Fluke Calibration 6024 Manuals

Manuals and User Guides for Fluke Calibration 6024. We have 1 Fluke Calibration 6024 manual available for free PDF download: User Manual

Fluke Calibration 6024 User Manual

Fluke Calibration 6024 User Manual (83 pages)

Calibration Baths

Brand: Fluke Calibration | Category: Test Equipment | Size: 0.95 MB

Table of Contents

Table of Contents
3
1 Before You Start

9
- Symbols Used
  9
- Table 1 International Electrical Symbols
  9
- Safety Information
  10
  - Warnings
    10
  - Cautions
    12
- Authorized Service Centers
  14
2 Introduction

17
- Figure 1 6020 Series of Calibration Baths
  17
3 Specifications and Environmental Conditions

19
- Specifications
  19
- Environmental Conditions
  20
4 Quick Start

21
- Unpacking
  21
- Set up
  21
- Power
  22
- Setting the Temperature
  22
5 Installation

25
6 Bath Use

29
- General
  29
- Comparison Calibration
  29
- Calibration of Multiple Probes
  30
7 Parts and Controls

31
- Front Panel
  31
- Figure 3 Front Panel Features
  31
- Figure 4 Typical 6020 Series Calibration Bath
  32
- Bath Tank and Lid
  33
- Back Panel
  34
- Figure 5 Back Panel
  34
8 General Operation

37
- Bath Fluid
  37
  - Temperature Range
    37
  - Viscosity
    37
  - Specific Heat
    37
  - Thermal Conductivity
    38
  - Thermal Expansion
    38
  - Electrical Resistivity
    38
  - Fluid Lifetime
    38
  - Safety
    38
  - Cost
    39
  - Commonly Used Fluids
    39
    
    Water
    39
    
    Ethylene Glycol
    39
    
    Mineral Oil
    39
    
    Silicone Oil
    40
  - Fluid Characteristics Charts
    40
    
    Limitations and Disclaimer
    40
    
    About the Graph
    40
    
    Table 2 Table of Various Fluids and Their Properties
    41
    
    Figure 6 Chart of Various Bath Fluids
    42
- Stirring
  43
- Power
  43
- Heater
  43
- Cooling
  44
- Temperature Controller
  44
9 Controller Operation

47
- Bath Temperature
  47
- Reset Cutout
  47
- Figure 7 Controller Operation Flowchart
  48
- Temperature Set-Point
  49
  - Programmable Set-Points
    49
  - Set-Point Value
    50
  - Set-Point Vernier
    50
- Temperature Scale Units
  51
- Secondary Menu
  51
- Heater Power
  52
- Proportional Band
  52
- Figure 8 Bath Temperature Fluctuation at Various Proportional Band Settings
  53
- Proportional Band - Fluid Table
  54
- Cutout
  55
- Controller Configuration
  56
- Probe Parameters
  56
  - Alpha
    56
- Operating Parameters
  56
  - Cutout Reset Mode
    57
- Serial Interface Parameters
  57
  - Baud Rate
    57
  - Sample Period
    58
  - Duplex Mode
    58
  - Linefeed
    59
- IEEE-488 Parameters
  59
  - IEEE-488 Address
    59
- Calibration Parameters
  60
  - Cto
    60
  - CO and CG
    60
  - H and L
    60
10 Digital Communication Interface

61
- Serial Communications
  61
  - Wiring
    62
  - Setup
    62
    
    Baud Rate
    62
    
    Sample Period
    62
    
    Figure 9 Serial Communications Cable Wiring
    62
    
    Duplex Mode
    63
    
    Linefeed
    63
  - Serial Operation
    63
- IEEE-488 Communication (Optional)
  63
  - Setup and Address Selection
    63
  - IEEE-488 Operation
    64
- Interface Commands
  64
- Power Control Functions
  65
- Interface Command Summary
  66
- Power Control Functions
  67
- Interface Command Summary Continued
  67
11 Calibration Procedure

69
- Calibration Points
  69
- Measuring the Set-Point Error
  69
- Computing R0 and ALPHA
  69
- Calibration Example
  70
- Figure 10 Calibration Example
  71
12 Maintenance

73
- Draining the Bath
  74
13 Troubleshooting

77
14 Appendix - Model 6021

81
- Installation
  81
- Figure 11 6021 Back Panel
  83
- Auxiliary Chiller Control Functions
  83

Advertisement

Advertisement

Related Products

Fluke Calibration Categories

Test Equipment Measuring Instruments Water Pump

Monitor

Power Supply

More Fluke Calibration Manuals