLE) EOLR AS REQUIRED BY THE LOOP OUT ZONE LOOP IN +24V [–] (–) DEVICE NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 3...
Warning: The use of non-NAPCO wireless devices with this control panel has not been evaluated by UL and voids the UL listing. In addition, the performance of these devices can not be guaranteed as compatible with NAPCO control panels.